Armstrong-Air/AirEase

Footprint (HxWxL): 36 1/4 x 34 x 48; 49 x 34 x 58 5/8; 49 7/8 x 57 5/8 x 65.

Serviceability features: Hinged or slide-out control box, liquid and suction line service valves, full perimeter base rails, high- and low-pressure switches, and short-cycle control.

Technical support: Technical service available from distributor or from manufacturer.

Noise-reduction features: Sound levels as low as 86 dB.

Humidity-control features: Not available.

Additional features: Low ambient operation to 0°F. Matching air handlers are also available.

Contact: Armstrong Air Conditioning, Inc., Bellevue, OH; Attn: Cabot Oglesby, 419-483-4840; 419-483-2933 (fax).

eProduct #60

MultiAqua

Footprint (HxWxL): Manufac-turer did not supply.

Serviceability features: Single-point service access; simplified component layout; and common, “off-the-shelf” parts.

Technical support: U.S. factory support and local sales rep-resentative support.

Noise-reduction features: 1/2-in. closed-cell foam insulation surrounds compressor/pump enclosure. It also has horizontal air discharge.

Humidity-control features: Latent capacity of chilled water; 100% of coil face area has latent capacity.

Additional features: Can be matched with a variety of mini-split and/or traditional chilled/hot water fancoils.

Contact: MultiAqua, Miramar, FL; Attn: Chuck Brewer, 954-431-1300; 954-431-1303 (fax); chuckb@multiaqua.com (e-mail); www.multiaqua.com (website).

eProduct #61

Trane

Footprint (HxWxL): Manufacturer did not supply.

Serviceability features: Cleanable, double-sloped, reversible drain pans; all foil face insulation; single-side access; single-point entry; completely assembled and ready to install.

Technical support: Full support from sales offices and manufacturing facility.

Noise-reduction features: Manufacturer did not supply.

Humidity-control features: Manufacturer did not supply.

Additional features: Dual compressors on 10- to 20-ton models; low ambient cooling oper-ation; flexible air hand-lers can be installed either vertically or horizontally; standard-ized cabinets; UL listed; ARI certified.

Contact: The Trane Company, Clarksville, TN; Attn: Jim Wallin, 931-648-5124; 931-648-5901 (fax); jim.wallin@trane.com (e-mail); www.trane.com (website).

eProduct #62

Addison

Footprint (HxWxL): 56 x 84 x 2251¼4 (largest).

Serviceability features: Manufacturer did not supply.

Technical support: Manufacturer did not supply.

Noise-reduction features: Sound attenuation options are available with specific models.

Humidity-control features: Humidity control option available with specific models.

Additional features: Dependent on model, there are hundreds of options available.

Contact: Addison, Orlando, FL; Attn: Gordon Nelson, 407-292-4400; 407-290-1329 (fax); info@addison-hvac.com (e-mail); www.addison-hvac.com (website).

eProduct #63

Carrier

Footprint (HxWxL): 58-68 x 86 1/2 x 116 1/2.

Serviceability features: Hinged access panels, ComfortLink™ control diagnostics, and slide-out fan deck.

Technical support: Contractor, distributor, or Carrier customer service, Carrier Corporation, Customer Relations, P.O. Box 4808, Syracuse, NY 13221; 800-227-7437; contact.carrier@carrier.utc .com (e-mail).

Noise-reduction features: Extremely low-velocity condenser airflow provides quiet operation.

Humidity-control features: Multirefrigerant circuits; selects lead circuit based on outdoor ambient temperature.

Additional features: Easy to install; fits on installed base of Carrier DP/DR/TJ/HJ rooftops, and therefore no additional roof curb required for replacement jobs.

Contact: Carrier Corporation, Syracuse, NY; Attn: Matt Placito, 315-432-3648; 315-433-4109 (fax); matthew.placito@carrier .utc.com (e-mail); www.carrier.com (website).

eProduct #64

Model: 48/50 HJ rooftop unit

Footprint (HxWxL): 3 ft x 6 ft x 7 ft, including clearance.

Serviceabilityfeatures: Hinged access panels, diagnostic controls, fully safety-protected, national training.

Technical support: Factory, regional, distribution, contractor, or Carrier customer service, Carrier Corporation, Customer Relations, P.O. Box 4808, Syracuse, NY 13221; 800-227-7437; contact.carrier@carrier.utc.com (e-mail).

Noise-reduction features: Fully insulated steel cabinet with isolated compressors and full base rails.

Humidity-control features: “Moisture Mi$er” and “Energy $ Recycler” models available.

Additional features: Easily field convertible duct connections; available in gas heat/electric cooling; electric heat/electric cooling; heat pump; and cooling-only models.

Contact: Carrier Corporation, Syracuse, NY; Attn: Matt Placito, 315-432-3648; 315-433-4109 (fax); matthew.placito@carrier .utc.com (e-mail); www.carrier.com (website).

eProduct #65

Model: 38 AK/AKS/AQS

Footprint (HxWxL): From 33 x 30 x 47.

Serviceability features: Suction and discharge service valves; semi-hermetic compressor on 7-to 30-ton models; easy access to compressor and controls; multipoise design indoor unit.

Technical support: Carrier Corporation, Customer Relations, P.O. Box 4808, Syracuse, NY 13221; 800-227-7437; contact.carrier@ carrier.utc.com (e-mail).

Noise-reduction features: Not available.

Humidity-control features: Factory-approved combinations of indoor and outdoor units provide wide range of humidity control options.

Additional features: All units receive a functional run test prior to leaving the factory. A full range of EnviroShield condenser coil options are available for corrosion protection.

Contact: Carrier Corporation, Syracuse, NY; Attn: Matt Placito, 315-432-3648; 315-433-4109 (fax); matthew.placito@carrier .utc.com (e-mail); www.carrier.com (website).

eProduct #66

Model: 40 RM/RMQ

Footprint (HxWxL): From 33 x 30 x 47.

Serviceability features: Suction and discharge service valves; semi-hermetic compressor on 7-to 30-ton models; easy access to compressor and controls; multipoise design indoor unit.

Technical support: Carrier Corporation, Customer Relations, P.O. Box 4808, Syracuse, NY 13221; 800-227-7437; contact.carrier@ carrier.utc.com (e-mail).

Noise-reduction features: Not available.

Humidity-control features: Factory-approved combinations of indoor and outdoor units provide wide range of humidity control options.

Additional features: All units receive a functional run test prior to leaving the factory. A full range of EnviroShield condenser coil options are available for corrosion protection.

Contact: Carrier Corporation, Syracuse, NY; Attn: Matt Placito, 315-432-3648; 315-433-4109 (fax); matthew.placito@carrier. utc.com (e-mail); www.carrier.com (website).

eProduct #67

Lennox

Footprint (HxWxL): 35 3/4 x 49 3/4; 35 3/4 x 60 3/8; 59 3/8 x 66 3/4 (dependent on tonnage).

Serviceability features: Manufacturer did not supply.

Technical support: Customer service representatives are avail-able to assist with questions and problems. A toll-free phone number is available for use by Lennox dealers, and technical support is available to the dealers for a 12-hr period, five days a week. Online access to technical information is available to dealers. Training sessions and hands-on troubleshooting assistance is available through field technical consultants.

Noise-reduction features: The unit has scroll compressors on resilient rubber mounts for vibration-free operation, and low outdoor fan speeds for reduced noise levels.

Humidity-control features: Not available.

Additional features: Manufacturer did not supply.

Contact: Lennox, Carrollton, TX; Attn: Commercial Product Platform, Product Marketing; www.lennox.com (website).

eProduct #68

Model: HS 29 split system

Footprint (HxWxL): 35 3/4x 49 3/4; 35 3/4 x 60 3/8; 59 3/8 x 66 3/4 (dependent on tonnage).

Serviceability features: The HS 29 includes enhanced coil guard, slab coils, full perimeter base rails, hinged or slide-out control box, direct-drive fan, service ports, and service valves.

Technical support: Customer service representatives are available to assist with questions and problems. A toll-free phone number is available for use by Lennox dealers, and technical support is available to the dealers for a 12-hr period, five days a week. Online access to technical information is available to dealers. Training sessions and hands-on troubleshooting assistance are available through field technical consultants.

Noise-reduction features: The unit has scroll compressors on resilient rubber mounts for vibration-free operation, and low outdoor fan speeds for reduced noise levels.

Humidity-control features: Not available.

Additional features: The HS 29 has high- and low-pressure switches, compressor crankcase heaters, minimum run time controls, high-capacity filter-drier, service valves, low ambient operation down to 0°F, and optional hot-gas bypass.

Contact: Lennox, Carrollton, TX; Attn: Commercial Product Platform, Product Marketing; www.lennox.com (website).

eProduct #69

United CoolAir

Footprint (HxWxL): Manufacturer did not supply.

Serviceability features: Units are designed for easy and accessible maintenance.

Technical support: Factory service technicians are available to handle troubleshooting.

Noise-reduction features: Manufacturer did not supply.

Humidity-control features: Designed for both comfort cooling and precision (temperature/humidity) control.

Additional features: The evaporators can be split up to 250 ft from indoor condensing unit. Evaporators are sized from 1 to 3 tons, and the condensing unit has up to three individual refrigeration circuits.

Contact: United CoolAir, York, PA; Attn: Jeff Cook, 717-843-4311; 717-854-4462 (fax); uca@unitedcoolair.com (e-mail); www.unitedcoolair.com (website).

eProduct #70

Mars

Footprint (LxH): 42 x 40 (CEV 6000); 62 x 60 (CEV 12,000).

Serviceability features: Access panels for easy access to pump; draw and flow adjustment; manifold is removable for easy cleaning.

Technical support: Full staff of application engineers; 16-hr part shipment program.

Noise-reduction features: Not available.

Humidity-control features: Not available.

Additional features: Capable of airflows up to 12,000 cfm while maintaining as little as 300,000 Btu of heat. In addition, it has a stainless steel cabinet; 12-in. ridged media; and optional fill, drain, and copper manifold. A prefilter is standard.

Contact: Mars Air, Gardena, CA; Attn: Cheryl McGinty, 310-532-1555; 310-324-3030 (fax); marsinfo@marsair.com (e-mail); www.marsair.com (website).

eProduct #71

Friedrich

Footprint (HxWxL): 77 x 45 x 30 1/2.

Serviceability features: All serviceable components are accessible from the front of the unit; service valves are accessed from front of unit.

Technical support: Dealer support, Friedrich Customer Service Department, and customer assurance (post sale).

Noise-reduction features: Fiberglass insulation of all panels; foam gaskets on all removable panels; rubber isolator mount compressor.

Humidity-control features: Not available.

Additional features: Scroll compressor, thermal expansion valve, and high- and low-pressure switches. Free-flow supply plenum gives upflow spot-cooling capabilities.

Contact: Friedrich, San Antonio, TX; Attn: Christine Miller, 800-541-6645, ext. 613; 210-357-4433 (fax); cmiller@friedrich.com (e-mail); www.friedrich.com (website).

eProduct #72

Modine

Footprint (HxWxL): 50 x 68 9/10 x 93 1/2.

Serviceability features: Double-wall construction provides wipe-down surfaces; hinged access panels; local and remote diagnostics; monitor-ing of phase interruption, loss of charge, and coil freeze-up (all standard).

Technical support: Manufacturer did not supply.

Noise-reduction features: Scroll compressors, insulation between double walls.

Humidity-control features: Single-enthalpy and dual-enthalpy economizer options, ERV option.

Additional features: Standard model meets IAQ requirements of ASHRAE 62-1999, which includes ventilation rates and sloped drain pan. Uses the manufacturer’s patented PF™ condensers and evaporators for high latent heat transfer capacity. Has 4- or 2-in. pleated filters; CO2 sensors available; and gas or electric heating option.

Contact: Modine Manufacturing Company Commercial Division, Racine, WI; Attn: Christopher Schroeder, 262-636-1400; 262-636-1800 (fax); c.j.schroeder@modine.com (e-mail); www.modine.com (website).

eProduct #73

Century

Footprint (HxWxD): 72 x 42 x 23.

Serviceability features: Quarter-turn fasteners for quick panel removal.

Technical support: Technical service and troubleshooting available.

Noise-reduction features: 1/2-in. fiberglass insulation.

Humidity-control features: Not available.

Additional features: Special corrosion-resistant construction.

Contact: Century, Jackson, MI; Attn: John Rhoads; www. century-hvac.com (website).

eProduct #74

Comfort-Aire

Footprint (HxWxL): 20 x 36 x 50 (average).

Serviceability features: Manufacturer did not supply.

Technical support: Technical service and troubleshooting are available.

Noise-reduction features: 1/2-in. fiber glass insulation.

Humidity-control features: Not available.

Additional features: Available with copper or cupronickel water coil.

Contact: Comfort-Aire, Jackson, MI; Attn: John Rhoads; www.comfortaire-hvac.com (website).

eProduct #75

Marvair/Airxcel

Footprint (HxWxL): 94 1/2x 43 5/8x 27 5/8.

Serviceability features: All service access, including the compressor, is from the front. Refrigerant valves in the front control box allow easy checking of system pressures. The filter is changeable from the outside.

Technical support: Heat load calculations to determine which unit to use; 24/7 toll-free phone number for service dispatch; nationwide network of service centers; technical and service support by phone and seminars.

Noise-reduction features: High-density insulation; low rpm; quiet condenser fan.

Humidity-control features: Dehumidification is available through optional electric reheat or hot-gas reheat.

Additional features: Both units are built to cool telecommunication shelters. They have all the controls required to operate reliably over a wide range of ambient conditions. The Compac 4 has a factory-built-in economizer for increased reliability and energy savings.

Contact: Marvair/Airxcel, Cordele, GA; Attn: Bill Wilson, 888-726-2734; bwilson@airxcel.com (e-mail); www.marvair.com (website).

eProduct #76

Rheem

Footprint (HxWxL): 44 x 58 3/4 x 93 11/16.

Serviceability features: Hinged access panels; front-access, slide-out blower assembly; convertible airflow for maximum flexibility; side or base utility access minimizing roof penetrations; plug-in electrical connections on outdoor fan assemblies.

Technical support: Technical call center.

Noise-reduction features: Manufacturer did not supply.

Humidity-control features: Not available.

Additional features: One-piece top and base pan on indoor section; aluminized steel heat exchanger helps eliminate corrosion; two-stage gas valve for superior comfort control at minimum operating cost; quiet, efficient, twin Copeland Scroll compressor.

Contact: Rheem Manufacturing, Fort Smith, AR; Attn: Rheem Call Center, 800-548-RHEEM; www.rheemac.com (website).

eProduct #77

International Comfort Products (ICP)

Footprint (HxWxL): 49 x 68 x 117.

Serviceability features: Access panels for easy service; externally mounted gauge ports allow for more accurate reading of operating conditions while servicing.

Technical support: Technical service advisor on staff at local distributor available with technical assistance, troubleshooting; technical training available at ICP National Training Center in La Vergne, TN, and at field schools held in participating distributor locations.

Noise-reduction features: Manufacturer did not supply.

Humidity-control features: Manufacturer did not supply.

Additional features: “No difference” design allows the evaporator blower to deliver the same static capability for either horizontal- or down-discharge applications. High- and low-pressure switches provide compressor protection for extreme cooling operating conditions. Two-stage cooling provides efficient operation during nonpeak periods.

Contact: ICP, Nashville, TN; Attn: John Mott, 800-315-4370; 615-383-2215 (fax); john.mott@mottpr.com (e-mail); www. icpcommercial.com (website).

eProduct #78

Comfortmaker

Footprint (HxWxL): 45-49 x 57-68 x 90-100.

Serviceability features: Access panels for easy service; externally mounted gauge ports provide easy access for maintenance and allow for more accurate reading of operating conditions while servicing.

Technical support: Technical service advisor on staff at local distributor available with technical assistance and troubleshooting; technical training available at ICP National Training Center in La Vergne, TN, and at field schools held in participating distributor locations.

Noise-reduction features: Manufacturer did not supply.

Humidity-control features: Manufacturer did not supply.

Additional features: “No difference” design allows the evaporator blower to deliver the same static capability for either horizontal- or down-discharge applications. Two-stage cooling provides efficient operation during nonpeak periods. High- and low-pressure switches provide compressor protection for extreme cooling operating conditions. Designed for slide-in, plug-in economizer installation.

Contact: Comfortmaker, Nashville, TN; Attn: John Mott, 800-315-4370; 615-383-2215 (fax); john.mott@mottpr.com (e-mail); www.comfortmaker.com (website).

eProduct #79

Arcoaire

Footprint (HxWxD): 421¼2 x 33 x 35.

Serviceability features: Externally mounted gauge ports provide easy access for maintenance and allow for more accurate reading of operating conditions while servicing. Service valves are on all models with 31¼2-in. stubs; there is also a fan motor inline disconnect plug. Access panels for easy service.

Technical support: Technical service advisor on staff at local distributor available with technical assistance and troubleshooting; technical training available at ICP National Training Center in La Vergne, TN, and at field schools held in participating distributor locations.

Noise-reduction features: Manufacturer did not supply.

Humidity-control features: Manufacturer did not supply.

Additional features: New top-discharge design has a corrosion-resistant grille. High- and low-pressure switches provide compressor protection for extreme cooling operating conditions. Two-stage cooling provides efficient operation during nonpeak periods.

Contact: Arcoaire, Nashville, TN; Attn: John Mott, 800-315-4370; 615-383-2215 (fax); john.mott@mottpr.com (e-mail); www.arcoaire.com (website).

eProduct #80

Tempstar

Footprint (HxWxL): 36 x 48 x 73.

Serviceability features: Access panels for easy service; externally mounted gauge ports provide easy access for maintenance, and allow for more accurate reading of operating conditions while servicing.

Technical support: Technical service advisor on staff at local distributor available with technical assistance and troubleshooting; technical training available at ICP National Training Center in La Vergne, TN, and at field schools held in participating distributor locations.

Noise-reduction features: Manufacturer did not supply.

Humidity-control features: Manufacturer did not supply.

Additional features: “No difference” design allows the evaporator blower to deliver the same static capability for either horizontal- or down-discharge applications. Designed for slide-in, plug-in economizer installation. High- and low-pressure switches provide compressor protection for extreme cooling operating conditions.

Contact: Tempstar, Nashville, TN; Attn: John Mott, 800-315-4370; 615-383-2215 (fax); john.mott@mottpr.com (e-mail); www.tempstar.com (website).

eProduct #81

Heil

Footprint (HxWxD): 42 1/2x 33 x 35.

Serviceability features: Access panels for easy service; externally mounted gauge port allows for more accurate reading of operating con-ditions while servicing and easy access for maintenance. Service valves are on all models with 3 1/2-in. stubs; there also is a fan motor inline disconnect plug.

Technical support: Technical service advisor on staff at local distributor available with technical assistance and troubleshooting; technical training available at ICP National Training Center in La Vergne, TN, and at field schools held in participating distributor locations.

Noise-reduction features: Manufacturer did not supply.

Humidity-control features: Manufacturer did not supply.

Additional features: New top-discharge design has a corrosion-resistant grille. High- and low-pressure switches provide compressor protection for extreme cooling operating conditions. Two-stage cooling provides efficient operation during nonpeak periods.

Contact: Heil, Nashville, TN; Attn: John Mott, 800-315-4370; 615-383-2215 (fax); john.mott@mottpr.com (e-mail); www.heil-hvac.com (website).

eProduct #82

Bryant

Footprint (HxWxL): 33 5/16 x 45 x 73 11/16; 41 5/16 x 57 3/4 x 87 3/8; 49 5/16 x 57 3/4 x 87 3/8 (dependent on model tonnage).

Serviceability features: Optional factory-installed hinged access panels; 115-V convenience outlet; and nonfused disconnect switch.

Technical support: Service through national network of Bryant distributors and dealers. Dealer locator at www.bryant.com, and 888-999-BRYANT.

Noise-reduction features: Quiet operation with ARI sound ratings down to 76 dB.

Humidity-control features: Bryant’s “Perfect Humidity System” for rooftops is a dehumidification package that features an additional subcooler coil that removes even more moisture from the air, enhancing comfort and IAQ. When paired with Bryant’s light commercial Thermidistat, temperature setpoints and humidity can be controlled from one panel.

Additional features: Optional, factory-installed features include a high-static-pressure blower in addition to the alternate belt-drive blower; optional hinged access panels for even greater ease of service; 115-V convenience outlet and a nonfused disconnect switch; four levels of corrosion-resistant coils.

Contact: Bryant Heating & Cooling, Indianapolis, IN; Attn: Doug Masch, 317-240-5265; 317-240-5666 (fax); doug.masch@ bryant.com (e-mail); www.bryant.com (website).

eProduct #83

Model: 581B

Footprint (HxWxL): 33 5/16x 45 x 73 11/16; 41 5/16 x 57 3/4x 87 3/8; 49 5/16 x 57 3/4 x 87 3/8 (dependent on model tonnage).

Serviceability features: Optional factory-installed hinged access panels; 115-V convenience outlet; and nonfused disconnect switch.

Technical support: Service through national network of Bryant distributors and dealers. Dealer locator at www.bryant.com, and 888-999-BRYANT.

Noise-reduction features: Quiet operation with ARI sound ratings down to 76 dB.

Humidity-control features: Bryant’s “Perfect Humidity System” for rooftops is a dehumidification package that features an additional subcooler coil that removes even more moisture from the air, enhancing comfort and IAQ. When paired with Bryant’s light commercial Thermidistat, temperature setpoints and humidity can be controlled from one panel.

Additional features: Optional, factory-installed features include a high-static-pressure blower in addition to the alternate belt-drive blower; optional hinged access panels for even greater ease of service; 115-V convenience outlet and a nonfused disconnect switch; four levels of corrosion-resistant coils.

Contact: Bryant Heating & Cooling, Indianapolis, IN; Attn: Doug Masch, 317-240-5265; 317-240-5666 (fax); doug.masch@ bryant.com (e-mail); www.bryant.com (website).

eProduct #84

Robur

Footprint (HxWxL): 49 x 93 to 49 x 246 (varies by model).

Serviceability features: Microprocessor with LED readout to assist with installation, service, and diagnostics.

Technical support: Trained, certified dealers in the field; toll-free factory and technical assistance.

Noise-reduction features: Not available; sound levels are 54 to 58 dB.

Humidity-control features: Not available.

Additional features: Factory staging controls provided; single-phase 208/230-V operation; single-point connections for gas, water, and electricity.

Contact: Robur, Evansville, IN; Attn: Jennifer Thacker, 812-424-1800; 812-424-5117 (fax); robur@robur.com (e-mail); www.robur .com (website).

eProduct #85

Frigidaire

Footprint (HxWxL): 44 1/4x 37 1/2 x 37 1/2.

Serviceability features: Brass base valves for service; high- and low-pressure switches; suction accumulator; a liquid-line filter-drier; 5-min restart time delay; and plastic mesh hail guard.

Technical support: 800 number for distributor and/or contractor.

Noise-reduction features: Not available.

Humidity-control features: Manufacturer did not supply.

Additional features: Manufacturer did not supply.

Contact: Nordyne, O’Fallon, MO; Attn: David Garvin, 636-561-7365; garvind@nordyne.com (e-mail); www.nordyne.com (website).

eProduct #86

Tappan

Footprint (HxWxL): 44 1/4 x 37 1/2 x 37 1/2.

Serviceability features: Brass base valves for service; high- and low-pressure switches; suction accumulator; a liquid-line filter-drier; 5-min restart time delay; and plastic mesh hail guard.

Technical support: 800 number for distributor and/or contractor.

Noise-reduction features: Not available.

Humidity-control features: Manufacturer did not supply.

Additional features: Manufacturer did not supply.

Contact: Nordyne, O’Fallon, MO; Attn: David Garvin, 636-561-7365; garvind@nordyne.com (e-mail); www.nordyne.com (website).

eProduct #87

Kelvinator

Footprint (HxWxL): 44 ¼ x 37 ½ x 37 ¼ .

Serviceability features: Brass base valves for service; high- and low-pressure switches; suction accumulator; a liquid-line filter-drier; 5-min restart time delay; and plastic mesh hail guard.

Technical support: 800 number for distributor and/or contractor.

Noise-reduction features: Not available.

Humidity-control features: Manufacturer did not supply.

Additional features: Manufacturer did not supply.

Contact: Nordyne, O’Fallon, MO; Attn: David Garvin, 636-561-7365; garvind@nordyne.com (e-mail); www.nordyne.com (website).

eProduct #88

Philco

Footprint (HxWxL): 44 ¼ x 37 ½ x 37 ½ .

Serviceability features: Brass base valves for service; high and low pressure switches; suction accumulator; a liquid-line filter-drier; 5-min restart time delay; and plastic mesh hail guard.

Technical support: 800 number for distributor and/or contractor.

Noise-reduction features: Not available.

Humidity-control features: Manufacturer did not supply.

Additional features: Manufacturer did not supply.

Contact: Nordyne, O’Fallon, MO; Attn: David Garvin, 636-561-7365; garvind@nordyne.com (e-mail); www.nordyne.com (website).

eProduct #89

Reznor

Footprint (HxWxL): 70 x 44 (to 57) x 189 (to 215).

Serviceability features: Service gauge ports; dedicated filter section; drainable condensate pans; standard electromechanical parts.

Technical support: Manufacturer did not supply.

Noise-reduction features: Manufacturer did not supply.

Humidity-control features: Dedicated dehumidifier section.

Additional features: Manufacturer did not supply.

Contact: Thomas & Betts, Memphis, TN; Attn: John Garavelli, 901-252-5000, ext. 5177; 901-252-1305 (fax); john_garavelli@ tnb.com (e-mail); www.ReznorOnline.com (website).

eProduct #90

Model: PCDA

Footprint (HxWxL): 70 x 44 (to 57) x 189 (to 215).

Serviceability features: Service gauge ports; dedicated filter section; drainable condensate pans; standard electromechanical parts.

Technical support: Manufacturer did not supply.

Noise-reduction features: Manufacturer did not supply.

Humidity-control features: Dedicated dehumidifier section.

Additional features: Manufacturer did not supply.

Contact: Thomas & Betts, Memphis, TN; Attn: John Garavelli, 901-252-5000, ext. 5177; 901-252-1305 (fax); john_garavelli@tnb.com (e-mail); www.ReznorOnline.com (website).

eProduct #91

Publication Date: 04/09/2001