In addition to the 2009 Residential Heating Showcase product grid (see the PDF link at the bottom of this article),The NEWSis spotlighting the industry’s latest residential heating products in the following photo feature. The manufacturers provided us with the brief description of features included with each product. For more information, please contact the manufacturers or their distributors.
ADP
Model:FOA Series separated combustion unit heaterFootprint (inches):Manufacturer did not specify.
Serviceability features:Manufacturer did not specify.
Technical support:Manufacturer did not specify.
Technical support materials:Manufacturer did not specify.
Noise-reduction features:Manufacturer did not specify.
IAQ equipment supported:Manufacturer did not specify.
Thermostat compatibility:Manufacturer did not specify.
Additional features:Separated combustion.
Warranty information:Two-year standard limited all parts; 10-year standard limited heat exchanger.
Special installation requirements:Manufacturer did not specify.
Contact:Advanced Distributor Products (ADP), Stone Mountain, Ga.; attn: Heena Mohamed, 770-465-5569; 770-465-5599 (fax); heena.mohamed@adpnow.com; www.adpnow.com.
eProduct 160
Footprint (inches):Manufacturer did not specify.
Serviceability features:Manufacturer did not specify.
Technical support:Manufacturer did not specify.
Technical support materials:Manufacturer did not specify.
Noise-reduction features:Manufacturer did not specify.
IAQ equipment supported:Visit Website for details.
Thermostat compatibility:Manufacturer did not specify.
Replacement parts compatibility:Some shared parts, some unique.
Additional features:Manufacturer did not specify.
Warranty information:Two-year standard limited all parts; 10-year standard limited aluminized steel heat exchanger; 15-year standard limited stainless steel heat exchanger.
Special installation requirements:Manufacturer did not specify.
Contact:Advanced Distributor Products (ADP), Stone Mountain, Ga.; attn: Heena Mohamed, 770-465-5569; 770-465-5599 (fax); heena.mohamed@adpnow.com; www.adpnow.com.
eProduct 161
Allied Air Enterprises
Model:MGE4 Series through-the-wall unitFootprint (inches):24 (length) by 28 (width) by 58, 60, and 64 (height)
Serviceability features:Features include suction and liquid line service ports; low-maintenance, permanently sealed motors; and self diagnostics included in the integrated furnace control.
Technical support:For field support, call 866-282-7257 8 a.m.-5 p.m. Eastern.
Technical support materials:Wiring diagrams, spec sheets, and installation instructions are available.
Noise-reduction features:Insulated blower compartment, multiblade condenser fan to reduce air noise, and a condenser section lined with noise reducing fiberboard.
IAQ equipment supported:Washable filters are shipped with the unit. Add-on accessories such as humidifiers can be installed separately.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:Through-the-wall unit design provides the multifamily industry with low product lifecycle costs. Installation requirements are minimal, and a wide variety of outdoor louver colors blend in with building decors.
Warranty information:Standard warranty includes five-year parts, 10-year aluminized heat exchanger, and 20-year stainless steel heat exchanger. Extended warranties are available.
Special installation requirements:Units are shipped prewired and precharged from the factory. Wall sleeves, exterior louvers, and other accessories can be ordered separately. Typical installation locations include mechanical rooms and closets along outside walls.
Contact:Allied Air Enterprises, West Columbia, S.C.; attn: George Groh, 803-738-4060; 803-738-4001 (fax); george.groh@alliedair.com; www.magic-pak.com.
eProduct 162
Footprint (inches):22, 25 (length) by 28 (width) by 44, 48, 56 (height)
Serviceability features:Features include suction and liquid line service ports, low maintenance permanently sealed motors, and self diagnostics included in the integrated furnace control.
Technical support:For field support, call 866-282-7257. Hours of operation are 8 a.m.-5 p.m. Eastern.
Technical support materials:Wiring diagrams, spec sheets, and installation instructions are available.
Noise-reduction features:Insulated blower compartment, multiblade condenser fan to reduce air noise, and a condenser section lined with noise reducing fiberboard.
IAQ equipment supported:Washable filters are shipped with the unit. Add-on accessories such as humidifiers can be installed separately.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:Through-the wall unit design provides the multifamily industry with low product life cycle costs. Installation requirements are minimal, and a wide variety of outdoor louver colors blend in with any building decor.
Warranty information:Standard warranty includes five-years parts. Extended warranties are available.
Special installation requirements:Units are shipped prewired and precharged from the factory. Wall sleeves, exterior louvers, and other accessories can be ordered separately. Typical installation locations include mechanical rooms and closets along outside walls.
Contact:Allied Air Enterprises, West Columbia, S.C.; attn: George Groh, 803-738-4060; 803-738-4001 (fax); george.groh@alliedair.com; http://www.magic-pak.com.
eProduct 163
Amana
Model:AMV9 gas furnaceFootprint (inches):28 (length) by 17.5 (width) by 40 (height)
Serviceability features:Easier-to-install top venting is standard; alternate flue/vent locations available, two-stage gas valve operates on two-stage or single-stage thermostats, furnace control board with self-diagnostics, color-coded low-voltage terminals and provisions for electronic air cleaners and 120- or 24-V humidifiers, convenient left or right connection for gas/electric service.
Technical support:Technical support is available from local distributors, factory field representatives, and by calling Amana brand technical support at 888-593-9988.
Technical support materials:Wiring diagrams, service/troubleshooting information, installation data, parts and part numbers are immediately available to all installing contractors via the local distributor or they can be downloaded online from Partner Link at www.amana-hac.com.
Noise-reduction features:Fully insulated, heavy-gauge steel cabinet, quiet two-speed induced-draft motor, variable-speed blower motor, SureStart ignition.
IAQ equipment supported:Fully compatible with all IAQ enhancement components and systems.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Some shared parts, some unique.
Additional features:Patented Million-Air™ stainless steel, dual-diameter tubular heat exchanger has successfully cycled over 2 million times without failure and continues to cycle right now in our testing laboratory. Dual certified for sealed combustion direct vent or nondirect vent applications. Two-stage gas valve operates with two-stage or single-stage thermostats. Auto-comfort and enhanced dehumidification modes provide energy savings and additional comfort during cooling mode.
Warranty information:Covered by a lifetime unit replacement limited warranty: Should the heat exchanger ever fail to the original registered homeowner, a new unit will be provided at no charge. All functional parts are covered by 10-year parts limited warranty. Online registration is required within 60 days of installation for both warranties. Online registration is not required in California or Quebec. Full warranty details are available online.
Special installation requirements:Designed for multiposition installation (upflow, horizontal left or right). Airtight, solid bottom for side-return applications and easier-cut tabs for removal in bottom air-inlet applications. Convenient left or right connection for gas and electric service.
Contact:Goodman Global Inc., Houston; attn: Rex Anderson, 713-263-5064; 713-586-8059 (fax); rex.anderson@goodmanmfg.com; www.amana-hac.com.
eProduct 164
Footprint (inches):36 (length) by 36 (width) by 38 (height)
Serviceability features:Copeland ComfortAlert diagnostics; sweat-connection service valves with easier-access gauge ports; top and side maintenance access; single-panel access to controls and space for field-installed accessories; factory-installed, biflow, liquid-line filter-drier.
Technical support:Technical support available from local distributors, factory field representatives, and by calling brand technical support at 888-593-9988.
Technical support materials:Wiring diagrams, service/troubleshooting information, installation data, parts data, and part numbers are available to installing contractors via the local distributor, or they can be downloaded online from Partner Link via the Website.
Noise-reduction features:High-density foam compressor cover, efficient and quiet condenser fan motor, and sound-control top design.
IAQ equipment supported:Fully compatible with all IAQ enhancement components and systems.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:Offers efficiency levels and operating sound levels that are among the best in the HVAC industry. Quality manufacturing and easier installation and maintenance make this unit one of the best premium products available, the company says.
Warranty information:Covered by a lifetime unit replacement limited warranty to the original registered homeowner. Should the compressor fail, a new unit will be provided at no cost. All functional parts are covered by a 10-year parts limited warranty. To receive both warranties, online registration must be completed within 60 days of installation (online registration not required in California or Quebec). Full warranty details available online.
Special installation requirements:Factory-installed, biflow, liquid-line filter-drier; R-410A refrigerant; sweat connection service valves; liquid-line return protection; rust-resistant coated screws.
Contact:Goodman Global, Inc., Houston; attn: Rex Anderson, 713-263-5064; 713-586-8059 (fax); rex.anderson@goodmanmfg.com; www.amana-hac.com.
eProduct 165
Amcoraire
Model:AMS181HX ductless mini-splitFootprint (inches):12 (length) by 45 (width) by 15 (height)
Serviceability features:Advanced inverter technology features low-ambient operation to -4°F. Unit comes standard with a wireless remote and a wired controller. Clean styling uses LCD for temperature and functions.
Technical support:Available 9 a.m.-5 p.m. Eastern at 201-460-8100 or by e-mail (don@amcorgroupusa.com).
Technical support materials:Available online.
Noise-reduction features:Compressor insulation.
IAQ equipment supported:Manufacturer did not specify.Thermostat compatibility:Requires a special thermostat (supplied).
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:Largest ductless single-zone, mini-split to qualify for tax credit. Fresh look with LCD for temperature and function; 18 SEER efficiency, low-ambient operation to -4°F.
Warranty information:Three-years parts, no-hassle free exchange, five-years compressor, one-year limited labor.
Special installation requirements:Installation kit includes 25-foot copper tubing, 25-foot connecting wire.
Contact:Amcor Inc., Carlstadt, N.J.; attn: Mark O’Donnell, 201-460-8100; 866-886-4164 (fax); mark@amcorgroupusa.com; www.amcorgroupusa.com.
eProduct 166
American Standard Heating and Air Conditioning
Model:Freedom 95 single-stage gas furnace (AUH1)Footprint (inches):28 (length) by 18-25 (width) by 40 (height)
Serviceability features:Quarter-turn blower door latches on upflow models; self-diagnostic controls.
Technical support:Dedicated local technical support.
Technical support materials:Please contact the distributor.
Noise-reduction features:Solid burner door, heavy-steel insulated cabinet, sound-insulated blower compartment.
IAQ equipment supported:Unit can be matched with an AccuClean™ whole-home air filtration system to remove up to 99.98 percent of unwanted particles and allergens from filtered indoor air.
Thermostat compatibility:Compatible with most thermostats.Replacement parts compatibility:Shares replacement parts with other models.
Additional features:This high-efficiency, entry-level furnace qualifies for the federal energy tax credit. Its exclusively designed, integrated system control provides total control of limit sensors, blowers, gas valve, and flame control, and includes self diagnostics for service. An adaptive hot-surface silicon nitride igniter prevents overheating, resulting in reliable ignition.
Warranty information:Registered limited liability warranty terms include a lifetime limited warranty on heat exchanger and a five-years limited warranty on functional parts. Optional extended warranties are available.
Special installation requirements:None.
Contact:American Standard Heating and Air Conditioning, Tyler, Texas; attn: Christy Lee; christy.lee@americanstandardair.com; www.americanstandardair.com.
eProduct 167
Footprint (inches):34 (length) by 37 (width) by 33-45 (height)
Serviceability features:Features easier access cabinet, service access and refrigerant connections with full coil protection.
Technical support:Dedicated local technical support available.
Technical support materials:Contact distributor for more information.
Noise-reduction features:Compressor sound insulator to reduce sound.
IAQ equipment supported:When installed as part of a complete American Standard Heating and Air Conditioning system, this unit can be matched with an AccuClean Whole-Home Air Filtration System to remove up to 99.98 percent of unwanted particles and allergens from filtered indoor air.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:This is a high efficiency mid-level option with system combinations that qualify for the energy tax credit. It also features a Duration™ compressor and a Spine Fin™ coil, which preserves greater heat transfer capabilities and more efficiency over time.
Warranty information:Registered limited warranty terms (10-year limited compressor, 10-year limited outdoor coil, 10-year limited internal functional parts). Optional extended warranties available.
Special installation requirements:Manufacturer did not specify.
Contact:American Standard Heating and Air Conditioning, Tyler, Texas; attn: Christy Lee; christy.lee@americanstandardair.com; www.americanstandardair.com.
eProduct 168
Arcoaire
Model:PGD4 package gas/electric unitFootprint (inches):33-44 (length) by 48 (width) by 40-54 (height)
Serviceability features:Three separate service panels, clearly marked with embossed symbols, offer access to the compressor, blower compartment, and control box. Service techs can keep the unit on while running diagnostics, since they can have one panel open with others closed.
Technical support:In an effort to be as responsive as possible, Factory-trained Technical Service Advisors (TSAs) on staff at local distributors provide technical assistance, troubleshooting at the local level.
Technical support materials:Product information posted online at Arcoaire dealer Website www.goarcoaire.com includes product spec sheets, installation-operation manuals, and technical support/parts manuals. Technical support materials are also available from local distributors.
Noise-reduction features:Quieter operation is a result of additional stability provided by newly designed, formed top panel.
IAQ equipment supported:Dehumidification cooling speed standard on control board. Internal filter kits available as accessories.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:Eligible for the 2009-2010 U.S. HVAC tax credit for efficient fans. Compact units fit in bed of standard pick-up truck. Full perimeter steel base rails give units extra stability and make them easier to load and transport. High efficiency X-13 indoor blower motor delivers efficient airflow. Hail guard standard on all models.
Warranty information:15-year limited on heat exchangers; 10-year parts limited with timely registration (restrictions apply; see warranty certificate for details). To learn more about all of these limited warranties, go to www.goarcoaire.com and click on the “Warranty” tab on the menu.
Special installation requirements:Metal base rails for simplified rigging (roof installations).
Contact:International Comfort Products (ICP), LLC, Nashville, Tenn.; attn: John Mott, 800-315-4370; 615-383-2215 (fax); john.mott@mottpr.com; www.goarcoaire.com.
eProduct 169
Footprint (inches):29 (length) by 19-25 (width) by 40 (height)
Serviceability features:Designed with easier-to-remove doors and extra-spacious service compartments to give techs room to work. Includes a built-in electronic diagnostic system that can be used even while the furnace is running. Most hose and clamp connections are premade by the factory, substantially reducing installation time.
Technical support:In an effort to be as responsive as possible, Factory-trained Technical Service Advisors (TSAs) on staff at local distributors provide technical assistance, troubleshooting at the local level.
Technical support materials:Product information posted online at Arcoaire dealer Website www.goarcoaire.com includes product spec sheets, installation-operation manuals, and technical support/parts manuals. Technical support materials are also available from local distributors.
Noise-reduction features:Solid doors provide a sealed combustion compartment for quiet operation. The unit has two-stage heating, which means it operates in the quieter first stage 70-80 percent of the time. The one-piece steel cabinet is thermal-lined and an insulated blower compartment provides added sound protection.
IAQ equipment supported:Predrilled accessory holes and convenient wiring hook-ups make it easier to add humidifiers, electronic air cleaners and other accessories.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:Eligible for the 2009-2010 U.S. HVAC tax credit. Four-position furnace provides maximum efficiency, quiet operation, and premium comfort of variable-speed, two-stage heating. Meets California low NOx emissions standards. Variable-speed blower motor cuts electricity costs. Equipped with long-lasting silicon nitride igniters. One- or two-pipe venting. Easier-view troubleshooting LED fault indicator.
Warranty information:Ten-years No Hassle Replacement™ limited warranty; lifetime limited heat exchangers; 10-year parts limited with timely registration (restrictions apply; see warranty certificate for details). To learn more about all of these limited warranties, go to www.goarcoaire.com and click on the “Warranty” tab on the menu.
Special installation requirements:Shipped as natural gas in upflow configuration, with all parts included for downflow, horizontal-left and right with no need for accessory conversion kits. LP gas kits available.
Contact:International Comfort Products (ICP), LLC, Nashville, Tenn.; attn: John Mott, 800-315-4370; 615-383-2215 (fax); john.mott@mottpr.com; www.goarcoaire.com.
eProduct 170
Bard
Model:GeoTec geothermal heat pumpFootprint (inches):26 or 27 (length) by 28 or 33 (width) by 48 or 56 (height)
Serviceability features:Features two-stage step capacity scroll compressor, R-410A green refrigerant, and variable-speed ECM motor for superior efficiencies and quiet performance. Increased dealer friendly installation and service features include left or right side water connections outside of cabinet, left- or right-hand access to control panel, slide-in electric heat packages, and simplified wiring and troubleshooting.
Technical support:In-house and field training classes available. Service provided through distribution network.
Technical support materials:Service parts guides, wiring diagrams, installation manuals, (printed and digital formats), Website.
Noise-reduction features:Copeland scroll step capacity compressor, variable-speed ECM blower motor designed for soft start up, compressor/service compartment insulated to reduce noise levels.
IAQ equipment supported:Compatible with field installed electronic air cleaner or high efficiency media type filters through the installing dealers.
Thermostat compatibility:Compatible with most thermostats.Replacement parts compatibility:Shares replacement parts with other models.
Additional features:Suitable for ground water or ground loop applications. Features multicapacity two-stage compressor, variable-speed ECM blower motor, R-410A refrigerant, Energy Star efficiency rating, built-in domestic hot water heat exchanger, COP ratings up to 5.4, and EER ratings up to 30.6.
Warranty information:Five-years parts, 10-year compressor.
Special installation requirements:None.
Contact:Bard Manufacturing Co., Inc., Bryan, Ohio; attn: Bill Steel, 419-636-1194; 419-636-2640 (fax); bard@bardhvac.com; www.bardhvac.com.
eProduct 171
Broan
Model:FG7T iSeer furnaceFootprint (inches):Manufacturer did not specify.
Serviceability features:Color-coded wire harness is designed to fit the components, all with quick-connect fittings for ease of service and replacement. Flexible category IV venting system may be vertically or horizontally vented using either a one-pipe or two-pipe system for maximum flexibility in installation. Diagnostic lights for easier troubleshooting without counting flashes. A dedicated light for flame signal strength and two lights in combination indicate all other fault codes with easier-to-recognize stats without counting flashes. Integrated control board includes connections for electronic air cleaner, and humidifier. Two-piece door design uses captured screws to prevent losing door screws.
Technical support:Available at 800-422-4328, Monday-Friday, 8 a.m.-4:30 p.m. Central.
Technical support materials:Technical specs and installation guides available 24/7 on literature library at www.nordyne.com.
Noise-reduction features:Sealed blower compartment door reduces air leakage and it’s insulated for quiet operation.IAQ equipment supported:Two-stage, variable-speed technology allows furnace to run longer at lower speeds for a more uniform, comfortable mix of air and better filtration.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:Furnace includes iSEER, an energy-efficient brushless DC (ECM) motor that gives up to a 1-SEER-point efficiency gain in cooling. Its low height makes it easier to install in low-ceiling applications, works well with taller high-SEER coils, is easier to handle and install.
Warranty information:With product registration, 10-year parts and 10-year Quality Pledge to replace the entire unit if the heat exchanger fails.
Special installation requirements:None.
Contact:Nordyne, O’Fallon, Mo.; attn: Matt Lattanzi, 800-422-4328; 636-561-7399 (fax); res_sales@nordyne.com; www.broanhvac.net.
eProduct 172
Footprint (inches):49 (length) by 35 (width) by 30 (height)
Serviceability features:The service valves are accessible and simplify servicing of the refrigeration system. For contractors, access panels are provided to all major components and the compressor; 0-inch clearance to combustibles on duct side of the unit allows for installations in tight areas. Easier access to evaporator for cleaning and general maintenance.
Technical support:Available at 800-422-4328, Monday-Friday, 8 a.m.-4:30 p.m. Central.
Technical support materials:Technical specs and installation guides available 24/7 on literature library at www.nordyne.com.
Noise-reduction features:Quiet operation and low vibration; 20-inch fan blade combined with custom venturi condenser fan. Compressor sound blanket standard.
IAQ equipment supported:Manufacturer did not specify.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:Compact footprint and profile make the model easier to install and transport. Standard demand defrost provides additional energy savings in heating by defrosting only when necessary. Three-minute restart time delay after unit shuts down, eliminating the highest cause for compressor failure.
Warranty information:With product registration, 10-year parts and 10-year Quality Pledge to replace the entire unit if the compressor or heat exchanger fails.
Special installation requirements:None.
Contact:Nordyne, O’Fallon, Mo.; attn: Dave Garvin, 800-422-4328; 636-561-7399 (fax); res_sales@nordyne.com; www.broanhvac.net.
eProduct 173
Bryant
Model:Legacy™ 359AAV furnaceFootprint (inches):29 (length) by 19-25 (width) by 40 (height)
Serviceability features:Electronic controls provide system monitoring and comfort control, while providing service techs time-saving diagnostic capabilities.
Technical support:Solution Center is available at 888-999-7237 or solutioncenter@bryant.com.
Technical support materials:Service and troubleshooting information; full installation kit, including diagrams, installation manual, product data sheets.
Noise-reduction features:Steel cabinet construction, insulation, a multispeed blower motor, and induced-draft operation contribute to quiet operation.
IAQ equipment supported:Compatible with indoor air filtration upgrades.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:Patented primary heat exchanger, as well as a stainless steel secondary heat exchanger, transfer an additional 11-15 percent of available heat into the home.
Warranty information:To the original owner, the furnace is covered by a 10-year parts limited warranty upon timely registration of the new equipment. (Warranty period is five-years parts limited if not registered within 90 days. Jurisdictions where warranty benefits cannot be conditioned on registration automatically receive a 10-year parts limited warranty. See warranty certificate at bryant.com. for details.) The heat exchangers are protected by a 20-year limited parts warranty. Extended warranties may include labor.
Special installation requirements:Manufacturer did not specify.
Contact:Bryant, Indianapolis; attn: Bryant Solution Center, 888-994-7237; solutioncenter@bryant.com; www.bryant.com.
eProduct 174
Carrier
Model:Comfort™ 58HDX furnaceFootprint (inches):29 (length) by 19-25 (width) by 40 (height)
Serviceability features:Servicing is convenient with a door designed for easier access. The unit features LED self diagnostics and nonvolatile fault code memory. An electronic control monitors system operation for comfort and provides the installing tech time-saving diagnostics. The entire blower assembly is mounted on rails allowing for easier service of the blower assembly.
Technical support:Expert Central is available at 800-946-2930 or expert.central.carrier.com.
Technical support materials:Service/troubleshooting information, full installation kit includes diagrams, installation manual, product data sheets.
Noise-reduction features:The cabinet design helps ensure quieter operation with two doors and an insulated cabinet.
IAQ equipment supported:Compatible with upgraded air filtration for improved IAQ.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:The PowerHeat™ igniter is a robust and durable ignition system. It replaces a pilot light for enhanced reliability and reduced energy consumption.
Warranty information:To the original owner, the furnace is covered by a 10-year-parts limited warranty upon timely registration of the new equipment. (Warranty period is five-years parts limited if not registered within 90 days. Jurisdictions where warranty benefits cannot be conditioned on registration automatically receive a 10-year parts limited warranty. See warranty certificate at carrier.com. for complete details.) The heat exchangers are covered by a 20-year-parts limited warranty. Extended warranties may include labor.
Special installation requirements:Manufacturer did not specify.
Contact:Carrier Corp., Indianapolis; attn: Expert Central, 800-946-2930; expert.central@carrier.com; www.carrier.com.
eProduct 175
Cayenne Unit Heaters
Model:FSA unit heaterFootprint (inches):Manufacturer did not specify.
Serviceability features:Manufacturer did not specify.
Technical support:Manufacturer did not specify.
Technical support materials:Manufacturer did not specify.
Noise-reduction features:Manufacturer did not specify.
IAQ equipment supported:Visit www.adpnow.com.
Thermostat compatibility:Manufacturer did not specify.
Replacement parts compatibility:Some shared parts, some unique.
Additional features:Manufacturer did not specify.
Warranty information:Two-year standard limited all parts, 10-year standard limited heat exchanger.
Special installation requirements:Manufacturer did not specify.
Contact:Advanced Distributor Products, Stone Mountain, Ga.; attn: Heena Mohamed, 770-465-5569; 770-465-5599 (fax); heena.mohamed@adpnow.com; www.adpnow.com.
eProduct 176
Century
Model:GeoMax2 HTV070 geothermal heat pumpFootprint (inches):31 (length) by 25 (width) by 59 (height)
Serviceability features:Removable panels on three sides provide access to components. Service valves are built in. CMS controls with LED status light have memory feature for diagnosis. Drop-out blower assembly and bidirectional thermal expansion valve add to serviceability.
Technical support:Available at 517-787-2100 8 a.m.-5 p.m. Eastern, weekdays.
Technical support materials:IOM includes wiring diagrams and troubleshooting guide, plus parts list; can be e-mailed as PDFs or sent as hard copies; also available online to authorized distributors. Design Engineering Guide for spec purposes also available. Multiple safeties protect the unit from damage resulting from high or low pressures, loss of charge, condensate overflow, and more.
Noise-reduction features:Double-isolated compressor mounting and vibration isolation springs minimize vibrational sound. Insulated compressor and air handler compartments dampen noise. Low-RPM blower and soft-start blower motor also contribute.
IAQ equipment supported:Two-stage design means the unit runs continuously (mostly at part load), so air continuously passes across the filter. Also, continuous operation helps maintain a comfortable humidity level.
Thermostat compatibility:Compatible with most thermostats. Two-stage thermostat recommended.
Replacement parts compatibility:Some shared parts, some unique.
Additional features:Full-load/part-load switching eliminates on-off cycling, maximizes efficiency. Performance Monitoring System signals potential problems so maintenance can be scheduled. Variable-speed ECM blower motor automatically adapts to all applications and can help overcome ductwork static pressure. Two-stage compressor adds to efficiency. Domestic hot water generator with built-in pump is standard.
Warranty information:Twelve-years limited compressor, six-year limited parts (some limitations apply - see complete warranty on Website for details). AssurancePlus™ extended service agreements available.
Special installation requirements:Comes with factory-installed TXV. Geothermal piping field required.
Contact:Century, Jackson, Mich.; attn: Robert Sycks, Director of Sales CAC; 517-787-2100; 517-787-9341 (fax); info@heatcontroller.com; www.century-hvac.com.
eProduct 177
Footprint (inches):24-32 (length) by 24-32 (width) by 26-35 (height)
Serviceability features:Three service ports (liquid, vapor and common) are easily accessed. Waterproof control box is located above service port. Discharge fan assembly is removed for access to components.
Technical support:Available at 517-787-2100, 8 a.m.-5 p.m. Eastern, weekdays.
Technical support materials:Installation manual with troubleshooting guide and wiring diagrams, owner use and care manual, and parts list can be e-mailed as PDFs or sent as hard copies; also available online to authorized distributors.
Noise-reduction features:Top fan discharge, muffler on compressor, and noncycling reversing valve all minimize operational sound; heavy-duty grille and motor mount also prevent vibration for reduced operational sound.
IAQ equipment supported:Manufacturer did not specify.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Some shared parts, some unique.
Additional features:Demand defrost improves efficiency by defrosting only when needed; full metal louvered jacket protects the coil; copper coils with enhanced aluminum fins provide maximum surface for heat exchange; expansion valve with interior check valve adds reliability; matte finish on steel cabinet is durable; outstanding warranty coverage.Warranty information:Twelve-years compressor and 12-year parts (with registration by original owner within 90 days of purchase; other limitations apply - see warranty on Website for details). AssurancePlus extended service agreements available.
Special installation requirements:Bidirectional filter-drier included but not installed. Comes precharged for 15-foot line set and AHRI matched coil.
Contact:Century, Jackson, Mich.; attn: Robert Sycks, Director of Sales, CAC; 517-787-2100; 517-787-9341 (fax); info@heatcontroller.com; www.century-hvac.com.
eProduct 178
ClimateMaster
Model:Tranquility water-to-water (TMW) Series heat pumpFootprint (inches):Manufacturer did not specify.
Serviceability features:Multiple removable panels for service access.
Technical support:Available at 405-745-6000
Technical support materials:All technical support materials are available online.
Noise-reduction features:Dual-isolated compressor mounting system and heavy-gauge steel cabinet help make the series one of the quietest water-to-water units on the market. Compressors are mounted on vibration-isolation grommets to a heavy-gauge mounting plate, which is then isolated from the cabinet base with rubber grommets for further vibration/sound attenuation.
IAQ equipment supported:Manufacturer did not specify.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:The series offers high efficiency with advanced features, extremely quiet operation, and application flexibility at competitive prices. The series can be used for radiant floor heating, snow/ice melt, chilled water for fan coils, potable hot water generation, hot/chilled water for makeup air, and many other types of HVAC applications.
Warranty information:Standard and extended warranties available. Contact company for more details at 405-745-6000.
Special installation requirements:Manufacturer did not specify.
Contact:ClimateMaster Inc., Oklahoma City; attn: Evie Sibert, 405-745-6000; 405-745-4102 (fax); esibert@climatemaster.com; www.climatemaster.com.
eProduct 179
Coaire
Model:COTH-36M3Z heat pumpFootprint (inches):29 (length) by 29 (width) by 25 (height)
Serviceability features:Easier-to-access control panel features a defrost PCB, complete with sealed contactor service valves positioned for simpler installation of the refrigerant lines.
Technical support:Available at 877-262-4731, 8 a.m.-5 p.m. Eastern.
Technical support materials:Installation manuals, service manual.
Noise-reduction features:Fan design reduces unit noise levels.
IAQ equipment supported:Manufacturer did not specify.
Thermostat compatibility:Compatible with most thermostats.Replacement parts compatibility:Some shared parts, some unique.
Additional features:Reduced noise levels, reduced footprint and height.
Warranty information:Ten-years compressor, 10-year parts.
Special installation requirements:Easier to install, space saving.
Contact:Coaire, Santa Fe Springs, Calif.; attn: John Miles, 562-587-7837; 562-699-4612 (fax); johnm@coaire.com; www.coaire.com.
eProduct 180
Coleman
Model:Echelon™ package product, DYZ, DYQFootprint (inches):49 (length) by 47 (width) by 33 (height)
Serviceability features:Slide-out blower assembly, external refrigerant pressure ports, high- and low-pressure safeties, control board with diagnostic indicator.
Technical support:The first level of support is provided by the distributor. Factory support available to distributors and dealers by calling 877-874-7378, 7 a.m.-6 p.m. Central.
Technical support materials:Technical data, installation manual, wiring diagrams, and other support documentation at www.upgnet.com.
Noise-reduction features:The WhisperDrive™ swept-wing fan system, along with an insulated cabinet and base pan, provide very low noise and vibration transmission.
IAQ equipment supported:One-inch fiberglass filters are standard on the three-phase product and optional on single-phase product. An optional factory- or field-installed filter rack accommodates both 1- and 2-inch filters.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Some shared parts, some unique.
Additional features:Both the new product and the 14-SEER/12-EER DPQ product include MicroChannel condenser coil. This new technology is durable and corrosion resistant. It also requires less coil area and half the refrigerant charge required for standard copper tube, aluminum fin coil-equipped units.
Warranty information:The single-phase product carries a 10-year parts, 10-year compressor, and 20-year heat exchanger. The three-phase product carries one-year parts, five-years compressor and 10-year heat exchanger. Extended warranties are available on parts, compressors, and labor.
Special installation requirements:Duct configurations can be changed from sideflow (horizontal) to downflow (vertical) by moving prepainted, insulated panels from one position to another. All units accept gas, electric, and control service from the bottom or side of the unit.
Contact:Johnson Controls, Norman, Okla.; attn: Brian Wathen, 405-419-6557; 405-419-6593 (fax); brian.n.wathen@jci.com; www.colemanhvacdealer.com.
eProduct 181
Footprint (inches):30 (length) by 18, 21 or 25 (width) by 33 (height)
Serviceability features:The unit’s 33-inch height fits in tight spaces. Quarter-turn knobs provide easier door removal, and a solid, removable bottom panel makes conversion easier. Units feature easier access to controls to connect power/control wiring, fully supported blower assembly for easier access and blower removal, and high-level self diagnostics with fault code display.
Technical support:First level of support is provided by the distributor. Factory support is available to distributors and dealers by calling 877-874-7378, 7 a.m.-5 p.m. Central.
Technical support materials:Technical guide, submittal data sheet, guide specs, installation instructions, user’s manual, and parts list are available at www.upgnet.com or by request.Noise-reduction features:The unit features quiet inducer operation; an insulated blower compartment ensures quieter operation of the blower.
IAQ equipment supported:External air filters offer flexibility in meeting customer IAQ needs. The unit is compatible with all Coleman premium IAQ products.
Thermostat compatibility:Compatible with most thermostats. A wide selection is available to provide optimum performance and features for any installation. An adjustable delay timer allows two-stage operation with a single-stage thermostat.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:The entire product family qualifies for the federal tax credit program. It also employs induced combustion, reliable hot surface ignition, high-heat-transfer aluminized tubular heat exchangers, and a patent-pending, self-priming internal condensate trap design. Two-stage operation includes a two-stage gas valve and two-stage inducer.
Warranty information:The furnace includes a lifetime warranty on the heat exchanger, 10-year heat exchanger in commercial applications, and five-years limited parts; extended 10-year limited parts applies when the furnace is registered online within 90 days of purchase for replacement or closing for new home construction.
Special installation requirements:None. The smaller cabinet, convertible design, and no knockouts make this unit easier to install in replacement or new construction applications.
Contact:Johnson Controls, Norman, Okla.; attn: Brian Michael, Coleman Brand Manager, 405-419-6230; 405-419-6545 (fax); brian.k.michael@jci.com; www.colemanhvacdealer.com.
eProduct 182
Comfort-Aire
Model:GeoMax2 HTS Series geothermal heat pumpFootprint (inches):26-31 (length) by 22-25 (width) by 19-21 (height)
Serviceability features:Panels on three sides are removed for access to components. Back-seating service valves with service ports are included.
Technical support:Available at 517-787-2100, 8 a.m.-5 p.m. Eastern, weekdays.
Technical support materials:Installation-operation-maintenance manual, along with separate parts list, available as PDFs by e-mail or sent as hard copies; technical documentation also available online for authorized distributors.
Noise-reduction features:Noise-reduction features include double-isolation-mounted compressors, compressor springs, insulated compressor compartment, and interior cabinet insulation using ½-inch coated glass material.
IAQ equipment supported:Unit runs continuously to maintain constant temperature and humidity level, and air flows through the filter whenever it is running.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Some shared parts, some unique.
Additional features:Instantly shifts from part- to full-load capacity for optimal comfort and exceptional efficiency. Multistage scroll compressor. Hot water generator with built-in pump and CuNi coil standard. Solid-state controls with performance monitoring system allow maintenance scheduling. 20° to 120°F extended operating range.
Warranty information:Twelve-years limited compressor, six-year limited parts (some limitations apply - see warranty on Website for details). AssurancePlus extended service agreements available.
Special installation requirements:Use with variable-speed air handler for variable-speed capability; coupled with air handler or add-on furnace coil, offers flexibility of dual fuel system. Ideal for compact spaces, can be stacked for multiunit installations.
Contact:Comfort-Aire, Jackson, Mich.; attn: Robert Sycks, 517-787-2100; 517-787-9341 (fax); info@heatcontroller.com; www.heatcontroller.com.
eProduct 183
Footprint (inches):29 (length) by 18-21 (width) by 34 (height)
Serviceability features:Furnace filter and components are accessed by removing thumb screws to remove the front panels. Controls are integrated into a single board that also includes on-board diagnostics.
Technical support:Available at 517-787-2100, 8 a.m.-5 p.m. Eastern, weekdays.
Technical support materials:Installation-operation manual, user’s guide, service manual, and parts list can be e-mailed as PDFs or sent as hard copies; also available online to authorized distributors.
Noise-reduction features:Insulated blower compartment, specially designed inducer system, and slow-opening gas valve.
IAQ equipment supported:Because the unit operates continuously (generally in the low stage) to maintain a consistent temperature, air continuously passes through the filter.Thermostat compatibility:Requires a special thermostat. Two-stage thermostat is recommended.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:Two heat exchangers extract maximum heat from the burner for efficiency. In-shot burners are engineered to provide most efficient air/gas mixture. Multiple safety features include 100-percent safety lock-out, redundant main gas control, and blower compartment safety switch. Permanent washable filter. Automatically shifts from low to high stage when extra heat is needed.
Warranty information:Limited lifetime warranty on primary and secondary heat exchangers; 12-year limited on other parts (see warranty on Website for details and limitations). AssurancePlus extended service agreements available.
Special installation requirements:Furnace comes completely assembled and prewired. Connections for gas, electricity, and condensate drain can be made on the left or right side. Combustion air can be piped to either the top or side of the cabinet (special molded fitting is provided).
Contact:Comfort-Aire, Jackson, Mich.; attn: Robert Sycks, 517-787-2100; 517-787-9341 (fax); info@heatcontroller.com; www.heatcontroller.com.
eProduct 184
Comfortmaker
Model:PGD4 package gas/electric unitFootprint (inches):33-44 (length) by 48 (width) by 40-54 (height)
Serviceability features:Three separate service panels, clearly marked with embossed symbols, offer access to the compressor, blower compartment and control box. Service techs can keep the unit on while running diagnostics, since they can have one panel open with others closed.
Technical support:Factory-trained Technical Service Advisors (TSAs) on staff at local distributors provide technical assistance, troubleshooting at the local level.
Technical support materials:Product information posted online at dealer Website includes product spec sheets, installation-operation manuals, and technical support/parts manuals. Technical support materials are also available from local distributors.
Noise-reduction features:Newly designed, formed top panel provides additional stability for quieter operation.IAQ equipment supported:Dehumidification cooling speed standard on control board. Internal filter kits available as accessories.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:Eligible for the 2009-2010 U.S. HVAC tax credit for efficient fans. Compact units fit in bed of standard pick-up truck. Full-perimeter steel base rails give units extra stability and make them easier to load and transport. X-13 indoor blower motor delivers efficient airflow. Hail guard standard on all models.
Warranty information:15-year limited heat exchangers; 10-year parts limited with timely registration (restrictions apply; see warranty certificate for details). To learn more about all of these limited warranties, go to www.gocomfortmaker.com and click on the “Warranty” tab on the menu.
Special installation requirements:Metal base rails for simplified rigging (roof installations).
Contact:International Comfort Products (ICP), LLC, Nashville, Tenn.; attn: John Mott, 800-315-4370; 615-383-2215 (fax); john.mott@mottpr.com; www.gocomfortmaker.com.
eProduct 185
Footprint (inches):29 (length) by 19-25 (width) by 40 (height)
Serviceability features:Furnace includes a built-in electronic diagnostic system that can be used even while the furnace is running. These low-profile furnaces are designed with easier-to-remove doors and extra-spacious service compartments to give techs room to work. Most hose and clamp connections are premade by the factory, substantially reducing installation time.
Technical support:Factory-trained Technical Service Advisors (TSAs) on staff at local distributors provide technical assistance, troubleshooting at the local level.
Technical support materials:Product information posted online at dealer Website includes product spec sheets, installation-operation manuals, and technical support/parts manuals. Technical support materials are also available from local distributors.
Noise-reduction features:The unit has two-stage heating, which means it operates in the quieter first stage 70-80 percent of the time. The one-piece steel cabinet is thermal-lined and an insulated blower compartment provides added sound protection. Solid doors provide a sealed combustion compartment for quieter operation.
IAQ equipment supported:Predrilled accessory holes and convenient wiring hook-ups make it easier to add humidifiers, electronic air cleaners, and other accessories.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:Eligible for the 2009-2010 U.S. HVAC tax credit. Four-position furnace provides maximum efficiency, quiet operation, and premium comfort of variable-speed, two-stage heating. Meets California low-NOx emissions standards. Variable-speed blower motor cuts electricity costs. Furnace is equipped with long-lasting silicon nitride igniters. One- or two-pipe venting. Easier-view troubleshooting LED fault indicator diagnoses system-related malfunctions.
Warranty information:Ten-years No Hassle Replacement™ limited warranty; lifetime limited heat exchangers; 10-year parts limited timely registration (restrictions apply; see warranty certificate for details). To learn more about all of these limited warranties, go to www.GoComfortmaker.com and click on the “Warranty” tab on the menu.
Special installation requirements:Shipped as natural gas in upflow configuration, with all parts included for downflow, horizontal-left and right with no need for accessory conversion kits. LP gas kits available.
Contact:International Comfort Products (ICP), LLC, Nashville, Tenn.; attn: John Mott, 800-315-4370; 615-383-2215 (fax); john.mott@mottpr.com; www.GoComfortmaker.com.
eProduct 186
Concord
Model:CG95 furnaceFootprint (inches):28 (length) by 18 and 21 (width) by 44 (height)
Serviceability features:Tool-less service doors for quick service access. Slide out blower design for easier removal - 5 fault code memory for troubleshooting accuracy
Technical support:Available at 800-515-3501, 8 a.m.-5 p.m. Eastern.
Technical support materials:All technical data available online.
Noise-reduction features:Manufacturer did not specify.
IAQ equipment supported:Manufacturer did not specify.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:This series of 95-percent-AFUE, single-stage, PSC furnaces qualify for the federal tax credits. Consumers should consult with a tax professional to determine their eligibility for the tax credit.
Warranty information:Ten-years parts and limited lifetime heat exchanger with online registration within 60 days of installation.
Special installation requirements:None.Contact:Concord, West Columbia, S.C.; attn: Sloan Black, 803-738-4114; 972-808-8404 (fax); sloan.black@alliedair.com; www.concord-air.com.
eProduct 187
Daikin
Model:Altherma air-to-water heat pumpFootprint (inches):12 (length) by 35 (width) by 53 (height)
Serviceability features:Advanced self-diagnostic auto check function will detect a malfunction and immediately display alarm or code on the remote controller so it can be resolved quickly and effectively. In the event of a power interruption of up to two hours, the system automatically resumes with the set parameters (automatic restart after power interruption).
Technical support:Available at 972-245-1510, Monday-Friday, 8:30 a.m.-5 p.m.
Technical support materials:Service manual, engineering data book, installation manual, submittal data sheets, parts lists.
Noise-reduction features:The outdoor unit makes hardly any noise. The contractor can set the outdoor unit to produce 10 dBA less noise during the night.
IAQ equipment supported:Manufacturer did not specify.
Thermostat compatibility:Requires a special thermostat.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:Altherma is a heating, cooling, and domestic hot water supply based on heat pump technology that is three to five times more energy efficient than a conventional fossil fuel boiler. It extracts latent heat energy present in the ground, air, or water, and can heat a home even when temperatures fall as low as -4°F. The air-to-water heat pump can provide full heating capacity on its own as well as connect to (existing) fossil fuel boilers and solar energy sources for warm water production. The system reduces the impact of heating systems on the climate by reducing substantially CO2 emissions.
Warranty information:Standard limited warranty includes seven-year compressor, five-years parts, one-year limited labor.
Special installation requirements:R-410A certification; factory training; standard installation instructions; service space and piping limitations must be followed as described in the engineering data book. Unit is available in both split system or monobloc, where all hydraulic parts are located within the outdoor unit.
Contact:Daikin, Carrollton, Texas; attn: Marc Bellanger, 972-245-1510; 972-245-1038 (fax); marc.bellanger@daikinac.com; www.daikinac.com.
eProduct 188
Footprint (inches):11 (length) by 31 (width) by 22 (height)
Serviceability features:Built-in self diagnostics, suitcase-style condensing unit cabinet, horizontal discharge air, compact and lightweight, serviceable-washable filter.
Technical support:Available at 972-245-1510 Monday-Friday, 8:30 a.m.-5 p.m.
Technical support materials:Service manual, engineering data book, installation manual, submittal data sheets, parts lists.
Noise-reduction features:Indoor unit quiet operation can be set to a 46 percent lower sound (decibel) level compared to high fan speed (down to 23 dBA). Outdoor unit inverter compressor sound attenuation blanket, fan design, and new twist grill allow for a low sound level of 46 dBA.
IAQ equipment supported:Prefiltered air enters the Flash Streamer, which discharges high-energy electrons that analyze, decompose, and remove molecules of allergens, odors, unwanted bacteria, and other hazardous chemical material by colliding with high-speed electrons 1,000 times faster than plasma filters. Tests results show that in 120 minutes, Flash Streamer eliminated 95.2 percent of a simulated virus.
Thermostat compatibility:Requires a special thermostat.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:The inverter compressor boosts performance in low temperatures and the system will heat in ambient conditions down to -4°F. Its heating capability exceeds the standard split-system capacity by up to 164 percent. The system provides all-in-one comfort in a single appliance, which cleans the air and can be programmed to a relative humidity setting. All models qualify for energy efficiency tax credits available in 2009 and 2010.
Warranty information:Standard limited warranty includes seven-year compressor, five-years parts, one-year limited labor.
Special installation requirements:R-410A certification; factory training; standard installation instructions; service space and piping limitations must be followed as described in the engineering data book.
Contact:Daikin, Carrollton, Texas; attn: Marc Bellanger, 972-245-1510; 972-245-1038 (fax); marc.bellanger@daikinac.com; www.daikinac.com.
eProduct 189
Day and Night
Model:Constant Comfort™ VS 95 gas furnaceFootprint (inches):29 (length) by 19-25 (width) by 40 (height)
Serviceability features:Easier-to-remove doors and spacious service compartments give techs room to work. Low-profile furnace includes a built-in electronic diagnostic system that can be used while the furnace is running. Most hose and clamp connections are premade by the factory, reducing installation time.
Technical support:Factory-trained Technical Service Advisors (TSAs) on staff at local distributors provide technical assistance, troubleshooting at the local level.
Technical support materials:Product information posted online at dealer Website includes product spec sheets, installation-operation manuals, and technical support/parts manuals. Technical support materials are also available from local distributors.
Noise-reduction features:Solid doors provide a sealed combustion compartment for quiet operation. The one-piece steel cabinet is thermal-lined and an insulated blower compartment provides added sound protection. The unit has two-stage heating which means it operates in the quieter first stage 70-80 percent of the time.
IAQ equipment supported:Predrilled accessory holes and convenient wiring hook-ups make it easier to add humidifiers, electronic air cleaners and other accessories.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:Eligible for the 2009-2010 U.S. HVAC tax credit. Meets California low-NOx emissions standards. Four-position furnace provides maximum efficiency, quiet operation and premium comfort of variable-speed, two-stage heating. Variable-speed blower motor cuts electricity costs. One- or two-pipe venting. Easier-to-view troubleshooting LED fault indicator. Long-lasting silicon nitride igniters.
Warranty information:Ten-years No Hassle Replacement™ limited warranty; lifetime limited heat exchangers; 10-year parts limited with timely registration (restrictions apply; see warranty certificate for details). To learn more about all of these limited warranties, go to www.GoDayandNight.com and click on the “Warranty” tab on the menu.
Special installation requirements:Shipped as natural gas in upflow configuration, with all parts included for downflow, horizontal-left and right with no need for accessory conversion kits. LP gas kits available.
Contact:International Comfort Products (ICP), LLC, Nashville, Tenn.; attn: John Mott, 800-315-4370; 615-383-2215 (fax); john.mott@mottpr.com; www.godayandnight.com.
eProduct 190
Footprint (inches):33-44 (length) by 48 (width) by 40-54 (height)
Serviceability features:Three separate service panels, clearly marked with embossed symbols, offer easier access to the compressor, blower compartment and control box. Service techs can keep the unit on while running diagnostics, since they can have one panel open with others closed.
Technical support:Factory-trained Technical Service Advisors (TSAs) on staff at local distributors provide technical assistance, troubleshooting at the local level.
Technical support materials:Product information posted online includes product spec sheets, installation-operation manuals, and technical support/parts manuals. Technical support materials are also available from local distributors.
Noise-reduction features:Newly designed, formed top panel provides additional stability for quieter operation.
IAQ equipment supported:Dehumidification cooling speed standard on control board. Internal filter kits available as accessories.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:Eligible for the 2009-2010 U.S. HVAC tax credit for efficient fans. Compact units fit in bed of standard pick-up truck. X-13 indoor blower motor delivers efficient airflow. Full-perimeter steel base rails give extra stability for loading and transporting. Stainless steel heat exchanger. Hail guard standard on all models.
Warranty information:Seven-year No Hassle Replacement™ limited warranty; lifetime limited heat exchangers; 10-year parts limited including compressor with timely registration (restrictions apply; see warranty certificate for details). To learn more about all of these limited warranties, go to www.GoDayandNight.com and click on the “Warranty” tab on the menu.
Special installation requirements:Metal base rails for simplified rigging (roof installations).
Contact:International Comfort Products (ICP), LLC, Nashville, Tenn.; attn: John Mott, 800-315-4370; 615-383-2215 (fax); john.mott@mottpr.com; www.godayandnight.com.
eProduct 191
Ducane
Model:CG95 furnaceFootprint (inches):28 (length) by 18 and 21 (width) by 44 (height)
Serviceability features:Tool-less service doors for quick service access. Slide-out blower design for easier removal. Five fault code memory for troubleshooting accuracy
Technical support:Available at 800-515-3501, 8 a.m.-5 p.m. Eastern.
Technical support materials:All technical data available online.
Noise-reduction features:Manufacturer did not specify.IAQ equipment supported:Manufacturer did not specify.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:This series of 95-percent AFUE, single-stage, PSC furnaces qualify for the federal tax credits. Consumers should consult with a tax professional to determine their eligibility for the tax credit.
Warranty information:Ten-years parts and limited lifetime heat exchanger with online registration within 60 days of installation.
Special installation requirements:None.
Contact:Allied Air, West Columbia, S.C.; attn: Sloan Black, 803-738-4114; 972-808-8404 (fax); sloan.black@alliedair.com; www.alliedair.com.
eProduct 192
EarthLinked
Model:SC and SW ground-source heat pumpFootprint (inches):28 (length) by 24 (width) by 25 (height)
Serviceability features:Unit features Adaptiv™ refrigerant flow controls, which make system charging simple. Service valves provided to isolate earth loops from compressor unit. SW model includes on demand domestic water preheating.
Technical support:Available, 8 a.m.-5 p.m. Eastern. Authorized dealers have access to after-hours phone support.
Technical support materials:Technical manuals, wiring diagrams, service/troubleshooting info, installation data, parts and part numbers immediately available to authorized installers via company website.
Noise-reduction features:Acoustically insulated cabinet for quiet operation. No outdoor fan noise.
IAQ equipment supported:Higher latent capacity means better dehumidification.
Thermostat compatibility:Preferred thermostat features rate-of-recovery algorithm to initiate auxiliary heat.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:This geothermal heat pump uses highly conductive copper loops buried in direct contact with the earth. The direct-exchange method eliminates the requirement for the antifreeze and additional circulating pumps found in water-source geothermal systems.
Warranty information:Two-year all parts and labor, five-years parts and labor on all major refrigerant circuit components, extended warranty (10 years) available.
Special installation requirements:The product is sold only to factory-trained installers. Training event information can be found at www.earthlinked.com./dealer-info/seminars.
Contact:EarthLinked Technologies, Inc., Lakeland, Fla.; attn: Joe Parsons, 863-701-0096; 863-701-7796 (fax); jparsons@earthlinked.com; www.earthlinked.com.
eProduct 193
Fraser-Johnston/Evcon
Model:DYZ, DYQ packaged productFootprint (inches):49 (length) by 47 (width) by 33 (height)
Serviceability features:Slide-out blower assembly, external refrigerant pressure ports, high- and low-pressure safeties, control board with diagnostic indicator.
Technical support:The first level of support is provided by the distributor. Factory support is available to distributors and dealers by calling 877-874-7378, 7 a.m.-6 p.m. Central.
Technical support materials:Technical data, installation manual, wiring diagrams, and other support documentation can be found online.
Noise-reduction features:The low sound, SilentDrive™ swept-wing fan system, along with an insulated cabinet and base pan, provide a product with very low noise and vibration transmission.
IAQ equipment supported:One-inch fiberglass filters are standard on the three-phase product and optional on the single-phase product. An optional factory- or field-installed filter rack will accommodate both 1- and 2-inch filters.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Some shared parts, some unique.
Additional features:Both the new product and the 14 SEER/12 EER include the new MicroChannel condenser coil. This new technology is durable and corrosion resistant. It also requires much less coil area and half the refrigerant charge required for standard copper tube, aluminum fin coil-equipped units.
Warranty information:The single-phase product carries 10-year parts, 10-year compressor and 20-year heat exchanger warranty. The three-phase product carries one-year parts, five-years compressor, and 10-year heat exchanger. Extended warranties are available on parts, compressors, and labor.
Special installation requirements:Duct configurations can be changed from sideflow (horizontal) to downflow (vertical) by moving prepainted, insulated panels from one position to another. All units accept gas, electric, and control service from the bottom or side of the unit.
Contact:Johnson Controls, Norman, Okla.; attn: Brian Wathen, 405-419-6557; 405-419-6593 (fax); brian.n.wathen@jci.com.
eProduct 194
Friedrich Air Conditioning Ductless Split System
Model:M12YG ductless heat pumpFootprint (inches):8 (length) by 31 (width) by 10 (height)
Serviceability features:Easier access lift-out, cleanable air filter. Removable front panel. Factory-installed access ports.
Technical support:Available 8 a.m.-4:30 p.m. Central at 877-599-5665. Installation-operation manuals available on Website.
Technical support materials:Operating manual, installation manual, submittal sheet, warranty information, service parts manual, and sales data.
Noise-reduction features:Internal tubing is insulated and the compressor is blanketed to provide acoustic dampening for the outdoor condensing unit. Indoor air handler features an ultraquiet tangential blower wheel for air distribution.
IAQ equipment supported:Washable, reusable filters. Variable-speed motors and variable-capacity compressor for improved air circulation and dehumidification. Continuous air sweep mode.
Thermostat compatibility:Factory-supplied programmable remote control.
Replacement parts compatibility:Some shared parts, some unique.
Additional features:Commercial-grade features include corrosion-resistant components, powder-coated galvanized steel cabinet, and insulated wiring terminals. Both indoor and outdoor units feature specialized bent and angled coils to pack the most heat exchanger surface into a compact package for superior efficiencies. Both the indoor and outdoor units are controlled by intelligent microprocessors that determine optimum running characteristics and self diagnostics. Advanced inverter technology delivers greater energy efficiency and temperature precision with the added benefit of reducing energy costs. Ultra-high SEER rating and ozone-friendly R-410A are great environmental selling points.
Warranty information:One-year parts and five-years compressor.
Special installation requirements:Factory precharged for 25 feet. Max line length, 66 feet. Max height difference, 49 feet. Minimum ampacity, 15 amps. Cooling watts, 690. Insulated line sets available for all split systems in 15- and 35-foot lengths. Each line set is equipped with flare nuts on both ends. Both liquid and suction lines are insulated. Line sets can be joined with field-supplied double female connectors.
Contact:Friedrich Air Conditioning Co., San Antonio, Texas; attn: Bernadette Moody, 877-599-5665; hvac@friedrich.com; www.friedrich.com.
eProduct 195
Frigidaire
Model:FG7T iSEER furnaceFootprint (inches):Manufacturer did not specify.
Serviceability features:Color-coded wire harness is designed to fit the components, all with quick-connect fittings for service and replacement. Diagnostic lights for troubleshooting without counting flashes. A dedicated light for flame signal strength; two lights in combination indicate all other fault codes with easier-to-recognize states. Integrated control board includes connections for electronic air cleaner and humidifier. Two-piece door design uses captured screws to prevent losing door screws.
Technical support:Available at 800-422-4328, Monday-Friday, 8 a.m.-4:30 p.m. Central.
Technical support materials:Technical specs and installation guides available 24/7 on literature library online.
Noise-reduction features:Sealed blower compartment door to reduce air leakage and insulated for quiet operation.
IAQ equipment supported:Two-stage, variable-speed technology allows furnace to run longer at lower speeds for a more uniform, comfortable mix of air and better filtration.Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:Furnace has iSEER, an energy-efficient, brushless DC (ECM) motor that gives up to a 1-SEER-point efficiency gain in cooling. Its low height makes it easier to install in low-ceiling applications, works well with taller high-SEER coils, is easier to handle and install.
Warranty information:With product registration, 10-year parts and 10-year Quality Pledge to replace the entire unit if the heat exchanger fails.
Special installation requirements:None.
Contact:Nordyne, O’Fallon, Mo.; attn: Matt Lattanzi, 800-422-4328; 636-561-7399 (fax); res_sales@nordyne.com; www.frigidaire.net.
eProduct 196
Footprint (inches):31 (length) by 31 (width) by 33 (height)
Serviceability features:Easier compressor and control access designed to make servicing easier for the contractor. Access panels are provided to all controls and the compressor from the side of the unit; iQ Drive thermostat provides system diagnostics.
Technical support:Available at 800-422-4328, Monday-Friday, 8 a.m.-4:30 p.m. Central.
Technical support materials:Technical specs and installation guides available 24/7 online.
Noise-reduction features:Compressor sound blanket, swept-wing fan blade, one-piece top/orifice. Modulating compressor also reduces noise. Unit can operate as low as 59 dB.
IAQ equipment supported:In addition to the low sound levels and even temperatures, the iQ Drive also delivers whole-home comfort through its built-in dehumidification features. The homeowner can set a desired humidity level based on their needs - from 35-70 percent.
Thermostat compatibility:Requires a special thermostat.
Replacement parts compatibility:Some shared parts, some unique.
Additional features:Highest efficiency with the lowest sound levels in an air-source heat pump. Up to 22 SEER with sound ratings of 59-72 dB depending upon operating conditions. Inverter-driven rotary compressor provides fully variable operation, from 40-118 percent of capacity.
Warranty information:With product registration, 10-year parts and 10-year Quality Pledge to replace the entire unit if the compressor fails. All split-system products must be installed with a matched indoor air handler or indoor coil to qualify.
Special installation requirements:Contractors must be iQ Drive certified before they can purchase this heat pump system.
Contact:Nordyne, O’Fallon, Mo.; attn: Matt Lattanzi, 800-422-4328; 636-561-7399 (fax); res_sales@nordyne.com; www.frigidaire.net.
eProduct 197
Fujitsu
Model:Halcyon compact cassette AUU9RML mini-split heat pumpFootprint (inches):22 (length) by 22 (width) by 10 (height)
Serviceability features:All major components can be accessed from the panel on the grille below the unit, rather than going above the unit into the ceiling.
Technical support:Available at 866-952-8324, 8 a.m.-8 p.m. Eastern or by e-mail (servicehvac@fujitsugeneral.com).
Technical support materials:Operation manual, installation manual, service manual, detailed specs, interactive troubleshooting guides, blow-apart parts diagrams, online training materials are available on Website via login/password.
Noise-reduction features:Indoor unit operates at very quiet sound levels.
IAQ equipment supported:Manufacturer did not specify.
Thermostat compatibility:Unit comes with a programmable remote.
Replacement parts compatibility:Does not share replacement parts with other models.
Additional features:The compact cassette is part of the multizone line, allowing up to four indoor units to be connected to one outdoor unit. The compact size of this model allows it to fit into a standard ceiling tile without modification.
Warranty information:Two-year parts, six-year compressor.
Special installation requirements:Manufacturer did not specify.
Contact:Fujitsu General America, Inc., Fairfield, N.J.; attn: Erin Mezle, 973-575-0380; 973-836-0429 (fax); hvac@fujitsugeneral.com; www.fujitsugeneral.com.
eProduct 198
Footprint (inches):9 (length) by 31 (width) by 11 (height)
Serviceability features:Manufacturer did not specify.
Technical support:Available at 866-952-8324, 8 a.m.-8 p.m. Eastern or by e-mail (servicehvac@fujitsugeneral.com).
Technical support materials:Operation manual, installation manual, service manual, detailed specs, interactive troubleshooting guides, blow-apart parts diagrams, online training materials are available on our Website via login/password.
Noise-reduction features:Indoor unit operates at sound levels ranging from 24-46 dBA (from Quiet Mode to Hi Mode).
IAQ equipment supported:Contains Apple Catechin filter, which deodorizes by powerfully decomposing absorbed odors using the oxidizing and reducing effects of ions generated by the ultra-fine particle ceramic. Also contains an ion deodorizing filter, which absorbs fine dust, mold spores, and harmful microorganisms by static electricity.
Thermostat compatibility:Unit comes with a programmable remote.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:System 9RLS has a SEER rating of 26. This system qualifies for a federal tax credit of up to $1,500.
Warranty information:Two-year parts, six-year compressor.
Special installation requirements:None.
Contact:Fujitsu General America, Inc., Fairfield, N.J.; attn: Erin Mezle, 973-575-0380; 973-836-0429 (fax); hvac@fujitsugeneral.com; www.fujitsugeneral.com.
eProduct 199
GeoComfort
Model:GT Series geothermal package combination unitFootprint (inches):26-31 (length) by 22-28 (width) by 50-60 (height)
Serviceability features:Eight access panels, removable low-voltage terminal strips, LED fault lights, flow switch protected, Schrader-mounted pressure switches, stab-in plenum heater, double O-ring source-side water connections.Technical support:Design and application support available; 24-hour technical support.
Technical support materials:Full spec catalogs, installation manuals, wiring diagrams, brochures.
Noise-reduction features:Eco-friendly, recycled, foil-backed denim insulation, grommet-mounted compressors.
IAQ equipment supported:E-coated air coils, ECM blowers, dehumidification control, pleated filters, stainless steel drain pans, foil-backed denim insulation (not fiberglass).
Thermostat compatibility:Requires Aquastat for hydronic heating.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:Four LEDs indicate operating mode, input status, and microprocessor operation. DIP switches provide field-selectable options such as priority mode (hot water, forced air, or shared priority) and fan operation. Five lockout LEDs provide fault status, and another LED flashes one time per 100 CFM to indicate airflow.
Warranty information:Ten-years refrigerant circuit, five-years all parts, three-years labor (dealer warrants first year). Optional 10/10/10-year warranty available.
Special installation requirements:Unit features hydronic heating as well as forced-air heating and cooling.
Contact:Enertech Manufacturing, LLC, Greenville, Ill.; attn: Dave Salyer, 618-664-9010; 618-664-4597 (fax); dsalyer@enertechmfg.com; www.geocomfort.com.
eProduct 200
Goodman
Model:DSZ18 heat pumpFootprint (inches):36 (length) by 36 (width) by 38 (height)
Serviceability features:Sweat connection service valves with easier access to gauge ports, top and side maintenance access, single-panel access to controls with space provided for field-installed accessories, factory-installed biflow liquid-line filter-drier.
Technical support:Available from local distributors, factory field representatives, and by calling 888-593-9988.
Technical support materials:Wiring diagrams, service/troubleshooting information, installation data, parts and part numbers are available to all installing contractors via the local distributor or they can be downloaded online from Partner Link at Website.
Noise-reduction features:High-density foam compressor cover, efficient condenser fan motor, sound-reducing louvered top.
IAQ equipment supported:Fully compatible with all IAQ enhancement components and systems.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:Uses R-410A and features energy efficiencies and operating sound levels that are among the best in the HVAC industry, two-stage scroll compressor, and exceptional warranty coverage.
Warranty information:Lifetime compressor limited warranty and all functional parts covered by 10-year parts limited. To receive the warranties, online registration is required within 60 days of installation. Online registration is not required in California or Quebec. Full warranty details available online.
Special installation requirements:Offers exceptional installation flexibility.
Contact:Goodman Manufacturing Co, L.P., Houston; attn: Rex Anderson, 713-263-5064; 713-586-8059 (fax); rex.anderson@goodmanmfg.com; www.goodmanmfg.com.
eProduct 201
Footprint (inches):28 (length) by 18 (width) by 40 (height)
Serviceability features:Control board has self diagnostics; easier-to-install top venting is standard; alternate flue/vent located on right side; left or right gas and electric connections.
Technical support:Available from local distributors, factory field representatives, and by calling 888-593-9988.
Technical support materials:Wiring diagrams, service/troubleshooting information, installation data, parts and part numbers are immediately available to all installing contractors via the local distributor, or they can be downloaded online from Partner Link at Website.
Noise-reduction features:Quiet two-speed inducer motor, fully insulated heavy-gauge steel cabinet, quiet variable-speed circulator motor.
IAQ equipment supported:The auto-comfort mode offers enhanced dehumidification and energy savings during cooling operation. Unit has color-coded low-voltage terminals and provisions for electronic air cleaner and 120- or 24-V humidifiers.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Some shared parts, some unique.
Additional features:Features a patented aluminized-steel tubular heat exchanger and silicon nitride hot-surface ignition system. This furnace is run-tested several times during manufacturing assembly. The two-stage gas valve operates with two-stage or single-stage thermostats.
Warranty information:Ten-year unit replacement limited, lifetime heat exchanger limited, and 10-year parts limited. Online registration is required within 60 days of installation (not required in California or Quebec). Full warranty details available at Website.
Special installation requirements:Designed for multiposition installations (upflow, horizontal left or right).
Contact:Goodman Manufacturing Co, L.P., Houston; attn: Rex Anderson, 713-263-5064; 713-586-8059 (fax); rex.anderson@goodmanmfg.com; www.goodmanmfg.com.
eProduct 202
Hallowell International
Model:Acadia 024 heat pumpFootprint (inches):49 (length) by 31 (width) by 28 (height)
Serviceability features:The Acadia has industry-standard components. A multistage logic control board provides built-in diagnostics to prevent nuisance service calls. Accessible service panel. Foil-insulated cabinet enhances visibility.
Technical support:Support (24 hours) available at 207-990-5600.
Technical support materials:All materials, such as spec sheets, installation manual, performance charts, and technical paper are available at Website. Wiring diagrams, zone-control information, troubleshooting/service information, and repair parts are accessible through the Hallowell Technical Department or a distributor, depending on service area.
Noise-reduction features:Compressor department is insulated and isolated from the coil. Fully insulated line set. Discharge muffler on the primary compressor. Compressor mounting system helps eliminate vibration of the system and noise transmission through the line set.
IAQ equipment supported:UV, electronic, and media filtration products will be available in the future.
Thermostat compatibility:Requires a special thermostat (White Rodgers Blue 90 Series, three heat/two cool, multistage thermostat for heat pumps). Other thermostats are able to be used with prior approval from the Technical Department.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:The combined heating and cooling system utilizes patented Boosted Compression technology. This enables the system to efficiently absorb heat down to temperatures as low as -30°F. Homeowners are able to maintain a comfortable atmosphere without the need for fossil fuels.
Warranty information:Five-years parts and compressors from the manufacturer. Extended warranties available directly through the installers.
Special installation requirements:Insulate the entire line set from the outdoor unit to the AHU. Elevate the outdoor unit at least 6-8 inches on snow stands (or more, depending on the climate). Ten conductor thermostat wire necessary for the electrical components. Filter-drier is to be installed inside by the AHU and insulated.
Contact:Hallowell International, Bangor , Maine; attn: Nichole Cough, 207-990-5600; 207-990-5602 (fax); info@gotohallowell.com; www.gotohallowell.com.
eProduct 203
Footprint (inches):49 (length) by 31 (width) by 28 (height)
Serviceability features:The system has industry-standard components. A multistage logic control board provides built-in diagnostics to prevent nuisance service calls. Accessible service panel. Foil-insulated cabinet to enhance visibility.
Technical support:Support (24 hour) available at 207-990-5600.
Technical support materials:All support materials, such as the spec sheets, installation manual, performance charts, and technical paper are available at Website. Wiring diagrams, zone-control information, troubleshooting/service information, and repair parts are accessible through the Hallowell Technical Department or a distributor, depending on service area.
Noise-reduction features:The compressor department is insulated and isolated from the coil. Fully insulated line set. Discharge muffler on the primary compressor. Compressor mounting system helps eliminate vibration of the system and noise transmission through the line set.
IAQ equipment supported:UV, electronic, and media filtration products will be available in the future.
Thermostat compatibility:Requires a special thermostat (White Rodgers Blue 90 Series, three heat/two cool, multistage thermostat for heat pumps). Other thermostats are able to be used with prior approval from the technical department.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:The combined heating and cooling system utilizes patented Boosted Compression technology. This enables the system to efficiently absorb heat down to temperatures as low as -30°F. Homeowners are able to maintain a comfortable atmosphere without the need for fossil fuels.
Warranty information:Five-year parts and compressors from the manufacturer. Extended warranties available directly through the installers.
Special installation requirements:Insulate the entire line set from the outdoor unit to the AHU. Elevate the outdoor unit at least 6-8 inches on snow stands (or more, depending on the climate). Ten conductor thermostat wire necessary for the electrical components. Filter-drier is to be installed inside by the AHU and insulated.
Contact:Hallowell International, Bangor, Maine; attn: Nichole Cough, 207-990-5600; 207-990-5602 (fax); info@gotohallowell.com; www.gotohallowell.com.
eProduct 204
Heil
Model:PGS4 package gas/electric unitFootprint (inches):33-44 (length) by 48 (width) by 40-54 (height)
Serviceability features:Three separate service panels, clearly marked with embossed symbols, offer access to the compressor, blower compartment, and control box. Service techs can keep the unit on while running diagnostics, since they can have one panel open with others closed.
Technical support:Factory-trained Technical Service Advisors (TSAs) on staff at local distributors provide technical assistance, troubleshooting at the local level.
Technical support materials:Product information posted online at dealer Website includes spec sheets, installation-operation manuals, and technical support/parts manuals. Technical support materials are also available from local distributors.
Noise-reduction features:Quieter operation is a result of additional stability provided by newly designed, formed top panel.
IAQ equipment supported:Dehumidification cooling speed standard on control board. Internal filter kits available as accessories.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:Eligible for the 2009-2010 U.S. HVAC tax credit for efficient fans. Full-perimeter steel base rails give units extra stability for loading and transporting. X-13 indoor blower motor delivers efficient airflow. Stainless steel heat exchanger. Hail guard standard. Compact units fit in bed of standard pick-up truck.
Warranty information:Seven-year No Hassle Replacement™ limited warranty; lifetime limited heat exchangers; 10-year parts limited including compressor with timely registration (restrictions apply; see warranty certificate for details). To learn more about all of these limited warranties, go to www.GoHeil.com and click on the “Warranty” tab on the menu.
Special installation requirements:Metal base rails for simplified rigging (roof installations).
Contact:International Comfort Products (ICP), LLC, Nashville, Tenn.; attn: John Mott, 800-315-4370; 615-383-2215 (fax); john.mott@mottpr.com; www.GoHeil.com.
eProduct 205
Footprint (inches):29 (length) by 19-25 (width) by 40 (height)
Serviceability features:A troubleshooting LED fault indicator diagnoses system-related malfunctions, and it’s easier to view through a sight glass in the blower door. Conventional gas valves come standard for replacement and troubleshooting. Control board mounting plate is modified for access while servicing.
Technical support:Factory-trained Technical Service Advisors (TSAs) on staff at local distributors provide technical assistance, troubleshooting at the local level.
Technical support materials:Product information posted at dealer Website includes product spec sheets, installation-operation manuals, and technical support/parts manuals. Technical support materials are also available from local distributors.
Noise-reduction features:The one-piece steel cabinet is thermal lined for added sound protection. Solid doors provide a sealed combustion compartment for quieter operation.
IAQ equipment supported:Predrilled accessory holes and convenient wiring hook-ups make it easier to add humidifiers, electronic air cleaners, and other accessories.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:Furnace is equipped with silicon nitride igniters. All DLX 95 gas furnaces installed during 2009-10 qualify for the U.S. HVAC tax credit for 95-percent-AFUE gas furnaces when installed in upflow orientations. Some horizontal installations may not qualify. See IRS guidelines and sales representative for details.
Warranty information:Five-years No Hassle Replacement™ limited warranty; lifetime limited heat exchangers: Ten-years parts limited with timely registration (restrictions apply; see warranty certificate for details). To learn more about all of these limited warranties, go to www.GoHeil.com and click on the “Warranty” tab on the menu.
Special installation requirements:Shipped as natural gas in upflow configuration, with all parts included for downflow, horizontal-left and right with no need for accessory conversion kits. LP gas kits available.
Contact:International Comfort Products (ICP), LLC, Nashville, Tenn.; attn: John Mott, 800-315-4370; 615-383-2215 (fax); john.mott@mottpr.com; www.goheil.com.
eProduct 206
Hydron Module
Model:W-Series water-to-water unitFootprint (inches):32-48 (length) by 22-30 (width) by 20-24 (height)
Serviceability features:Four access panels, removable low-voltage terminal strips, LED fault lights, flow switch protected, Schrader-mounted pressure switches.
Technical support:Design and application support, plus 24-hour technical support.
Technical support materials:Full specification catalogs, installation manuals, wiring diagrams, brochures.
Noise-reduction features:Eco-friendly, recycled, foil-backed denim insulation, grommet-mounted compressors.
IAQ equipment supported:Manufacturer did not specify.Thermostat compatibility:Requires Aquastat thermostat.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:Features a stainless steel cabinet that’s bolted together instead of screwed together. All digital controls protect the unit against potential faults.
Warranty information:Ten-years refrigerant circuit, 10-years all parts, 10-years labor (dealer warrants first year), 10-years accessories.
Special installation requirements:The unit features a compact footprint and stackable cabinet.
Contact:Enertech Manufacturing, LLC, Greenville, Ill.; attn: Dave Salyer, 618-664-9010; 618-664-4597 (fax); dsalyer@enertechmfg.com; www.hydronmodule.com.
eProduct 207
Laars
Model:NeoTherm NTH boilerFootprint (inches):19-55 (length) by 25 (width) by 36-38 (height)
Serviceability features:Manufacturer did not specify.
Technical support:Applications engineering, technical support, and service support available Monday-Friday, 8 a.m.-5 p.m. Eastern at 800-900-9276.
Technical support materials:Spec sheets, submittal data sheets, installation/operation manual (includes parts identification and part numbers).
Noise-reduction features:Manufacturer did not specify.
IAQ equipment supported:Manufacturer did not specify.
Thermostat compatibility:All applicable sensors included.
Replacement parts compatibility:Some shared parts, some unique.
Additional features:Meets the standards of California’s AB-1953 and NSF/ANSI-61.
Warranty information:Twelve-years limited.
Special installation requirements:Zero clearance to combustibles tolerance, and the top connections (horizontal or vertical direct vent) make it suitable for tight installations.
Contact:Laars Heating Systems, Rochester, N.H.; attn: Bill Root, 603-336-6300; 603-335-3355 (fax); broot@laars.com; www.Laars.com.
eProduct 208
Lennox
Model:Dave Lennox Signature Collection G71MPP gas furnaceFootprint (inches):29 (length) by 18-25 (width) by 40 (height)
Serviceability features:Easier-access service panels and nonvolatile, direct-readout, alphanumeric diagnostics simplify service. Up to 10 diagnostic codes held in nonvolatile memory for retrieval at your convenience. Direct-readout diagnostics provide flame microamps with the push of a button. Low-voltage circuit breaker provides thermostat and control protection during service, installation, operation.
Technical support:Available 24/7 online at lennoxdavenet.net to registered contractors. Phone support available Monday-Friday, 8 a.m.-5 p.m. Central at 972-497-5799.
Technical support materials:All ancillaries are available in hard copy or online. Installation manuals, service manuals, consumer manuals, parts list. Regional technical and sales training available.
Noise-reduction features:Patented combustion air box, custom insulation, and variable-speed motors minimize sound. PreciseComfort™ technology minimizes heat output and airflow, maximizing efficiency and comfort.
IAQ equipment supported:Designed to work with and optimize all Lennox Healthy Climate™ IAQ accessories. AirFlex™ technology allows every aspect of airflow to be customized to optimize IAQ accessories such as Lennox nonozone-creating MERV-10 through -16 filtration and humidity control systems; 24- and 120-V control signals provided for accessory operation.
Thermostat compatibility:Compatible with most thermostats. A traditional two-stage thermostat provides full variable-capacity operation, 40-100 percent of rated capacity. The furnace can be defeatured to operate like a three-stage furnace by using a traditional one-stage thermostat.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:Every model is 95-percent AFUE in all installed positions. PreciseComfort™ technology constantly monitors space conditions and adjusts both heat and airflow in increments as small as 1 percent, or as large as necessary, to maximize comfort while minimizing operating costs. AirFlex technology allows airflow in every operating mode to be customized to meet each application’s needs.
Warranty information:Limited lifetime heat exchanger; 10-year limited all remaining covered components.
Special installation requirements:Four-way multiposition with no component rearrangement or field engineering required. Simply install and locate the trap in the appropriate position for the installed position. Direct, alphanumeric diagnostic readouts simplify set-up and installation, providing direct feedback to set-up selections. Vent links up to 150 feet provide installation flexibility. Self-calibrating inducer.
Contact:Lennox Industries, Richardson, Texas; attn: Ken Ely, 972-497-5000; 972-497-5254 (fax); ken.ely@lennoxind.com; www.lennox.com.
eProduct 209
LG Electronics
Model:Flex Multi-Split Quad Zone package water-source heat pumpFootprint (inches):13 (length) by 34 (width) by 32 (height)
Serviceability features:All control components are accessed on the right side of the chassis after removal of the top (lid) and front cover assembly. This unit is configured in much the same way as the smaller mini splits that may be more familiar to contractors in the field.
Technical support:Available Monday-Saturday, 7 a.m.-7 p.m. Central by calling 888-865-3026 and following the prompts.
Technical support materials:Contractors can register at: www.lgtechassist.com for access to e-manual downloads, service bulletins, and technical notes for a wide range of air conditioning equipment.
Noise-reduction features:Variable-speed fans slow, preventing whistling noise for reduced-load conditions.
IAQ equipment supported:Variable-speed compressor and fan matches load to cool longer, removing humidity from the air.
Thermostat compatibility:Requires a special thermostat.
Replacement parts compatibility:Does not share replacement parts with other models.
Additional features:Variable-speed multisplit matches load for dehumidification beyond conventional DX systems and promotes high energy efficiency. Unit allows individualized control and also allows the user to cool or heat only the rooms in use.
Warranty information:Parts only (two-year functional, six-year compressor).
Special installation requirements:Use standard refrigeration practices to install this equipment, being careful not to exceed published maximum pipe lengths.
Contact:LG Electronics, Chicago; attn: Katie Schaffer, 312-397-6025; 312-397-8841 (fax); katie.schaffer@lg-one.com; www.lghvac.com.
eProduct 210
Footprint (inches):13 (length) by 37 (width) by 54 (height)
Serviceability features:The outdoor unit chassis is front serviceable with access to control compartment on the upper-right front of the unit. Access is gained after removing cabinet screws and pulling the cover down and out. Since this chassis is side discharge, access to the twin inverter motors is gained by removing the plastic fan guard cover.
Technical support:Available Monday-Saturday, 7 a.m.- 7 p.m. Central by calling 888-865-3026 and following the prompts.
Technical support materials:Contractors can register at: www.lgtechassist.com for access to e-manual downloads, service bulletins, and technical notes for a wide range of equipment
Noise-reduction features:Night quiet mode for reduced noise levels.
IAQ equipment supported:Individualized zones prevent odors from being distributed to neighboring zones. Minimal or no ductwork removes areas for dust and mold to accumulate. Variable-speed compressors, fans, and variable refrigerant volume control matches load to cool longer, removing humidity from the air.
Thermostat compatibility:Requires a special thermostat.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:Variable-speed split system matches load for dehumidification beyond conventional DX systems. Reduces or removes ductwork and removes water piping from the system, removing losses and promoting high energy efficiency. The unit also allows users to run heating or cooling only in occupied spaces.
Warranty information:Parts only (two-year functional, six-year compressor).
Special installation requirements:Use of Y-branches and headers is mandatory for proper refrigerant flow. The use of LGMV (LG monitoring view) software is a must to verify proper EEV (expansion device) inverter fan, compressor, and bypass valve operation.
Contact:LG Electronics Commercial Air Conditioning, Chicago; attn: Katie Schaffer, 312-397-6025; 312-397-8841 (fax); katie.schaffer@lg-one.com; katie.schaffer@lg-one.com.
eProduct 211
Luxaire
Model:Acclimate™ package product DYZ, DYQFootprint (inches):49 (length) by 47 (width) by 33 (height)
Serviceability features:Slide-out blower assembly, external refrigerant pressure ports, high- and low-pressure safeties, control board with diagnostic indicator.
Technical support:The first level of support is provided by the distributor. Factory support is available to distributors and dealers by calling 877-874-7378 7 a.m.-6 p.m. Central.
Technical support materials:Technical data, installation manual, wiring diagrams, and other support documentation can be found at upgnet.com.
Noise-reduction features:The low-sound, SilentDrive™ swept-wing fan system, along with an insulated cabinet and base pan, provide low noise and vibration transmission.
IAQ equipment supported:One-inch fiberglass filters are standard on the three-phase product and optional on the single-phase product. An optional factory- or field-installed filter rack accommodates either 1- or 2-inch filters.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Some shared parts, some unique.
Additional features:Both the new product and the 14-SEER/ 12-EER DPQ products include MicroChannel condenser coil technology. This new technology is durable and corrosion resistant. It also requires less coil area and half the refrigerant charge required for standard copper tube, aluminum fin coil-equipped units.
Warranty information:The single-phase product carries a 10-year parts, 10-year compressor, 20-year heat exchanger warranty. The three-phase product carries a one-year parts, five-years compressor, and 10-year heat exchanger warranty. Extended warranties are available on parts, compressors, and labor.
Special installation requirements:Duct configurations can be changed from sideflow (horizontal) to downflow (vertical) by moving prepainted, insulated panels from one position to another. All units accept gas, electric, and control service from the bottom or side of the unit.
Contact:Johnson Controls, Norman, Okla.; attn: Brian Wathen, 405-419-6557; 405-419-6593 (fax); brian.n.wathen@jci.com; www.joinluxaire.com.
eProduct 212
Footprint (inches):30 (length) by 18, 21, or 25 (width) by 33 (height)
Serviceability features:The unit’s height allows it to fit in tight spaces. Quarter-turn knobs provide easier door removal, and solid removable bottom panels make conversion easier. Units feature easier access to controls to connect power/control wiring, fully supported blower assembly for easier access and blower removal, and high-level self diagnostics with fault code display.
Technical support:The first level of support is provided by the distributor. Factory support is available to distributors and dealers by calling 877-874-7378, 7 a.m.-5 p.m. Central.
Technical support materials:Technical guide, submittal data sheet, guide specs, installation instructions, user’s manual, and a parts list are available at www.upgnet.com or by request.
Noise-reduction features:The unit features quiet operation of the inducer, and an insulated blower compartment ensures quiet operation of the blower.
IAQ equipment supported:The unit features timed-on, adjustable-off blower capabilities for comfort. External air filters offer flexibility in meeting customer IAQ needs. Compatible with Luxaire premium IAQ products.
Thermostat compatibility:Compatible thermostat controls are available through accessory sourcing.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:The unit features a compact design for easier installation in tight spaces and a five-speed, direct-drive, high-efficiency DC motor. It also includes an induced-combustion, hot surface ignition; a high-heat-transfer aluminized tubular heat exchanger; and a patent-pending, self-priming internal condensate trap design for easier installation. All models qualify for the federal tax credit program.
Warranty information:Lifetime heat exchanger, 10-year heat exchanger in commercial applications, and five-years limited parts. Extended 10-year limited parts applies when the furnace is registered online within 90 days of purchase for replacement or closing for new home construction.Special installation requirements:None; the smaller cabinet, convertible design, and no knockouts make this unit easier to install in replacement or new construction applications.
Contact:Johnson Controls, Norman, Okla.; attn: Brian Michael, 405-419-6230; 405-419-6545 (fax); brian.k.michael@jci.com; www.joinluxaire.com.
eProduct 213
Marvair
Model:HVPSA, Classic Series package unitFootprint (inches):23 (length) by 45 (width) by 84 (height)
Serviceability features:High and low refrigerant access valves. LEDs identify operating status with flashing fault codes, accessible filter, compressor, and electrical control box.
Technical support:Available 24/7. During normal working hours, call 800-841-7854, ext. 146 or 113, in Cordele, Ga. (Eastern). For after-hours and weekend service, call the service pager at 800-204-8210.
Technical support materials:Wiring diagrams, installation and maintenance manual. Exploded views and parts lists can be downloaded from the Website. Service schools are periodically held at the factory and at customers’ premises.
Noise-reduction features:Low-vibration scroll compressor with sound jacket. Axial outdoor fan. Electronically commutated indoor air motor slowly ramps up its speed, eliminating abrupt sound at start-up. Very-low-torque ripple and the rotor construction effectively eliminate noise transmission through the motor’s shaft.
IAQ equipment supported:Two-stage compressor maintains more precise temperature and humidity control. Ventilation options include the GreenWheel® ERV to remove moisture before it is introduced into the building. Hot gas reheat is available for more precise humidity control.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:The two-stage compressor means lower energy costs and a more comfortable indoor environment. During mild days the first stage can satisfy the load, minimizing temperature and humidity fluctuations.
Warranty information:One-year parts, five-years compressor. Extended warranties are available. Contact company for details.
Special installation requirements:Packaged design, factory-charged unit does not require field charging. Sloped top eliminates need for rainhood. Factory-installed disconnect is standard on all 208/230-V units. Built-in mounting flanges facilitate installation and minimize chance of water leaks.
Contact:Marvair, Cordele, Ga.; 229-273-3636; 229-273-5154 (fax); dshuford@airxcel.com; www.marvair.com.
eProduct 214
Maytag
Model:M1200 PGC2MQ iQ Drive modulating furnaceFootprint (inches):Manufacturer did not specify.
Serviceability features:Color-coded wire harness is designed to fit the components, all with quick-connect fittings for service and replacement. Flexible category IV venting system may be vertically or horizontally vented using either a one- or two-pipe system for flexibility. Diagnostic lights for troubleshooting without counting flashes. Dedicated light for flame signal strength; two lights in combination indicate all other fault codes with easier-to-recognize states. Integrated control board includes connections for electronic air cleaner and humidifier. Two-piece door design uses captured screws to prevent losing door screws.
Technical support:Available at 866-462-9824 Monday-Friday, 8 a.m.-4:30 p.m. Central.
Technical support materials:Technical specs and installation guides available 24/7 on literature library at www.nordyne.com.
Noise-reduction features:Sealed blower compartment door reduces air leakage; insulated for quieter operation.
IAQ equipment supported:Modulating technology allows furnace to run longer at lower speeds for a more uniform, more comfortable mix of air and better filtration.
Thermostat compatibility:Requires a special thermostat.
Replacement parts compatibility:Some shared parts, some unique.
Additional features:The iQ drive furnace can modulate from 15-100 percent of capacity, offsetting heating demands of the home. Furnace includes iSEER, an efficient, brushless DC (ECM) motor that gives up to a 1-SEER-point efficiency gain in cooling.
Warranty information:With product registration, 12-year parts and 12-year Dependability Promise to replace the entire unit if the heat exchanger fails.
Special installation requirements:Contractors must be factory trained before they can purchase this furnace.
Contact:Nordyne, O’Fallon, Mo.; attn: Matt Lattanzi, 800-422-4328; 636-561-7399 (fax); res_sales@nordyne.com; www.maytaghvac.com.
eProduct 215
Footprint (inches):31 (length) by 31 (width) by 33 (height)
Serviceability features:Easier compressor and control access designed to make servicing easier for the contractor. Access panels are provided to all controls and the compressor from the side of the unit; iQ Drive thermostat provides system diagnostics.
Technical support:Available at 866-462-9824 Monday-Friday, 8 a.m.-4:30 p.m. Central.
Technical support materials:Technical specs and installation guides available 24/7 on literature library at www.nordyne.com.
Noise-reduction features:Compressor sound blanket, swept-wing fan blade, one-piece top/orifice. Modulating compressor also reduces noise. Unit can operate as low as 59 dB.
IAQ equipment supported:The iQ Drive delivers whole-home comfort through its built-in dehumidification features. The dehumidification technology is patented. Homeowners can set a desired humidity level based on their needs (35-70 percent).
Thermostat compatibility:Requires a special thermostat.
Replacement parts compatibility:Some shared parts, some unique.
Additional features:Up to 22 SEER with sound ratings of 59- 72 dB, depending upon operating conditions. Inverter-driven rotary compressor provides fully variable operation (40-118 percent of capacity).
Warranty information:With product registration, 12-year parts and 12-year Dependability Promise to replace the entire unit if the compressor fails. All split-system products must be installed with a matched indoor air handler or indoor coil to qualify.
Special installation requirements:Contractors must be iQ Drive certified before they can purchase this system.
Contact:Nordyne, O’Fallon, Mo.; attn: Matt Lattanzi, 800-422-4328; 636-561-7399 (fax); res_sales@nordyne.com; www.maytaghvac.com.
eProduct 216
Mitsubishi
Model:Mr. Slim H2i Hyper-heating Inverter P-Series Systems PUZ-HA30~36NHA2 outdoor unit with PLA-A30~36BA, PKA-A30~36HA(L)/KA(L), and PCA-A30~36KA indoor unitsFootprint (inches):14 (length) by 37 (width) by 53 (height)
Serviceability features:Service diagnostics are available through special tool or via controller. Easier access to internal components through panels. Four-way piping connections allow for connections from four directions. Outdoor unit powers the indoor units through a three-wire-plus ground system. Generally systems are easier to maintain and have a long life span. Little to no ductwork is required.
Technical support:Call 866-840-4822 for 24-hour automated technical support or 877-391-5550 for personal technical assistance, 8 a.m.-7 p.m. Eastern.
Technical support materials:Technical data book, service manuals, installation manuals, operation manuals.
Noise-reduction features:Fan blades for indoor and outdoor units are designed for low operation sound.
IAQ equipment supported:All indoor units include standard filters. Higher efficiency filters are available for PLA and PCA as options.
Thermostat compatibility:Indoor units are shipped with either an advanced wireless or wired remote controller, depending on the style of indoor unit.
Replacement parts compatibility:Some shared parts, some unique.
Additional features:H2i outdoor unit can operate down to -31F without cutoff. Units produce 100 percent of rated heating capacity at 5°F and 89 percent at -13°F outdoor ambient temperatures. Updated version of the Mr. Slim H2i Hyper-heating Inverter P-Series connected to the updated PCA and PKA updated IDUs, as well as the PLA IDUs. PUZ-HA-NHA2 H2i outdoor units (30 and 36) qualify for Energy Star Tier 2 with the new PKA-KA, new PCA-KA, and PLA-BA indoor units (six systems total). PUZ-HA36-NHA2 H2i outdoor unit with PLA-A36BA indoor unit qualify for tax credit (one system total).
Warranty information:Five-years parts and defect, seven-years compressors.
Special installation requirements:Manufacturer did not specify.
Contact:Mitsubishi Electric HVAC, Suwanee, Ga.; attn: Barbara Renaud, 678-376-2868; 678-376-2890 (fax); brenaud@hvac.mea.com; www.mehvac.com.
eProduct 217
Footprint (inches):11 (length) by 32 (width) by 22 (height)
Serviceability features:Complete built-in self-diagnostics direct a tech to a specific issue; washable filters speed up routine maintenance; convenient front, side, and top panels allow for easier access to serviceable components; reliable system components.
Technical support:Available at 877-391-5550, 8 a.m.-7 p.m. Eastern
Technical support materials:Service manuals, parts manuals
Noise-reduction features:The outdoor unit is extremely quiet thanks to the inverter-driven compressor, which features rotation frequency modulation plus low starting and stopping rotation.
IAQ equipment supported:Triple-filter protection (standard air filter, platinum deodorizing filter, anti-allergy enzyme filters).
Thermostat compatibility:Works with Mitsubishi Electric wireless remote controller (Mr. Slim M-Series), which offers enhanced features beyond thermostat capabilities, like dry mode for controlling humidity and powerful mode for rapid setpoint satisfaction.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:Guaranteed operation range is down to -13°F/-25°C. Very high efficiencies: Both models qualify for Energy Star and tax credit; next generation of popular FD models; includes i-see sensor technology; optional base heater; protection in the form of cutout at -18°F (to avoid thermistor error).
Warranty information:Five-years parts and defects and seven-years compressors.
Special installation requirements:Installation is straightforward and easier using standard industry tools and equipment. A factory service and install training class is offered to make the job even easier.
Contact:Mitsubishi Electric HVAC, Suwanee, Ga.; attn: Barbara Renaud, 678-376-2868; 678-376-2890 (fax); renaud@hvac.mea.com; www.mehvac.com.
eProduct 218
Napoleon Fireplaces
Model:GDS60-1 stoveFootprint (inches):20 (length) by 27 (width) by 31 (height)
Serviceability features:Manufacturer did not specify.
Technical support:Technical support can be found on Website under Tech Services, by calling 888-721-8324, or by e-mailing ask@napoleon.on.ca.
Technical support materials:All technical support materials can be found and downloaded from Website.
Noise-reduction features:Manufacturer did not specify.
IAQ equipment supported:The GDS60-1 is a direct-vent unit, vents through a wall or roof and uses outside combustion air. A patented B-vent adaptor kit conveniently modifies the direct vent stove into a conventional B-vent unit.
Thermostat compatibility:Requires a special thermostat.
Replacement parts compatibility:Some shared parts, some unique.
Additional features:The GDS60-1 cast iron gas stove is in popular demand for its performance and heating efficiencies. Its fine detailing and sleek outer casting design sets it apart from other cast iron gas stoves. It features a fuel-saving electronic ignition and ACS (anti-condensation switch), which controls pilot usage for cold-climate installations.
Warranty information:Every fireplace, stove, and insert is designed and manufactured to strict quality testing standards and backed by the President’s Limited Lifetime Warranty. (Registered under the world recognized ISO 9001-2008.)
Special installation requirements:All installation requirements can be found in product manuals on the Website.
Contact:Napoleon Fireplaces, Barrie, Ont., Canada; attn: Roger Gripton, 705-721-1212; 705-722-6031 (fax); rgripton@napoleonproducts.com; www.napoleonfireplaces.com.
eProduct 219
NuTone
Model:DF6SF iHybrid package unitFootprint (inches):55 (length) by 47 (width) by 43 (height)
Serviceability features:Compact footprint/low profile makes the unit easier to handle and transport. Accessible service ports give access to refrigerant system without disrupting operation. Access to controls and major components: Easier in and out service.
Technical support:Available at 800-422-4328 Monday-Friday, 8 a.m.-4:30 p.m. Central.
Technical support materials:Technical specs and installation guides available 24/7 on literature library via www.nordyne.com.
Noise-reduction features:The variable-speed motor allows for quiet operation and improved air quality. Low-vibration, 24-inch fan blade combined with custom venturi condenser fan. Compressor sound blanket for quieter operation.
IAQ equipment supported:Manufacturer did not specify.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:The iHybrid can heat with gas or electric depending on the outdoor temperature, maximizing energy bill savings. ECM variable-speed motor automatically adjust to different static loads. Smaller panels, great fit and finish, total seal, and quality construction. Drip edge on top panels whisks away rainwater. Embossed bottom pan keeps blower compartment dry. Factory-installed thermal expansion valve provides precise refrigerant control under varying load conditions. Hot surface appliance-type igniter with a 20-year history of reliability. Uses SmartLite® technology.
Warranty information:With product registration, 10-year parts, and 10-year Quality Pledge to replace the entire unit if the compressor or heat exchanger fails.
Special installation requirements:None.
Contact:Nordyne, O’Fallon, Mo.; attn: Dave Garvin, 800-422-4328; 636-561-7399 (fax); res_sales@nordyne.com; www.nutonehvac.com.
eProduct 220
Footprint (inches):Manufacturer did not specify.
Serviceability features:Color-coded wire harness is designed to fit the components, all with quick-connect fittings for service and replacement. Flexible category IV venting system may be vertically or horizontally vented using either a one- or two-pipe system. Diagnostic lights offer troubleshooting without counting flashes. A dedicated light for flame signal strength; two lights in combination indicate all other fault codes with easier-to-recognize states. Integrated control board includes connections for electronic air cleaner and humidifier. Two-piece door design uses captured screws to prevent losing door screws.
Technical support:Available at 800-422-4328, Monday-Friday, 8 a.m.-4:30 p.m. Central.
Technical support materials:Technical specs and installation guides available 24/7 on literature library via www.nordyne.com.
Noise-reduction features:Sealed blower compartment door reduces air leakage and is insulated for quiet operation.
IAQ equipment supported:Modulating technology allows furnace to run longer at lower speeds for a more uniform, comfortable mix of air and better filtration.
Thermostat compatibility:Requires a special thermostat.
Replacement parts compatibility:Some shared parts, some unique.
Additional features:The furnace can modulate from 15-100 percent of capacity, offsetting the heating demands of the home. Furnace includes iSEER, an energy-efficient brushless DC (ECM) motor that gives up to a 1-SEER-point efficiency gain in cooling.
Warranty information:With product registration, 10-year parts and 10-year Quality Pledge to replace the entire unit if the heat exchanger fails.
Special installation requirements:Contractors must be factory trained before they can purchase this furnace.
Contact:Nordyne, O’Fallon, Mo.; attn: Matt Lattanzi, 800-422-4328; 636-561-7399 (fax); res_sales@nordyne.com; www.nutonehvac.com.
eProduct 221
Payne
Model:PG9YA furnaceFootprint (inches):29 (length) by 19 (width) by 40 (height)
Serviceability features:Easier-to-access blower. Blower door interlock switch interrupts electrical power to the furnace when the blower door is removed.
Technical support:Available at 888-417-2963.
Technical support materials:Wiring diagrams, service/troubleshooting information, installation data, parts and part numbers, accessory kits.
Noise-reduction features:The cabinet design helps ensure quieter operation with two doors and an insulated cabinet.
IAQ equipment supported:Unit is equipped with electronic air cleaner and humidifier terminals.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:This single-stage condensing furnace provides affordable, reliable, and quiet operation; lower utility bills; and minimal maintenance.
Warranty information:This warranty is to the original purchasing owner only and is not transferable. Except as otherwise stated, if the product is installed in an owner-occupied, single-family residence and is properly registered within 90 days after original installation, then the warranty period will be 10 years from the date of installation. Otherwise the warranty period is five years from the date of installation. The warranty period on the heat exchangers is 20 years. In jurisdictions where warranty cannot be conditioned on registration, the warranty is 10-years parts limited.
Special installation requirements:Manufacturer did not specify.
Contact:Carrier Corp., Indianapolis; attn: Payne Customer Service, 888-417-2963; www.payne.com.
eProduct 222
Peerless
Model:Purefire®; PF-50, PF-80, PF-110, PF-140, PF-210, and PF-399 hot water boilerFootprint (inches):14-28 (length) by 17 (width) by 30-41 (height)
Serviceability features:Status display uses plain English instead of code numbers. Condensate collector has built-in neutralizer and float switch. Sleek jacket provides easier-to-access controls and visible system/boiler monitoring. Unit features leveling legs, outdoor sensor, and courtesy outlet. Dual flame sensing promotes reliable firing and safe operation.
Technical support:Available at 610-369-3208, 8 a.m.-4 p.m.
Technical support materials:All literature (installation data, wiring diagrams, etc.) is available online; click on the Resources tab.
Noise-reduction features:Modulating premix burners ensure quieter operation.
IAQ equipment supported:Sealed cabinet with direct outside air for combustion to prevent noises and odors from getting inside building.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Does not share replacement parts with other models.
Additional features:The boiler control and status display use plain-English text and are preset with common default values for contractor set-up. The control can be programmed for a variety of energy-saving features.
Warranty information:One-year warranty. A one-year parts-and-labor warranty will also be provided (labor coverage starting on day 31) if the warranty registration card is returned. In addition, the heat exchanger is covered by a 12-year limited warranty. Visit Website for details.
Special installation requirements:Access to drain or pump for condensate removal.
Contact:Peerless Boilers, Bally, Pa.; 610-845-6130; 610-845-6121 (fax); marketing@peerlessboilers.com; www.peerlessboilers.com.
eProduct 223
Quietside Corp.
Model:QSHE09 mini split heat pumpFootprint (inches):31 (length) by 9 (width) by 21 (height)
Serviceability features:The system uses line voltage for controlling the indoor unit, which makes for easier troubleshooting.
Technical support:Phone and live chat support available Monday-Friday, 8 a.m. Eastern to 5 p.m. Pacific.
Technical support materials:Installation manuals, service manuals, and owner manuals are available for download from the Website.
Noise-reduction features:Designed for overall quiet operation with 55-dB maximum for the condenser and 42-dB level for the evaporator.
IAQ equipment supported:Washable filters standard.
Thermostat compatibility:Requires a special thermostat. Wireless remote control.
Replacement parts compatibility:Some shared parts, some unique.
Additional features:The brand is known for its high value and dependability. Customers can enjoy cooling and heating efficiency with a moderate investment.
Warranty information:Five-years compressors, one-year parts, and 90 days limited labor.
Special installation requirements:Manufacturer did not specify.
Contact:Quietside Corp., Carlisle, Pa.; attn: Lee Gilpatrick, 717-243-2535; 717-243-7917 (fax); leeg@quietside.com; www.quietside.com.
eProduct 224
Raypak
Model:XPak Models 85 and 120 hydronic wall-hung boilerFootprint (inches):14 (length) by 16 and 18 (width) by 31 (height)
Serviceability features:Easier control access, raise from front; all of the components, just remove cover.
Technical support:Available through representative and service organization; see Website.
Technical support materials:All on Website, plus DVD on request.
Noise-reduction features:Maximum 60 dB.
IAQ equipment supported:Manufacturer did not specify.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:Introducing a smooth-tube, extruded aluminum alloy developed by Riello for the aircraft industry. Riello then incorporated this improvement into the XPak heat exchanger. Has been marketed successfully in Europe for over five years in more than 250,000 installations.
Warranty information:One-year parts, 20-year prorated heat exchanger.
Special installation requirements:Manufacturer did not specify.
Contact:Raypak, Inc., Oxnard, Calif.; attn: Stan Young, 805-558-0835; 805-278-5489 (fax); syoung@raypak.com; www.raypak.com.
eProduct 225
Rheem
Model:Classic® Series 95% AFUE gas furnace with Dual Comfort Control™, RGRMFootprint (inches):28 (length) by 18-25 (width) by 34 (height)
Serviceability features:Left- or right-side gas, electric, and condensate drainage connections make for easier installation. The heat exchanger is constructed of stainless steel for corrosion resistance and thermal fatigue reliability. The integrated furnace control board provides diagnostic information for service.
Technical support:Contact distributor for installation help.
Technical support materials:Consumer literature, sales fact sheet, spec sheet, tax credit form.
Noise-reduction features:An insulated blower compartment, slow-opening gas valve, and a specially designed inducer system.
IAQ equipment supported:The furnace is equipped with a permanent, washable filter for ease of maintenance and good IAQ. Its compact stature and low profile allow room for optional IAQ products to be installed. Compatible with the complete line of IAQ accessories.
Thermostat compatibility:Compatible with most thermostats. Two-stage thermostat is recommended for optimal performance.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:Classic Series furnace allows contractors to offer a highly efficient product that is available at a more affordable price due to several incentives. The unit may qualify for a manufacturer’s rebate of up to $1,000 through the CashBack program, and most models qualify for a federal tax credit of up to $1,500.
Warranty information:Limited lifetime heat exchanger, 10-year parts limited, and a 10-year conditional unit replacement warranty with registration.
Special installation requirements:Manufacturer did not specify.
Contact:Rheem, Atlanta; attn: Ed Raniszeski , 770-351-3000; 770-351-3260 (fax); ed.raniszeski@rheem.com; www.rheem.com.
eProduct 226
Footprint (inches):45 (length) by 31 (width) by 33 (height)
Serviceability features:Equipped with the Comfort Control² System, a new HVAC control panel that offers detailed system status displays and serial communications. A control board located on the unit features an easier-to-read, dual seven-segment LED that provides up to 37 individual fault codes, allowing contractors to diagnose system problems.
Technical support:Contact distributor for assistance.
Technical support materials:Consumer literature, sales fact sheet, spec sheet, tax credit form.
Noise-reduction features:A base pan elevates the unit off the pad and away from condensation, resulting in quieter performance and lower vibration levels. Equipped with compressor sound blankets to reduce noise.
IAQ equipment supported:When matched with a Prestige Series air handler, the system adjusts airflow to help control humidity for comfort in the cooling mode.
Thermostat compatibility:Compatible with most thermostats. The 500 Series thermostat provides maximum benefits and serial communication capabilities.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:The unit offers a solution for busy homeowners who demand high quality and efficiency. Active system protection, fault recall, and on-board diagnostics ensure ease of service.
Warranty information:Ten-years compressor, 10-year parts, and 10-year unit replacement guarantee.
Special installation requirements:When a Series 500 thermostat is used in tandem with the unit, the contractor can set up the system, simultaneously monitor the air handler and heat pump, and customize home comfort settings from one location. Simplifying these procedures streamlines the installation and maintenance process.
Contact:Rheem, Atlanta, Ga.; attn: Ed Raniszeski, 770-351-3000; 770-351-3260 (fax); ed.raniszeski@rheem.com; www.rheem.com.
eProduct 227
Ruud
Model:Achiever® Series gas furnace with Dual Comfort Control™, UGRMFootprint (inches):28 (length) by 18-25 (width) by 34 (height)
Serviceability features:Left- or right-side gas, electric, and condensate drainage connections for easier installation. The heat exchanger is all stainless steel for corrosion resistance and thermal fatigue reliability. The integrated furnace control board provides diagnostic information for service.
Technical support:Contact distributor for installation help.
Technical support materials:Consumer literature, sales fact sheet, spec sheet, tax credit form.
Noise-reduction features:An insulated blower compartment, slow-opening gas valve, and specially designed inducer system make it one of the quietest furnaces, said the company.
IAQ equipment supported:The furnace is equipped with a permanent, washable filter for maintenance and good IAQ. Its compact stature and low profile allow room for optional IAQ products to be installed. The furnace is compatible with the complete line of IAQ accessories.
Thermostat compatibility:Compatible with most thermostats. A two-stage thermostat is recommended.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:The Classic Series furnace allows contractors to offer a highly efficient product that is available at a more affordable price due to several incentives. The RGRM qualifies for a manufacturer’s rebate of up to $1,000 through the CashBack program, and most models qualify for a federal tax credit of up to $1,500.
Warranty information:Limited lifetime heat exchanger, 10-year parts limited, and 10-year conditional unit replacement warranty with registration.
Special installation requirements:Manufacturer did not specify.
Contact:Ruud, Atlanta; attn: Ed Raniszeski, 770-351-3000; 770-351-3260 (fax); ed.raniszeski@rheem.com; www.rheem.com.
eProduct 228
Footprint (inches):45 (length) by 31 (width) by 33 (height)
Serviceability features:Equipped with the Comfort Control² system, a new control panel that offers detailed system status displays and serial communications. A control board located on the unit features an easier-to-read, dual seven-segment LED that provides up to 37 individual fault codes, allowing contractors to diagnose system problems.
Technical support:Contact distributor for assistance.
Technical support materials:Consumer literature, sales fact sheet, spec sheet, tax credit form.
Noise-reduction features:A base pan elevates the unit off the pad and away from corrosive condensation, resulting in quieter performance and lower vibration levels. Compressor sound blankets reduce compressor noise.
IAQ equipment supported:When matched with an Ultra Series air handler, the system adjusts airflow to help control humidity for comfort in the cooling mode.
Thermostat compatibility:Compatible with most thermostats. The 500 Series thermostat provides maximum benefits and serial communication capabilities.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:The UPRL-JEC offers solutions for busy homeowners who demand high quality and efficiency. Active system protection, fault recall, and on-board diagnostics ensure ease of service.
Warranty information:Ten-years compressor, 10-year parts, and 10-year unit replacement guarantee.
Special installation requirements:When a Series 500 thermostat is used, the contractor can set up the system, monitor the air handler and heat pump, and customize home comfort settings from one location. Simplifying these procedures streamlines installation and maintenance.
Contact:Ruud, Atlanta; attn: Ed Raniszeski , 770-351-3000; 770-351-3260 (fax); ed.raniszeski@rheem.com; www.rheem.com.
eProduct 229
Samsung
Model:Slim Duct EH035CAV heat pumpFootprint (inches):31 (length) by 11 (width) by 22 (height)
Serviceability features:Flared pipe connections, easier access to electrical connections, self diagnostics on both indoor and outdoor units.
Technical support:Available 8 a.m.-5 p.m. Eastern at 866-243-6498; 8 a.m.-5 p.m. Pacific at 888-699-6067.
Technical support materials:Installation, service, and owner manuals are available in PDF form at Website.
Noise-reduction features:The series has a maximum 53 dB for the 1-ton condenser. Matching evaporator units have a 40-dB maximum rating.
IAQ equipment supported:Manufacturer did not specify.
Thermostat compatibility:Requires a special thermostat. Remote control supplied.
Replacement parts compatibility:Some shared parts, some unique.
Additional features:Ducted evaporators are available in a range of sizes, allowing greater flexibility in residential and commercial applications.
Warranty information:Five-years compressor, three-years parts, 120 days limited labor.
Special installation requirements:Line set allowances must be adhered to; appropriate application sizing delivers the best results.
Contact:Quietside Corp., Carlisle, Pa.; attn: Lee Gilpatrick, 717-243-2535; 717-243-7917 (fax); leeg@quietside.com; www.quietside.com.
eProduct 230
Sanyo Commercial Solutions
Model:12XHS71 mini split systemFootprint (inches):24 (length) by 24 (width) by 12 (height)
Serviceability features:Accessible electrical and refrigerant connections.
Technical support:Available Monday-Friday, 8:30 a.m.-5:30 p.m. Eastern at 800-851-1235.
Technical support materials:Installation, instruction, technical service manuals, parts breakdowns, and wiring diagrams available in PDF format online.
Noise-reduction features:Low operating sound with metering device located in outdoor unit.
IAQ equipment supported:Washable polypropylene air filter.
Thermostat compatibility:Requires a special thermostat.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:Indoor unit dimensions of 24 by 24 inches eliminate need for ceiling modifications. Fits in standard drop-ceiling openings.
Warranty information:Six-year compressor, one-year parts.
Special installation requirements:Manufacturer did not specify.
Contact:Sanyo Commercial Solutions, Wood Dale, Ga.; attn: Lauren Monitz, 678-355-6635; 678-355-6684 (fax); lmonitz@sna.sanyo.com; http://us.sanyo.com./hvac.
eProduct 231
Tappan
Model:FG7T iSeer furnaceFootprint (inches):Manufacturer did not specify.
Serviceability features:Color-coded wire harness is designed to fit the components, all with quick-connect fittings for service and replacement. Flexible category IV venting system may be vertically or horizontally vented using either a one- or two-pipe system for flexibility. Diagnostic lights for troubleshooting without counting flashes. Dedicated light for flame signal strength; two lights in combination indicate all other fault codes with easier-to-recognize stats. Integrated control board includes connections for electronic air cleaner and humidifier. Two-piece door design uses captured screws to prevent losing door screws.
Technical support:Available at 800-422-4328 Monday-Friday, 8 a.m.-4:30 p.m. Central.
Technical support materials:Technical specs and installation guides available 24/7 on literature library via www.nordyne.com.
Noise-reduction features:Sealed blower compartment door reduces air leakage; insulated for quiet operation.
IAQ equipment supported:Two-stage, variable-speed technology allows furnace to run longer at lower speeds for a more uniform, comfortable mix of air and better filtration.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:Furnace includes iSEER, an energy-efficient brushless DC (ECM) motor that gives up to a 1-SEER-point efficiency gain in cooling. Its low height makes it easier to install in low-ceiling applications, works well with taller high-SEER coils, and is easier to handle and install.
Warranty information:With product registration, 10-year parts and 10-year Quality Pledge to replace the entire unit if the heat exchanger fails.
Special installation requirements:None.
Contact:Nordyne, O’Fallon, Mo.; attn: Matt Lattanzi, 800-422-4328; 636-561-7399 (fax); res_sales@nordyne.com; www.tappan.net.
eProduct 232
Footprint (inches):55 (length) by 47 (width) by 43 (height)
Serviceability features:Convertible air delivery (horizontal or downflow to accommodate rooftop or horizontal application). Accessible service ports: Quick access to refrigerant system without disrupting operation. Access to controls and major components. High- and low-pressure controls protect compressor operation.
Technical support:Available at 800-422-4328 Monday-Friday, 8 a.m.-4:30 p.m. Central.
Technical support materials:Technical specs and installation guides available 24/7 on literature library via www.nordyne.com.
Noise-reduction features:The variable-speed motor allows for extra quiet operation and improved air quality. Low vibration, 24-inch fan blade combined with custom venturi condenser fan. Compressor sound blanket.
IAQ equipment supported:Manufacturer did not specify.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:ECM variable-speed motor allows the motor to automatically adjust to different static loads. Smaller panels, great fit and finish, total seal, well designed, quality construction. Drip edge on top panels removes rainwater. Embossed bottom pan keeps blower compartment dry. Factory-installed thermal expansion valve provides refrigerant control under varying loads. Hot surface appliance-type igniter with a 20-year history of reliability. Utilizes SmartLite® technology.
Warranty information:With product registration, 10-year parts and 10-year Quality Pledge to replace the entire unit if the compressor or heat exchanger fails.
Special installation requirements:None.
Contact:Nordyne, O’Fallon, Mo.; attn: Dave Garvin, 800-422-4328; 636-561-7399 (fax); res_sales@nordyne.com; www.tappan.net.
eProduct 233
Tempstar
Model:PGS4 package gas/electric unitFootprint (inches):33-44 (length) by 48 (width) by 40-54 (height)
Serviceability features:Three separate service panels, clearly marked with embossed symbols, offer easier access to the compressor, blower compartment, and control box. Service techs can keep the unit on while running diagnostics, since they can have one panel open with others closed.
Technical support:Factory-trained Technical Service Advisors (TSAs) on staff at local distributors provide technical assistance, troubleshooting at the local level.
Technical support materials:Product information posted online at dealer Website includes product spec sheets, installation-operation manuals, and technical support/parts manuals. Technical support materials are also available from local distributors.
Noise-reduction features:Quieter operation is a result of additional stability provided by newly designed, formed top panel.
IAQ equipment supported:Dehumidification cooling speed standard on control board. Internal filter kits available as accessories.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:Eligible for the 2009-2010 U.S. HVAC tax credit for efficient fans. Compact units fit in bed of standard pick-up truck. Full-perimeter steel base rails give units extra stability for loading and transporting. Stainless steel heat exchanger. X-13 indoor blower motor delivers efficient airflow. Hail guard standard.
Warranty information:Seven-year No Hassle Replacement™ limited warranty; lifetime limited heat exchangers; 10-year parts limited including compressor with timely registration (restrictions apply; see warranty certificate for details). To learn more about all of these limited warranties, go to www.gotempstar.com and click on the “Warranty” tab on the menu.
Special installation requirements:Metal base rails for rigging (roof installations).
Contact:International Comfort Products (ICP) LLC, Nashville, Tenn.; attn: John Mott, 800-315-4370; 615-383-2215 (fax); john.mott@mottpr.com; www.gotempstar.com.
eProduct 234
Footprint (inches):29 (length) by 19-25 (width) by 40 (height)
Serviceability features:These low-profile furnaces are designed with easier-to-remove doors and spacious service compartments to give techs room to work. Furnace includes a built-in electronic diagnostic system that can be used while the furnace is running. Most hose and clamp connections are premade by the factory, reducing installation time.
Technical support:Factory-trained Technical Service Advisors (TSAs) on staff at local distributors provide technical assistance, troubleshooting at the local level.
Technical support materials:Product information posted online at dealer Website includes product spec sheets, installation-operation manuals, and technical support/parts manuals. Technical support materials are also available from local distributors.
Noise-reduction features:The one-piece steel cabinet is thermal lined; an insulated blower compartment adds sound protection. Solid stainless steel doors provide a sealed combustion compartment. The unit has two-stage heating, so it operates in the quieter first stage 70-80 percent of the time.
IAQ equipment supported:Predrilled accessory holes and convenient wiring hook-ups make it easier to add humidifiers, electronic air cleaners, and other accessories.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:Eligible for the 2009-10 U.S. HVAC tax credit. Four-position furnace provides the efficiency, quiet operation, and comfort of variable-speed, two-stage heating. Meets California low-NOx emissions standards. Variable-speed blower motor cuts electricity costs. One- or two-pipe venting. Troubleshooting LED fault indicator easier to view through sight glass in blower door.
Warranty information:Ten-year No Hassle Replacement™ limited warranty; lifetime limited heat exchangers; 10-year parts limited with timely registration (restrictions apply; see warranty certificate for details). To learn more about all of these limited warranties, go to www.gotempstar.com and click on the “Warranty” tab on the menu.
Special installation requirements:Shipped as natural gas in upflow configuration; all parts included for downflow, horizontal-left and right with no need for accessory conversion kits. LP gas kits available.
Contact:International Comfort Products (ICP), LLC, Nashville, Tenn.; attn: John Mott, 800-315-4370; 615-383-2215 (fax); john.mott@mottpr.com; www.gotempstar.com.
eProduct 235
Tetco Geothermal
Model:ESIII geothermal package unitFootprint (inches):26-31 (length) by 22-28 (width) by 50-60 (height)
Serviceability features:Eight access panels, removable low-voltage terminal strips, LED fault lights, flow switch protected, Schrader-mounted pressure switches, stab-in plenum heater.
Technical support:Design and application support, 24-hour technical support.
Technical support materials:Full specification catalogs, installation manuals, wiring diagrams, brochures.
Noise-reduction features:Eco-friendly, recycled, foil-backed denim insulation, grommet-mounted compressors.
IAQ equipment supported:E-coated air coils, ECM blowers, dehumidification control, pleated filters, stainless steel drain pans, foil-backed denim insulation (not fiberglass).
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:Solid quality construction, high efficiencies and capacities, quiet operation, and superior sales and support.
Warranty information:Five-years refrigerant circuit, two-year all parts, two-year labor (dealer warrants first year). Optional 10/5/3 year warranty available.
Special installation requirements:Manufacturer did not specify.
Contact:Enertech Manufacturing, LLC, Greenville, Ill.; attn: Dave Salyer, 618-664-9010; 618-664-4597 (fax); dsalyer@enertechmfg.com; www.tetco-geo.com.
eProduct 236
Thermo Pride
Model:OH8 furnaceFootprint (inches):37 (length) by 25 (width) by 50 (height)
Serviceability features:PSC blower motor standard, ECM blower is an available option. Dual cleanouts placed for easier access, control board mounted at front of cabinet for easier access, flame observation door for easier burner flame viewing.
Technical support:Available at 800-348-5130, 8 a.m.-5 p.m. Central.
Technical support materials:Installation and operating manual includes parts lists, wiring diagrams, troubleshooting.
Noise-reduction features:Manufacturer did not specify.
IAQ equipment supported:Manufacturer did not specify.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Some shared parts, some unique.
Additional features:Higher heating and cooling capacities with a low-profile, highboy design
Warranty information:Limited lifetime warranty heat exchanger (transferrable to future homeowners), 10-year parts.
Special installation requirements:Manufacturer did not specify.
Contact:Thermo Products, North Judson, Ind.; 574-896-2133; 574-896-5301 (fax); tpmarketing@thermopride.com; www.thermopride.com.
eProduct 237
Trane
Model:XC95m modulating furnaceFootprint (inches):28 (length) by 18, 21, or 25 (width) by 40 (height)
Serviceability features:Communicating user interface. Quarter-turn blower door latches on upflow models. Self-diagnostic control. Compatible with SEER outdoor units.Technical support:Contact local distributor.
Technical support materials:The “ComfortSite” intranet site for dealers and distributors allows quick access to the most current support materials (catalog pages, installer guides, service facts, dealer sheets, product data, submittals, and owners manuals).
Noise-reduction features:Steel insulated cabinet. Insulated panels help hold more heat in the furnace, ensure greater durability, and reduce operating sound.
IAQ equipment supported:CleanEffects™ air filtration removes more dust, pollen, and other irritants from conditioned air. It is proven to remove more than 99 percent of the common flu, or influenza A virus, from a home’s filtered air.
Thermostat compatibility:Compatible with most thermostats. Requires XL900 for communicating capability.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:Fully modulating furnace with 1-percent demand increments. Real-time modulation in communicating mode. Modulation based on indoor temperature. Similar to cruise control - set it and forget it. Does not overshoot the set temperature. Provides 24-V capability with modulation.
Warranty information:Lifetime limited heat exchanger, 10-year limited on internal functional parts. If the product is not registered within 60 days of installation, base limited warranty terms apply. Optional extended warranties available. Extended warranties can pay for labor and other costs not covered by manufacturer’s limited warranty. Warranties are for residential use only, some exclusions may apply.
Special installation requirements:None.
Contact:Trane, Tyler, Texas; attn: Joyce Warrington, 903-581-3467; 903-581-9070 (fax); joyce.warrington@trane.com; trane.com.
eProduct 238
Footprint (inches):34 (length) by 37 (width) by 33, 41, or 45 (height)
Serviceability features:Quick-sess cabinet, service access, and refrigerant connections with full coil protection.
Technical support:Contact local distributor.
Technical support materials:The “ComfortSite” intranet site for dealers and distributors allows access to the most current support materials (catalog pages, installer guides, service facts, dealer sheets, product data, submittals, and owner manuals).
Noise-reduction features:Sound insulator on compressor.
IAQ equipment supported:CleanEffects™ air filtration removes more dust, pollen, and other irritants from conditioned air, and is now proven to remove more than 99 percent of the common flu virus from a home’s filtered air.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:The line gives dealers a new set of options to meet the Energy Star and tax credit requirements for builders and retail replacement contractors.
Warranty information:Ten-years limited compressor, 10-years limited outdoor coil, 10-years limited internal functional parts. The 10-year functional parts limited warranty extends to the indoor gas furnace, coil, air handler, and thermostat when installed as part of a complete XR comfort system, which includes an AHRI-certified matching outdoor XR unit, indoor unit, and thermostat installed at the same time. If the product is not registered within 60 days of installation, base limited warranty terms apply. Optional extended warranties available. Extended warranties can pay for labor and other costs not covered by manufacturer’s limited warranty.
Special installation requirements:None.
Contact:Trane, Tyler, Texas; attn: Joyce Warrington , 903-581-3467; 903-581-9070 (fax); joyce.warrington@trane.com; trane.com.
eProduct 239
WaterFurnace
Model:Envision™ NDW Series hydronic geothermal heat pumpFootprint (inches):34 (length) by 25.5 (width) by 24 (height)
Serviceability features:Features a user interface to diagnose system faults and alerts, compact cabinet, removable compressor access panels, quick-attach wiring harnesses, and high- and low-pressure refrigerant service ports for easier servicing and maintenance. Control panels that can be placed on either end improve serviceability.
Technical support:Dealer line is available at 888-929-2837, 7 a.m.-5:30 p.m. Eastern. Technical service pager is available after hours at 800-455-3624.
Technical support materials:Contractors have access to a secure site, where they can download specification manuals, installation manuals, service and troubleshooting guides, submittals, diagrams, and parts information.
Noise-reduction features:All interior cabinet surfaces are insulated with ½-inch-thick, 1 ½-lb density surface-coated, acoustic-type glass fiber insulation. Additionally, the compressors are mounted on double isolation plates made with acoustic steel and wrapped in a multidensity laminate-lined compressor blanket designed to suppress low-frequency noise and ensure quiet operation.
IAQ equipment supported:Manufacturer did not specify.
Thermostat compatibility:Manufacturer did not specify.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:The unit, which is designed to meet the high-volume water demands of larger homes, includes a microprocessor capable of working with building automation systems. It includes two single-speed scroll compressors for dual-capacity operation and the patented IntelliStart™ feature, which reduces the amount of current needed to start the unit by 70 percent. The units reduce annual water heating costs as much as 60 percent.
Warranty information:Standard 10-year parts-and-labor allowance.
Special installation requirements:The high efficiency of the unit means the series requires less loop than other products.
Contact:WaterFurnace International Inc., Fort Wayne, Ind.; attn: Ryan Stauffer, 800-934-5160; 866-272-4387 (fax); ryan.stauffer@waterfurnace.com; www.waterfurnace.com.
eProduct 240
Westinghouse
Model:FG7MQ iQ Drive modulating furnaceFootprint (inches):Manufacturer did not specify.
Serviceability features:Color-coded wire harness is designed to fit the components, with quick-connect fittings for service and replacement. Flexible category IV venting system may be vertically or horizontally vented using either a one- or two-pipe system. Diagnostic lights for troubleshooting without counting flashes. A dedicated light for flame signal strength; two lights in combination indicate all other fault codes with easier-to-recognize stats. Integrated control board includes connections for electronic air cleaner and humidifier. Two-piece door design uses captured screws to prevent losing door screws.
Technical support:Available at 800-422-4328 Monday-Friday, 8 a.m.-4:30 p.m. Central.
Technical support materials:Technical specs and installation guides available 24/7 on literature library via www.nordyne.com.
Noise-reduction features:Sealed blower compartment door to reduce air leakage, insulated for quieter operation.
IAQ equipment supported:Modulating technology allows furnace to run longer at lower speeds for a more uniform, comfortable mix of air and better filtration.
Thermostat compatibility:Requires a special thermostat.
Replacement parts compatibility:Some shared parts, some unique.
Additional features:The iQ Drive furnace can modulate from 100-15 percent of capacity, offsetting heating demands of the home. Furnace includes iSEER, an energy-efficient brushless DC (ECM) motor that gives up to a 1-SEER-point efficiency gain in cooling.
Warranty information:With product registration, 10-year parts, and 10-year Quality Pledge to replace the entire unit if the heat exchanger fails.
Special installation requirements:Contractors must be factory trained before they can purchase this furnace.
Contact:Nordyne, O’Fallon, Mo.; attn: Matt Lattanzi, 800-422-4328; 636-561-7399 (fax); res_sales@nordyne.com; www.westinghousehvac.com.
eProduct 241
Footprint (inches):55 (length) by 47 (width) by 43 (height)
Serviceability features:Convertible air delivery (horizontal or downflow to accommodate rooftop or horizontal application). Accessible service ports (quick access to refrigerant system without disrupting operation). Access to controls and major components: Easier service. High- and low-pressure controls protect compressor operation.
Technical support:Available at 800-422-4328 Monday-Friday, 8 a.m.-4:30 p.m. Central.
Technical support materials:Technical specs and installation guides available 24/7 on literature library via www.nordyne.com.
Noise-reduction features:The variable-speed motor allows for quieter operation and improved air quality. Low-vibration, 24-inch fan blade combined with custom venturi condenser fan. Compressor sound blanket for quiet operation.
IAQ equipment supported:Manufacturer did not specify.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:ECM variable-speed motor allows the motor to automatically adjust to different static loads. Smaller panels, great fit and finish, total seal, well designed, quality construction. Drip edge on top panels removes rainwater. Embossed bottom pan keeps blower compartment dry. Factory-installed thermal expansion valve provides refrigerant control under varying load conditions. Hot surface appliance-type igniter has 20-year history of reliability. Uses SmartLite® technology.
Warranty information:With product registration, 10-year parts, and 10-year Quality Pledge to replace the entire unit if the compressor or heat exchanger fails.
Special installation requirements:None.
Contact:Nordyne, O’Fallon, Mo.; attn: Dave Garvin, 800-422-4328; 636-561-7399 (fax); res_sales@nordyne.com; www.westinghousehvac.com.
eProduct 242
Whirlpool
Model:W4PG436A068A gas/electric package unitFootprint (inches):37 (length) by 65 (width)
Serviceability features:All controls are in sight for easier access, and accessible by removing side panels.
Technical support:Manufacturer did not specify.
Technical support materials:Technical publications such as specs, installation-operation manuals with troubleshooting charts, and parts lists with drawings are available from the distributors, or directly on the Whirlpool Gold™ dealer Website.
Noise-reduction features:Furnace cabinets are fully insulated for sound attenuation and insulation.
IAQ equipment supported:High-static blowers accommodate high-efficiency filtration systems.
Thermostat compatibility:Single-stage cooling, two-stage heating thermostat required.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:Scroll compressors and many years of reliable performance.
Warranty information:Five-years parts and 20-year limited heat exchanger.
Special installation requirements:All installation requirements are listed in the installation and operating instructions. Can be installed as a horizontal or down-discharge configuration.
Contact:Whirlpool/Tradewinds, Jacksonville, Fla.; attn: Chris Campbell, 904-407-4470; 775-369-6550 (fax); ccampbell@tradewindshvac.net; www.whirlpoolhvac.com.
eProduct 243
Footprint (inches):21 (length) by 29 (width)
Serviceability features:The WGFET Series gas furnace is serviced from the front of the cabinet by removing either of the two panels. All controls are in sight for easier access.
Technical support:Manufacturer did not specify.
Technical support materials:Technical publications such as specs, installation-operation manuals with troubleshooting charts, and parts lists with drawings are available from the distributors or directly on the Whirlpool Gold dealer Website.
Noise-reduction features:Furnace cabinets are fully insulated for sound attenuation and insulation.
IAQ equipment supported:Provides excellent fuel efficiency while being capable of supporting IAQ devices such as UV lights, electronic air cleaners, and humidifiers from the furnace control board.
Thermostat compatibility:Two-stage gas furnace will operate with either a single- or two-stage thermostat.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:Stainless steel with primary and secondary heat exchangers; should provide many years of reliable performance.
Warranty information:Five-years parts and limited lifetime heat exchanger. The gas furnaces are now covered by the HomeWise® HVAC limited warranty, which allows a replacement furnace if a furnace heat exchanger fails within the first five years following installation.
Special installation requirements:All installation requirements are listed in the installation and operating instructions. The furnace can be vented using Schedule 40 PVC in a one- or two-pipe vent configuration.
Contact:Whirlpool/Tradewinds, Jacksonville, Fla.; attn: Chris Campbell, 904-407-4470; 775-369-6550 (fax); ccampbell@tradewindshvac.net; www.whirlpoolhvac.com.
eProduct 244
York
Model:Affinity™ package product, DNZ, DNQFootprint (inches):49 (length) by 47 (width) by 33 (height)
Serviceability features:Slide-out blower assembly, external refrigerant pressure ports, high- and low-pressure safeties, control board with diagnostic indicator.
Technical support:The first level of support is provided by the distributor. Factory support is available to distributors and dealers by calling 877-874-7378, 7 a.m.-6 p.m. Central.
Technical support materials:Technical data, installation manual, wiring diagrams, and other support documentation can be found at www.upgnet.com.
Noise-reduction features:The low-sound, QuietDrive™ swept-wing fan system, along with an insulated cabinet and base pan, provide a product with very low noise and vibration transmission.
IAQ equipment supported:One-inch fiberglass filters are standard on the three-phase product and optional on the single- phase product. An optional factory- or field-installed filter rack will accommodate either 1- or 2-inch filters.
Thermostat compatibility:Compatible with most thermostats.
Replacement parts compatibility:Some shared parts, some unique.
Additional features:Both the new DNZ product and the 14-SEER/12-EER DNQ product include the new MicroChannel condenser coil technology. This technology is durable and corrosion resistant. It also requires less coil area and half the refrigerant charge required for standard copper tube, aluminum fin coil-equipped units.
Warranty information:The single-phase product carries a 10-year parts, 10-year compressor, and 20-year heat exchanger warranty. The three-phase product carries a one-year parts, five-year compressor, and 10-year heat exchanger warranty. Extended warranties are available on parts, compressors, and labor.
Special installation requirements:Duct configurations can be changed from sideflow (horizontal) to downflow (vertical) by moving prepainted, insulated panels from one position to another. All units accept gas, electric, and control service from the bottom or side of the unit.
Contact:Johnson Controls, Norman, Okla.; attn: Brian Wathen, 405-419-6557; 405-419-6593 (fax); brian.n.wathen@jci.com; www.yorkupg.com.
eProduct 245
Footprint (inches):30 (length) by 18, 21 or 25 (width) by 33 (height)
Serviceability features:The unit’s compact height fits in tight spaces. Quarter-turn knobs provide easier door removal, and solid removable bottom panels make conversion easier. Units feature easier access to controls to connect power/control wiring, fully supported blower assembly for easier access and blower removal, and high-level self diagnostics with fault code display.
Technical support:The first level of support is provided by the distributor. Factory support is available to distributors and dealers by calling 877-874-7378, 7 a.m.-5 p.m. Central.
Technical support materials:Technical guide, submittal data sheet, guide specs, installation instructions, user manual, and a parts list are available at www.upgnet.com or by request.
Noise-reduction features:The unit features quiet operation of the inducer and burner. An insulated blower compartment ensures quiet operation of the blower.
IAQ equipment supported:Variable-speed models feature ECM fan motors, which circulate air for longer time periods. This equates to consistent temperatures and longer periods of air filtering, resulting in cleaner, more comfortable air. External air filters offer maximum flexibility in meeting customer IAQ needs. Compatible with all York premium IAQ products.
Thermostat compatibility:Compatible with most thermostats. A selection of compatible thermostats is available to provide optimum performance and features for any installation. An adjustable delay timer allows two-stage operation with a single-stage thermostat.
Replacement parts compatibility:Shares replacement parts with other models.
Additional features:The unit’s height makes it easier to install in basements, closets, attics, and other tight spaces. It features a high-tech tubular aluminized steel primary heat exchanger with a stainless steel tube/aluminum fin secondary heat exchanger for efficiencies as high as 96 percent. All models qualify for the federal tax credit program for both AFUE and blower performance.
Warranty information:Lifetime heat exchanger, 10-year heat exchanger in commercial applications, and five-year limited parts. An extended 10-year limited parts warranty applies when the furnace is registered online within 90 days of purchase for replacement or closing for new home construction.
Special installation requirements:None; the smaller cabinet, convertible design, and no knockouts make this unit easier to install in replacement or new construction applications.
Contact:Johnson Controls, Norman, Okla.; attn: Jeff Hurt, York Brand Manager, 405-419-6563; 405-419-6545 (fax); jeffrey.n.hurt@jci.com; www.yorkupg.com.
eProduct 246
Publication date:09/14/2009
