The product grid (see the PDF link at the bottom of this article) includes technical facts such as fuel type, heater type, single or multi stage, and unit size.

American Standard Heating and Air Conditioning

Model: T/YHC067E3, 4 Precedent 17 Plus packaged unit

Footprint (in inches): 53 (length) by 89 (width)

Serviceability features: Colored and numbered wiring, easy access low-voltage terminal board (LTB), ReliaTel microprocessor controls, quick access panels, single side service, and standardized components.

Technical support: Contact local American Standard distributor.

Technical support materials: Wiring diagrams, service/troubleshooting information, installation data, and performance data.

Noise-reduction features: Foil-faced and edge captured insulation, and variable-speed, direct-drive motors.

IAQ equipment supported: Enhanced dehumidification functionality. Filters are standard on all units. Foil-faced and edge-captured insulation. IAQ dual sloped and removable drain pans. Variable-speed, direct-drive motors. Two-inch MERV 7 filters or 2-inch MERV 13 filters available as a factory-installed option.

Thermostat compatibility: Compatible with most thermostats. Enhanced functionality may be obtained using an American Standard zone sensor.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: Efficiency levels up to 17.2 SEER on select models (industry leading). Direct-drive electronically commutated motor (ECM) on all models (pre-programmed with enhanced comfort and energy curves). Unloading compressor (0, 67, and 100 percent). Single-zone VAV (comfort/efficiency) and enhanced dehumidification offering.

Warranty information: Five-year limited compressor, five-year limited heat exchanger, one-year limited parts standard. Extended warranties are available with parts and labor options.

Special installation requirements: Application of this product should be within the cataloged airflow and cooling considerations. The recommended clearances identified with unit dimensions should be maintained. Units have reversible sloped condensate drain pans. Units must be installed level. Any unit slope must be toward the side of unit where condensate drain is connected.

Contact: American Standard Heating and Air Conditioning, 903-581-3467; www.americanstandardair.com.

eProduct 160

Applied Air

Model: Fresh Air Package (FAP) packaged unit

Footprint (in inches): Manufacturer did not specify.

Serviceability features: All units are fully tested before leaving the factory. Wiring is color coded and labeled, refrigerant circuit includes service ports and filter/driers, full-sized hinged access doors to all major compartments; DDC controls provide service codes and optional trend analysis via Internet.

Technical support: Available from 7 a.m. to 5 p.m. Central time, Monday to Friday, at 214-819-5227. Factory-trained service contractors are located throughout North America.

Technical support materials: All units are shipped with complete IOM manuals, unit wiring diagrams permanently attached inside control compartment, and gas piping diagrams permanently attached inside control compartment. Units also include Microsoft tags inside control compartment that link directly to IOM manual for downloads available 24 hours a day, 7 days a week. Component part numbers specific to individual units (by serial number) are also available via the Mestek sales assistant website.

Noise-reduction features: Fan and motor assemblies can be ordered with full spring isolation and all units can be ordered with 1-inch thick insulation for sound reduction and thermal protection.

IAQ equipment supported: Designed from the ground up to handle 100 percent outside air so it is capable of a wide range of dehumidification depending upon model size. Units can include hot gas reheat coils, up to eight row cooling coils, and variable-speed compressors. Filter options allow up to four levels of filtration including up to MERV 15 primary filters. Units can also be ordered with an enthalpy wheel module.

Thermostat compatibility: Requires a special thermostat.

Replacement parts compatibility: Some shared parts and some unique parts.

Additional features: The modular design gives the design engineer flexibility to meet the project needs without having to resort to a fully custom system. Since the FAP was designed from the start to be a 100 percent outside air unit, it includes subtle design elements such as drain pan size and coil spacing that are intended to handle moisture removal effectively. The unit structure itself is designed to handle up to 6 inches of static pressure, providing a broad range of application possibilities.

Warranty information: The unit, as a whole, 12 months from startup or 18 months from shipment (parts only), 10-year heat exchanger, five-year parts. Extended warranties can be obtained.

Special installation requirements: Designed to be curb mounted. The curb is designed to meet the full perimeter of the unit so it is customized to the specific combination of modules that are selected. Depending upon unit capacity and modules selected, the unit may be shipped in sections. Each section is designed to mate to the adjacent section and pulled together at the base using the combination lifting lugs/connection lugs. The top seam includes a cover strip if necessary.

Contact: Mestex, Division of Mestek, 214-638-6010; www.mestex.com.

eProduct 161

Arcoaire

Model: RGS120 packaged gas/electric rooftop

Footprint (in inches): 88 (length) by 60 (width) by 49 (height)

Serviceability features: Units feature through-the-base utility connections capability. All connections and troubleshooting points located in one convenient place, the master terminal board. Access panels have easy grip handles and no-strip screw feature. Exclusive IGC solid-state control for onboard diagnostics with LED error code designation, burner control logic and energy saving indoor fan motor delay.

Technical support: Factory-trained Technical Service Advisors (TSAs) on staff at local distributors provide technical assistance, troubleshooting at the local level. ICP technical training is available at field schools held at participating distributor locations.

Technical support materials: Product information posted online at Arcoaire dealer website www.goarcoaire.com includes product specification sheets, installation, and operation manuals.

Noise-reduction features: Quiet and efficient operation is provided by belt-driven evaporator fans.

IAQ equipment supported: Two-inch return air filters. Optional economizer control accepts CO2 sensor for IAQ capability. Accessory duct-mounted CO2 sensor available for field installation to provide outdoor air for ventilation capability on demand (DCV).

Thermostat compatibility: Compatible with most thermostats.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: ASHRAE 90.1 compliant unit is field-convertible from vertical to horizontal airflow on all models with no special kit. Scroll compressor has internal line-break overload protection. Factory-installed options include three heat options (high, medium, and low), and medium and high static indoor fan option. Low NOx models include stainless steel heat exchangers.

Warranty information: 15-year limited stainless steel heat exchanger, 10-year limited aluminized heat exchanger, five-year limited compressor, one-year limited all other parts.

Special installation requirements: None.

Contact: International Comfort Products LLC (ICP), 800-315-4370; www.goarcoaire.com.

eProduct 162

Model: RHS150 packaged heat pump

Footprint (in inches): 116 (length) by 63 (width) by 57 (height)

Serviceability features: Units feature through-the-base utility connections capability. All connections and troubleshooting points located in one convenient place, the master terminal board. Access panels have easy grip handles and no-strip screw feature. Large laminated control wiring and power wiring drawings are affixed to unit to make troubleshooting easy.

Technical support: Factory-trained Technical Service Advisors (TSAs) on staff at local distributors provide technical assistance, troubleshooting at the local level. ICP technical training is available at field schools held at participating distributor locations.

Technical support materials: Product information posted online at Arcoaire dealer website www.goarcoaire.com includes product specification sheets, installation, and operation manuals.

Noise-reduction features: Quiet and efficient operation is provided by belt-driven evaporator fans. Fully insulated cabinet.

IAQ equipment supported: Two-inch return air filters. Optional economizer control accepts CO2 sensor for IAQ capability. Accessory duct-mounted CO2 sensor available for field installation to provide outdoor air for ventilation capability on demand (DCV).

Thermostat compatibility: Compatible with most thermostats.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: ASHRAE 90.1 compliant unit is convertible from downflow to horizontal. It features loss of charge, freeze-protection, and high-pressure switches. Scroll compressor has internal line-break overload protection. Factory-installed options available, including medium- and high-static indoor fan option. Fixed orifice metering devices on all models to precisely control refrigerant flow.

Warranty information: Five-year limited compressor; one-year limited all other parts.

Special installation requirements: Field accessory supply duct kit (CRDUCTCV001A00) required for conversion from downflow to horizontal airflow on 12.5-ton model.

Contact: International Comfort Products LLC (ICP), 800-315-4370; www.goarcoaire.com.

eProduct 163

Bard Mfg. Co.

Model: Step capacity gas/electric wall-mount, WG*S Series

Footprint (in inches): 27 (length) by 42 (width) by 88, 98 (height)

Serviceability features: All service and maintenance performed outside the building, consuming no interior floor space. Additional service features include step capacity compressor, multispeed blower motor, high- and low-pressure switches. Ventilation packaged options factory- or field-installed, 18-gauge stainless steel tubular heat exchanger, hinged service door allowing easy access to air filters, advanced in-shot burner design, integrated DSI control, versatility to satisfy ducted or nonducted application.

Technical support: Available through local Bard distribution network.

Technical support materials: Service parts guides, wiring diagrams, installation manuals (printed and CD formats), website.

Noise-reduction features: Quiet operation features include step-capacity compressor, ECM indoor blower motor, advanced design in-shot burners.

IAQ equipment supported: Variety of ventilation options include energy recovery ventilator, economizer, commercial room ventilator.

Thermostat compatibility: Compatible with most thermostats.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: Features a multistep capacity compressor with green refrigerant R-410A and ventilation package options. Its space saving-design is ideal for versatile applications such as new construction, modular applications, school modernization, portable structures, retail stores, correctional facilities, and other commercial applications.

Warranty information: Five-year parts, 10-year heat exchanger.

Special installation requirements: Low NOx models available, high-altitude kits, Canadian-approved models.

Contact: Bard Mfg. Co., 419-636-1194; www.bardhvac.com.

eProduct 164

Model: Wall-mount heat pump, T series

Footprint (in inches): 17, 22 (length) by 38, 42 (width) by 70, 84, 93 (height)

Serviceability features: All service and maintenance performed outside the building, consuming no interior floor space. Additional service features include variable-speed ECM blower motor, high- and low-pressure switches, compressor time delay. Ventilation package options factory or field-installed.

Technical support: Available through local Bard distribution network.

Technical support materials: Service parts guides, wiring diagrams, installation manuals (printed and CD formats), website.

Noise-reduction features: Acoustical sound accessories can be added for even lower operating sound levels as requirements and budgets dictate.

IAQ equipment supported: Variety of ventilation options include energy recovery ventilator, economizer, commercial room ventilator.

Thermostat compatibility: Compatible with most thermostats.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: One of the most efficient wall-mounted heat pumps on the market, with green refrigerant R-410A and special sound reduction technology. Ideal for new construction, modular applications, school modernization, telecommunication structures, and more.

Warranty information: Five-year parts, five-year compressor standard.

Special installation requirements: None.

Contact: Bard Mfg. Co., 419-636-1194; www.bardhvac.com.

eProduct 165

Bryant

Model: Legacy™ Series packaged rooftops (580J/558J/548J)

Footprint (in inches): Varies. Smallest size: 74 (length) by 47 (width) by 33 (height)

Serviceability features: Designed to be easy to install and maintain. Units throughout the line are similar in design for easy familiarization. Each has a large, organized control box; standardized components; conveniently centralized wiring; handled, easy-access panels; no-strip access screws; and a removable service plug to simplify taking refrigerant pressures.

Technical support: Supported by dedicated, local Bryant distributors. Bryant Solution Center available at 888-994-7237 or bryantprograms@bryant.com. Bryant Commercial Replacement Specialist Training also available.

Technical support materials: Product data and wiring diagrams; service, controls, and commissioning manuals; installation instructions; and critical parts lists available.

Noise-reduction features: Insulated cabinet and isolated scroll compressors.

IAQ equipment supported: Economizers with multiple sensor options, 2-inch filters standard on all models, multiple fan performance capabilities, and Perfect Humidity® dehumidification system.

Thermostat compatibility: Compatible with most thermostats.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: Complete offering in sizes up to 25 tons with numerous factory- and field-installed options makes it an ideal solution for the replacement market. Many models are capable of fitting on past Bryant roof curbs dating back to the late 1980s without changing utility or duct connections, saving time and money.

Warranty information: Standard commercial warranty with extended warranty programs available.

Special installation requirements: A fully packaged system. Accumulators are factory-installed on all heat pump models.

Contact: Bryant Heating and Cooling Systems, 888-994-7237; www.bryant.com.

eProduct 166

Carrier

Model: WeatherMaster® rooftop series (48HC/50HC/50HCQ)

Footprint (in inches): Varies. Smallest size: 74 (length) by 47 (width) by 33 (height)

Serviceability features: Access features include easy-grip handled access panels (optionally hinged) with easy starting, no-strip screws, and toolless filter access. The large, well-organized control box is centrally located creating convenient wiring/service points and features a new terminal board to facilitate simple safety circuit troubleshooting. Breadth of offering includes many common replacement components.

Technical support: Widespread distribution network with on-site technical advisory staff and available Commercial Replacement Experts training programs. Expert Central available at 800-946-2930 or expertcentral@carrier.com.

Technical support materials: Product data and wiring diagrams; service, controls, and commissioning manuals; installation instructions; and critical parts lists available at carrier.com or through local distributor.

Noise-reduction features: Fully insulated cabinet with belt-drive fan, scroll compressors, and rigid full-perimeter base rails.

IAQ equipment supported: Fully integrated fresh air economizer with multiple sensor options, integrated CO2 sensor, 2-inch filters (4-inch on larger sizes) and patented Humidi-Mizer® adaptive dehumidification system.

Thermostat compatibility: Compatible with most thermostats.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: Meets or exceeds Energy Star® and Consortium for Energy Efficiency (CEE) performance levels required to qualify for a variety of incentives. Simplified installation: single-point electrical and gas connections; most 3- to 10-ton models retrofit Carrier curbs back to the 1980s to eliminate need for curb adapters. Units operate in up to 125˚F ambient temperatures.

Warranty information: 15-year limited optional stainless steel heat exchanger, 10-year limited standard aluminized heat exchanger, five-year limited compressor, one-year limited all other parts with extended warranty programs available.

Special installation requirements: 3 to 12.5 ton field convertible from vertical to horizontal airflow for slab mounting; 15 to 25 ton factory-supplied vertical or horizontal airflow; single point gas and electric connections; certified and pre-engineered factory options available; pre-wired and pre-charged with refrigerant at factory; RTU open, multiple-protocol controller available.

Contact: Carrier Corp., 800-946-2930; www.carrier.com.

eProduct 167

Model: WeatherMaster packaged rooftop series (48P/50P)

Footprint (in inches): Varies. Smallest size: 257 (length) by 95 (width) by 78 (height)

Serviceability features: Access features include large, man-sized access doors; onboard diagnostics including refrigerant pressure sensors; simplified wiring connections, and plug-and-play communication options. The factory-installed DDC control system includes easy-to-use human interface that provides access to system operating parameters. Breadth of offering includes many common replacement components.

Technical support: Widespread distribution network with on-site technical advisory staff and available Commercial Replacement Experts training programs. Additional training available through Carrier University. Expert Central available at 800-946-2930 or expertcentral@carrier.com.

Technical support materials: Product data and wiring diagrams; service, controls and commissioning manuals; installation instructions; and critical parts lists available at Carrier.com or through local distributor.

Noise-reduction features: Fully insulated cabinet with isolated compressors and fans. Low sound option available factory installed.

IAQ equipment supported: Economizers with multiple sensing capabilities; high-intensity UVC lights; a variety of filter types (e.g., pleated, bag, and cartridge); capability to integrate CO2 sensors for optimum demand control ventilation logic and operation; standard insulation contains an EPA-registered, antimicrobial agent resistant to bacterial growth; double-wall construction with Sciessent® Agion® antimicrobial interior coating also available.

Thermostat compatibility: Capable of supporting common commercial thermostats; common space sensors; or building automation systems.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: Unit design allows enhanced cooling capacity matching to the building needs through extensive compressor staging capability. Control system capabilities include precise supply air temperature control for constant volume and variable air volume applications. In addition, Humidi-MiZer® adaptive dehumidification system provides control of the supply air humidity levels.

Warranty information: Three-year parts only limited on Novation® condenser coil; five-year parts only limited, nonpro-rated, on heat exchanger; one-year parts only limited all other parts.

Special installation requirements: Factory-installed pivoting outside air hoods; lifting lugs; single point gas and electric connections; certified and pre-engineered factory options available; pre-wired and pre-charged with refrigerant at factory.

Contact: Carrier Corp., 800-946-2930; www.carrier.com.

eProduct 168

Century

Model: TGCG180, TGCG240 packaged unit

Footprint (in inches): 152 (length) by 86 (width) by 57 (height)

Serviceability features: Solid state controls have diagnostic LED to assist technician. Components can be reached through front access or hinged access panels. Blower assembly slides out, and refrigerant ports are externally mounted for convenience. The large control panel has numbered and color-coded wiring.

Technical support: Technical support line available from 8 a.m. to 5 p.m. Eastern time, weekdays, at 517-787-2100.

Technical support materials: Installation, operation and maintenance manual (including wiring diagrams and troubleshooting guide) and parts list are available on website or by email.

Noise-reduction features: Entire cabinet is lined with foil-faced insulation for sound attenuation and reduced air leakage; solid-state direct spark ignition for heating and scroll compressor for cooling both contribute to quiet operation.

IAQ equipment supported: One-piece top on indoor section and sloped antibacterial drain pan provide superior water management for mold and mildew prevention. Cabinet insulation is encapsulated to minimize airborne fibers in the airstream. Includes factory-installed two-inch filters.

Thermostat compatibility: Compatible with most thermostats.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: In-shot burners and multiple inducers provide efficiency at both high and low stages. Gas heat features solid-state direct spark ignition with remote flame sensor and onboard diagnostics. Heat exchanger is tubular aluminized steel. G90 galvanized steel cabinet with powder-coat finish meets ASTMB117 Standard. Can be roof-mounted or slab-mounted.

Warranty information: Limited 10-year heat exchanger and one-year parts; some limitations apply, see printed warranty on website for details.

Special installation requirements: Comes with full perimeter base rails allowing unit to be lifted with a forklift or rigging. Unit is pre-wired for plug-in economizer. Convertible horizontal and downflow airflow for field installation flexibility.

Contact: Century Div. Heat Controller, 517-787-2100; www.century-hvac.com.

eProduct 169

ClimaCool

Model: SHC onDEMAND™ modular heat pump chiller

Footprint (in inches): 67 (length) by 34 (width) by 84 (height)

Serviceability features: Modules are fully serviceable and maintainable without removal from the modular heat pump bank or disassembly of headers. All major components such as compressors, brazed-plate heat exchangers, refrigeration components, and Pete’s ports are accessible.

Technical support: Onsite operator training upon start-up. For further information on start-up, installation, and service, call 405-745-3185 or visit www.climacoolcorp.com.

Technical support materials: Manual with installation, operation and maintenance instructions sent with every unit. Wiring diagrams are attached to the control panel’s access door. Visit www.climacoolcorp.com for technical support literature.

Noise-reduction features: Compressors installed on rubber isolators; sound attenuation panels made of 18-gauge galvanized steel with powder-coat paint finish and fiberglass insulation standard. Isolation of the chiller from the structure is possible by installing vibration-eliminating springs or pads under base rails.

IAQ equipment supported: Manufacturer did not specify.

Thermostat compatibility: Requires a special thermostat. Communicates with BAS systems.

Replacement parts compatibility: Some shared parts and some unique parts.

Additional features: The design helps save space and reduce costs while contributing to six LEED categories. Piping connections are fully configurable to same or opposite ends. Each module can be indexed for heating or cooling regardless of its position in the bank.

Warranty information: Standard one-year parts; optional four-year extended parts-only compressor.

Special installation requirements: None.

Contact: ClimaCool Corp, 407-951-5513; www.climacoolcorp.com.

eProduct 170

ClimateMaster

Model: Tranquility large water-to-water series (TMW) packaged unit

Footprint (in inches): 56 (length) by 34 (width) by 65 (height)

Serviceability features: Compressor and electrical components are all accessible from the front. All service panels are removable and have quarter-turn fasteners for quick access. The DDL controller has status LEDs and port for service tool.

Technical support: Available at 405-745-6000.

Technical support materials: All wiring diagram, installation instructions, and submittals are available online.

Noise-reduction features: All panels are heavy-gauge painted steel with a thermal and acoustic liner.

IAQ equipment supported: Manufacturer did not specify.

Thermostat compatibility: Uses DDC controller, which communicates to building automated system or hand-held monitor.

Replacement parts compatibility: Does not share replacement parts with other models.

Additional features: Offers high efficiency with advanced features and application flexibility at competitive prices. The TMW series can be used for radiant floor heating, snow/ice melt, chilled water for fan coils, hot/chilled water for make-up air, and many other types of HVAC applications. The TMW 360-600 has advanced digital controls for BAS interface, four LEDs for unit status, and compressor isolation switches. Front and back service access panels allow for side-by-side installation; the larger capacity requires fewer units per job site; staggered top water connections for ease of manifolding multiple units and DDC controls. DDC controls provide 11 safety protections for the refrigeration circuits.

Warranty information: Standard limited express coverage of 18 months from time of shipment or 12 months from start-up, whichever comes first. Optional warranties include four-year control board, four-year compressor, and four-year refrigerant.

Special installation requirements: Manufacturer did not specify.

Contact: ClimateMaster Inc., 405-745-6000; www.climatemaster.com.

eProduct 171

Coleman

Model: Outfitter™ 10 packaged unit

Footprint (in inches): 89 (length) by 59 (width) by 42 and 50 (height)

Serviceability features: Hinged, tool-free access to blower, filters, compressor, heating, and electrical sections including a slide-out blower. Variable-frequency drive (VFD) mounted on slide-out blower deck for ease of service and programming. Optional disconnect and powered or nonpowered convenience outlet, side and bottom electrical, and condensate drain connections.

Technical support: Contact distributor.

Technical support materials: Technical guides, installation manuals, and wiring diagrams located at www.upgnet.com.

Noise-reduction features: Enclosed compressor compartment and closed cell foam insulation greatly improve the sound performance of the product providing a quiet, yet well performing product.

IAQ equipment supported: Composite condensate drain pan, optional 2- or 4-inch air filters with MERV 7 or 13 ratings, and CO2 demand control ventilation. Excellent temperature and humidity control over conventional systems when equipped with the variable air volume option.

Thermostat compatibility: Compatible with most thermostats. Operates by controlling space temperature and humidity via Simplicity® Intelli-Comfort™ variable volume unit control.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: The Outfitter variable air volume system utilizes a unique control and refrigeration system to ensure responsive performance to provide cooling or heating comfort and proper air volume to independent zones when needed.

Warranty information: Five-year compressor, one-year parts and 10-year gas heat exchanger. Extended warranties are available.

Special installation requirements: Easy installation made possible with tool-free access panels, solid base rails with fork and rigging access, field convertible for bottom and side duct connections, simple operation of control system.

Contact: Johnson Controls, 414-524-4338; www.colemanhvacdealer.com.

eProduct 172

Model: Outfitter MagnaDRY™ packaged unit

Footprint (in inches): 89 (length) by 59 (width) by 42 (height)

Serviceability features: Hinged, tool-free access to blower, filters, compressor, heating, and electrical sections. Slide-out blower for easy service and adjustment. Optional disconnect and powered or non-powered convenience outlet, side and bottom electrical and condensate drain connections. Simplicity® microprocessor control board with simple, easy-to-use troubleshooting and networking options.

Technical support: Contact distributor.

Technical support materials: Technical guides, installation manuals, and wiring diagrams located at www.upgnet.com.

Noise-reduction features: Enclosed compressor compartment and closed cell foam insulation greatly improve the sound performance of the product providing a quiet, yet well performing product.

IAQ equipment supported: Composite condensate drain pan, optional 2- or 4-inch air filters with MERV 7 or 13 ratings and CO2 demand control ventilation. Precise humidity control when equipped with the MagnaDRY dehumidification option.

Thermostat compatibility: Compatible with most thermostats.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: The Outfitter MagnaDRY hot gas reheat dehumidification system utilizes a unique patented refrigeration system to ensure responsive performance and provide comfort cooling, or dehumidification when needed. Unlike other products of similar design, the MagnaDRY quickly responds to changing building space temperature or humidity.

Warranty information: Five-year compressor, one-year parts, and 10-year gas heat exchanger. Extended warranties are available.

Special installation requirements: Easy installation made possible with tool-free access panels, solid base rails with fork and rigging access, field convertible for bottom and side duct connections, simple operation of control system.

Contact: Johnson Controls, 414-524-4338; www.colemanhvacdealer.com.

eProduct 173

Comfort-Aire

Model: EKTH-2G packaged terminal heat pump

Footprint (in inches): 42 (length) by 22 (width) by 16 (height)

Serviceability features: Real-time diagnostics of onboard computer simplifies service. LED flashes error code to indicate problem; in many cases, unit will automatically clear or correct the fault condition and continue operation without interruption. Condenser shroud lifts off to facilitate inspection, cleaning, and servicing of components.

Technical support: Technical support line available from 8 a.m. to 5 p.m., Eastern time, weekdays, at 517-787-2100.

Technical support materials: Installation, operation and maintenance manual (including wiring diagrams), service manual, and parts list are available on website or by email.

Noise-reduction features: Balanced tangential blower wheel distributes air evenly with minimal operational sound. Outdoor fan has a polymer, multiblade axial airflow design that moves air quietly and efficiently. Indoor fan runs a minimum of 10 seconds before compressor starts to help reduce compressor start-up sound.

IAQ equipment supported: Two-piece lifetime filters can be accessed for cleaning and replaced without removing the shroud. Also, a molded plastic filter on the outdoor ventilation opening stops dirt and debris from entering the room air side of the unit. Closing outside vent door allows room air to be circulated and filtered.

Thermostat compatibility: Requires a special thermostat.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: The 265 V model designed for commercial applications. Automatically switches to electric heat about 40˚F outside ambient. Electric heat kW determined by power cord selection. Allows for front desk setback and in-room temperature limiting. Can be configured to a specific application through dipswitches and digital keypad, including set point limiting, front desk control, wall thermostat control, and more. Features random auto restart, anti-short cycle, in-room freeze protection, defrost protection.

Warranty information: Limited five-year compressor and one-year parts. Some limitations apply, see printed warranty on website for details.

Special installation requirements: Follow standard installation practices for packaged terminal units; units can be installed flush to the floor. Select desired electric heat (2.0 kW, 3.0 kW, or 5.0 kW) by ordering corresponding power supply kit.

Contact: Comfort-Aire Div. Heat Controller, 571-787-2100; www.comfort-aire.com.

eProduct 174

Comfortmaker

Model: CHS240 split system heat pump

Footprint (in inches): 86 (length) by 67 (width) by 50 (height)

Serviceability features: Comfort Alert® troubleshooting LED fault indicators diagnose system-related malfunctions. Newly designed terminal board facilitates simple safety circuit troubleshooting and simplified control box arrangement.

Technical support: Factory-trained Technical Service Advisors (TSAs) on staff at local distributors provide technical assistance, troubleshooting at the local level. ICP technical training is available at field schools held at participating distributor locations.

Technical support materials: Product information posted online at Comfortmaker dealer website www.gocomfortmaker.com includes product specification sheets, installation, and operation manuals.

Noise-reduction features: Units are equipped with scroll compressors and include vibration isolation for further enhancement of quiet operation. These units are equipped with suction line accumulators that smooth out refrigerant management during mild ambient conditions and the transitions during defrost operation to substantially reduce sounds associated with the scroll compressors pumping liquid refrigerant.

IAQ equipment supported: Manufacturer did not specify.

Thermostat compatibility: Compatible with most thermostats.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: All models utilize round copper tube, aluminum plate fin condenser coils (RTPF). Compressors include overload protection. All units have high pressure and loss of charge protection. Models with optional low ambient control provide cooling operation down to -20˚F.

Warranty information: Five-year limited compressor; one-year limited all other parts.

Special installation requirements: None.

Contact: International Comfort Products LLC (ICP), 800-315-4370; www.gocomfortmaker.com.

eProduct 175

Model: RGS180 packaged gas/electric rooftop

Footprint (in inches): 116 (length) by 63 (width) by 57 (height)

Serviceability features: Units have provisions for through-the-bottom power entry capability. All connections and troubleshooting points located in one convenient place, the master terminal board. Access panels have easy grip handles and no-strip screw feature. Exclusive IGC solid-state control for onboard diagnostics with LED error code designation, burner control logic and energy-saving indoor fan motor delay.

Technical support: Factory-trained Technical Service Advisors (TSAs) on staff at local distributors provide technical assistance, troubleshooting at the local level. ICP technical training is available at field schools held at participating distributor locations.

Technical support materials: Product information posted online at Comfortmaker dealer website www.gocomfortmaker.com includes product specification sheets, installation, and operation manuals.

Noise-reduction features: Quiet and efficient operation is provided by belt-driven evaporator fans.

IAQ equipment supported: Two-inch return air filters. Optional economizer control accepts CO2 sensor for IAQ capability. Accessory duct-mounted CO2 sensor available for field installation to provide outdoor air for ventilation capability on demand (DCV).

Thermostat compatibility: Compatible with most thermostats.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: ASHRAE 90.1-compliant unit is 36 percent lighter than its previous counterpart. Scroll compressor has internal line-break overload protection. Factory-installed options include three heat options (high, medium, and low), and medium and high static indoor fan option. Other options include liquid propane high altitude kits. Low-NOx models include stainless steel heat exchangers.

Warranty information: 15-year limited stainless steel heat exchanger, 10-year limited aluminized heat exchanger; five-year limited compressor; one-year limited all other parts.

Special installation requirements: Field accessory supply duct kit (CRDUCTCV002A00) required for conversion from downflow to horizontal airflow for 15-ton model.

Contact: International Comfort Products LLC (ICP), 800-315-4370; www.gocomfortmaker.com.

eProduct 176

Day and Night

Model: RGH150 packaged gas/electric rooftop

Footprint (in inches): 116 (length) by 63 (width) by 57 (height)

Serviceability features: Units feature through-the-base utility connections capability. All connections and troubleshooting points located in one convenient place, the master terminal board. Access panels have easy grip handles and no-strip screw feature. Exclusive IGC solid-state control for onboard diagnostics with LED error code designation, burner control logic and energy-saving indoor fan motor delay.

Technical support: Factory-trained Technical Service Advisors (TSAs) on staff at local distributors provide technical assistance, troubleshooting at the local level. ICP technical training is available at field schools held at participating distributor locations.

Technical support materials: Product information posted online at Day and Night dealer website www.godayandnight.com includes product specification sheets, installation, and operation manuals.

Noise-reduction features: Quiet and efficient operation is provided by belt-driven evaporator fans.

IAQ equipment supported: Two-inch return air filters. Optional economizer control accepts CO2 sensor for IAQ capability. Accessory duct-mounted CO2 sensor available for field installation to provide outdoor air for ventilation capability on demand (DCV).

Thermostat compatibility: Compatible with most thermostats.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: Energy Star qualified models are convertible from downflow to horizontal airflow. Units feature high- and low-pressure switches. Scroll compressor has internal line-break overload protection. Factory-installed options include three heat options (high, medium, and low), stainless steel heat exchangers and medium and high static indoor fan option. TXV metering devices on all models to precisely control refrigerant flow. Low-NOx models available.

Warranty information: 15-year limited stainless steel heat exchanger, 10-year limited aluminized heat exchanger; five-year limited compressor; one-year limited all other parts.

Special installation requirements: Field accessory supply duct kit (CRDUCTCV002A00) required for conversion from downflow to horizontal airflow for 12.5-ton model.

Contact: International Comfort Products LLC (ICP), 800-315-4370; www.godayandnight.com.

eProduct 177

Model: RGH240-243 packaged gas/electric rooftop

Footprint (in inches): 142 (length) by 86 (width) by 57 (height)

Serviceability features: Units have provisions for through-the-curb gas line routing. All connections and troubleshooting points located in one convenient place, the master terminal board. Access panels have easy grip handles and no-strip screw feature. Exclusive IGC solid-state control for onboard diagnostics with LED error code designation, burner control logic, and energy-saving indoor fan motor delay.

Technical support: Factory-trained Technical Service Advisors (TSAs) on staff at local distributors provide technical assistance and troubleshooting at the local level. ICP technical training is available at field schools held at participating distributor locations.

Technical support materials: Product information posted online at Day and Night dealer website www.godayandnight.com includes product specification sheets, installation, and operation manuals.

Noise-reduction features: Quiet and efficient operation is provided by belt driven evaporator fans.

IAQ equipment supported: Two-inch return air filters. Optional economizer control accepts CO2 sensor for IAQ capability. Accessory duct-mounted CO2 sensor available for field installation to provide outdoor air for ventilation capability on demand (DCV).

Thermostat compatibility: Compatible with most thermostats.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: Energy Star qualified models in dedicated vertical or horizontal airflow duct configurations. Unit features high- and low-pressure switches, freeze-protection thermostats. Scroll compressor has internal line-break overload protection. Factory-installed options include three heat options (high, medium and low), stainless steel heat exchangers, and medium and high static indoor fan option. TXV metering devices on all models to precisely control refrigerant flow.

Warranty information: 15-year limited stainless steel heat exchanger, 10-year limited aluminized heat exchanger; five-year limited compressor; one-year limited all other parts.

Special installation requirements: None.

Contact: International Comfort Products LLC (ICP), 800-315-4370; www.godayandnight.com.

eProduct 178

EarthLinked Commercial Water Heating

Model: CWH-048 and CWH-072 split system heat pump

Footprint (in inches): 17 (length) by 21 (width) by 29 (height)

Serviceability features: Unit features Adaptiv™ refrigerant flow controls, which make system charging simple, according to the company. Service valves are provided to isolate earth loops from compressor unit.

Technical support: Available from 8 a.m. to 5 p.m. Eastern time. Authorized dealers have access to after-hours phone support.

Technical support materials: Application and system selection, installation, and service manuals available on website and hard copy.

Noise-reduction features: Fully insulated cabinet, no outdoor fan.

IAQ equipment supported: Manufacturer did not specify.

Thermostat compatibility: Compatible with most thermostats.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: Direct Geoexchange uses highly conductive copper loops to transfer renewable energy from the earth, eliminating the indirect transfer medium found in water-loop geo systems.

Warranty information: Five-year compressor and refrigerant flow controls. 20-year earth loops.

Special installation requirements: Sold only through authorized, factory-trained installers.

Contact: EarthLinked Technologies, 863-701-0096; www.earthlinked.com.

eProduct 179

Fraser Johnston

Model: MagnaDRY™ packaged unit

Footprint (in inches): 89 (length) by 59 (width) by 42 (height)

Serviceability features: Hinged, tool-free access to blower, filters, compressor, heating, and electrical sections. Slide-out blower for easy service and adjustment. Optional disconnect and powered or nonpowered convenience outlet, side and bottom electrical and condensate drain connections. Simplicity® microprocessor control board with simple, easy-to-use troubleshooting and networking options.

Technical support: Contact distributor.

Technical support materials: Technical guides, installation manuals, wiring diagrams located at www.upgnet.com.

Noise-reduction features: Enclosed compressor compartment and closed cell foam insulation greatly improve the sound performance of the product providing a quiet, yet well-performing product.

IAQ equipment supported: Composite condensate drain pan, optional 2- or 4-inch air filters with MERV 7 or 13 ratings, and CO2 demand control ventilation. Precise humidity control when equipped with the MagnaDRY dehumidification option.

Thermostat compatibility: Compatible with most thermostats.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: Hot gas reheat dehumidification system utilizes a unique patented refrigeration system to ensure responsive performance and provides comfort cooling, or de-humidification when needed. Unlike other products of similar design, the MagnaDRY quickly responds to changing building space temperature or humidity.

Warranty information: Five-year compressor, one-year parts, and 10-year gas heat exchanger. Extended warranties are available.

Special installation requirements: Easy installation made possible with tool-free access panels, solid base rails with fork and rigging access, field convertible for bottom and side duct connections, simple operation of control system.

Contact: Johnson Controls, 405-419-6551; www.fraserjohnston.com.

eProduct 180

Model: Packaged Product packaged unit

Footprint (in inches): 89 (length) by 59 (width) by 42 and
50 (height)

Serviceability features: Hinged, tool-free access to blower, filters, compressor, and heating and electrical sections including a Slide-out blower. Variable-frequency drive (VFD) mounted on slide-out blower deck for ease of service and programming. Optional disconnect and powered or nonpowered convenience outlet, side and bottom electrical and condensate drain connections.

Technical support: Contact distributor.

Technical support materials: Technical guides, installation manuals, wiring diagrams located at www.upgnet.com.

Noise-reduction features: Enclosed compressor compartment and closed cell foam insulation greatly improve the sound performance of the product providing a quiet, yet well-performing product.

IAQ equipment supported: Composite condensate drain pan, optional 2- or 4-inch air filters with MERV 7 or 13 ratings, and CO2 demand control ventilation. Excellent temperature and humidity control over conventional systems when equipped with the variable air volume option.

Thermostat compatibility: Compatible with most thermostats. Operates by controlling space temperature and humidity via Simplicity® Intelli-Comfort™ variable volume unit control.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: The packaged unit’s variable air volume system utilizes a unique control and refrigeration system to ensure responsive performance to provide cooling or heating comfort and proper air volume to independent zones when needed.

Warranty information: Five-year compressor, one-year parts, and 10-year gas heat exchanger. Extended warranties are available.

Special installation requirements: Easy installation made possible with tool-free access panels, solid base rails with fork and rigging access, field convertible for bottom and side duct connections, simple operation of control system.

Contact: Johnson Controls, 405-419-6551; www.fraserjohnston.com.

eProduct 181

Fulton Heating Solutions, Inc.

Model: Vantage VTG-6000 condensing hydronic boiler

Footprint (in inches): 148 (length) by 49 (width) by 81 (height)

Serviceability features: Features access to all service-related components from the front or rear of the boiler, facilitating 1-inch side clearance between any number of units. Access to ASME stamping information is on the rear of the boiler, located under a removable access plate.

Technical support: Available 24/7 at 315-298-5121. Local service is facilitated through manufacturer’s representatives.

Technical support materials: All relevant information is available from Fulton’s engineering department.

Noise-reduction features: Manufacturer did not specify.

IAQ equipment supported: Manufacturer did not specify.

Thermostat compatibility: Compatible with most thermostats.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: Designed for ultra-high efficiency condensing applications and also features a high mass/volume heat exchanger design manufactured to be rugged, robust, and reliable.

Warranty information: Lifetime warranty against thermal shock. Additional warranties are provided for flue gas corrosion, materials and workmanship, and parts.

Special installation requirements: Installation is simple as primary, only pumping arrangements are allowed (no primary/secondary with dedicated circulator pumps are required). As with any condensing boiler, AL294C flue stack material is required, along with a condensate drain mechanism.

Contact: Fulton; www.fulton.com/index.php.

eProduct 182

Goodman

Model: CPG Commercial packaged unit

Footprint (in inches): 133 (length) by 89 (width) by 50 (height)

Serviceability features: High-capacity, steel-cased filter drier, built-in filter rack with standard 2-inch filters (convertible to 4-inch filters), bottom utility entry, 24-volt terminal strip, and contactor with lugs.

Technical support: Available from local distributors and factory direct at 888-593-9988.

Technical support materials: All materials are available from local distributors, factory direct, or they can be downloaded from www.goodmanmfg.com or PartnerLink.

Noise-reduction features: Heavy-duty, galvanized-steel cabinet, Goodman-designed sound control top, scroll compressor, efficient and quiet fan blade design.

IAQ equipment supported: Widely compatible with all commercial IAQ components and systems.

Thermostat compatibility: Compatible with most thermostats.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: Only unit with unique, TuffTube™ aluminized steel heat exchanger, R-410A refrigerant, high-efficiency scroll compressor, and exceptional warranty coverage.

Warranty information: 20-year heat exchanger limited and a five-year parts limited.

Special installation requirements: No specific installation requirements are associated with this unit.

Contact: Goodman Global Group Inc., 713-861-2500; www.goodmanmfg.com.

eProduct 183

Model: GSZ13 heat pump

Footprint (in inches): 29 (length) by 29 (width) by 34 (height)

Serviceability features: Factory-installed, biflow liquid line filter drier. Service valves with sweat connections and easy-access gauge ports. Contactor with lug connection. Ground lug connection.

Technical support: Available from local distributors and factory direct at 888-593-9988.

Technical support materials: All technical support materials are available from local distributors or they can be downloaded from the Goodman website and from PartnerLink.

Noise-reduction features: Goodman sound control top design, scroll compressor, efficient and quiet fan motor blades.

IAQ equipment supported: Supports IAQ components and systems as outlined in the technical and installation guides.

Thermostat compatibility: Compatible with most thermostats.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: The combination of R-410A refrigerant, low-pressure switch, liquid refrigerant return protection, reliable time-initiated, temperature-terminated defrost control, top and side maintenance access, and steel louver coil guard.

Warranty information: Five-year parts limited.

Special installation requirements: This unit is exceptionally easy to install.

Contact: Goodman Global Group Inc., 713-861-2500; www.goodmanmfg.com.

eProduct 184

Heil

Model: RGS180 packaged gas/electric rooftop

Footprint (in inches): 116 (length) by 63 (width) by 57 (height)

Serviceability features: Units have provisions for through-the-bottom power entry capability. All connections and troubleshooting points located in one convenient place, the master terminal board. Access panels have easy grip handles and no-strip screw feature. Exclusive IGC solid-state control for onboard diagnostics with LED error code designation, burner control logic, and energy-saving indoor fan motor delay.

Technical support: Factory-trained Technical Service Advisors (TSAs) on staff at local distributors provide technical assistance, troubleshooting at the local level. ICP technical training is available at field schools held at participating distributor locations.

Technical support materials: Product information posted online at Heil dealer website www.goheil.com includes product specification sheets, installation, and operation manuals.

Noise-reduction features: Quiet and efficient operation is provided by belt-driven evaporator fans.

IAQ equipment supported: Two-inch return air filters. Optional economizer control accepts CO2 sensor for IAQ capability. Accessory duct-mounted CO2 sensor available for field installation to provide outdoor air for ventilation capability on demand (DCV).

Thermostat compatibility: Compatible with most thermostats.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: ASHRAE 90.1-compliant unit is 36 percent lighter than its previous counterpart. Scroll compressor has internal line-break overload protection. Factory-installed options include three heat options (high, medium, and low), and medium and high static indoor fan option. Other options include liquid propane / high altitude kits. Low NOx models include stainless steel heat exchangers.

Warranty information: 15-year limited stainless steel heat exchanger, 10-year limited aluminized heat exchanger; five-year limited compressor; one-year limited all other parts.

Special installation requirements: Field accessory supply duct kit (CRDUCTCV002A00) required for conversion from downflow to horizontal airflow for 15-ton model.

Contact: International Comfort Products LLC (ICP), 800-315-4370; www.goheil.com.

eProduct 185

Model: RHS181-183 packaged heat pump

Footprint (in inches): 128 (length) by 86 (width) by 49 (height)

Serviceability features: Units have provisions for through-the-bottom power entry capability. All connections and troubleshooting points located in one convenient place, the master terminal board. Access panels have easy grip handles and no-strip screw feature. Large laminated control wiring and power wiring drawings are affixed to unit to make troubleshooting easy.

Technical support: Factory-trained Technical Service Advisors (TSAs) on staff at local distributors provide technical
assistance, troubleshooting at the local level. ICP technical training is available at field schools held at participating distributor locations.

Technical support materials: Product information posted online at Heil dealer website www.goheil.com includes product specification sheets, installation and operation manuals.

Noise-reduction features: Quiet and efficient operation is provided by belt-driven evaporator fans.

IAQ equipment supported: Two-inch return air filters. Optional economizer control accepts CO2 sensor for IAQ capability. Accessory duct-mounted CO2 sensor available for field installation to provide outdoor air for ventilation capability on demand (DCV).

Thermostat compatibility: Compatible with most thermostats.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: Dedicated vertical or horizontal airflow duct configuration models. ASHRAE 90.1-compliant unit features loss-of-charge, freeze-protection, and high-pressure switches. Scroll compressor has internal line-break overload protection. Factory-installed options available, including medium and high static indoor fan option.

Warranty information: Five-year limited compressor; one-year limited all other parts.

Special installation requirements: None.

Contact: International Comfort Products LLC (ICP), 800-315-4370; www.goheil.com.

eProduct 186

Hydrotherm

Model: KN-30 Series boilers

Footprint (in inches): 81 (length) by 31 (width) by 72 (height)

Serviceability features: Easy access igniter, controls, air filter, and controls located at front of the boiler. Simple burner access through top.

Technical support: Multiple training programs located in Westfield, Mass., Boyertown, Pa., and Mississauga, Ontario. Direct factory support available Monday to Friday from 8 a.m. to 5 p.m.

Technical support materials: Visit www.hydrothermkn.com for the latest news, support, and literature requirements.

Noise-reduction features: Manufacturer did not specify.

IAQ equipment supported: Manufacturer did not specify.

Thermostat compatibility: Compatible with most thermostats.

Replacement parts compatibility: Some shared parts and some unique parts.

Additional features: Manufacturer did not specify.

Warranty information: Manufacturer did not specify.

Special installation requirements: Manufacturer did not specify.

Contact: Hydrotherm, 413-564-5515; www.hydrothermkn.com.

eProduct 187

ICP Commercial

Model: RGH150 packaged gas/electric rooftop

Footprint (in inches): 116 (length) by 63 (width) by 57 (height)

Serviceability features: Units feature through-the-base utility connections capability. All connections and troubleshooting points located in one convenient place, the master terminal board. Access panels have easy grip handles and no-strip screw feature. Exclusive IGC solid-state control for onboard diagnostics with LED error code designation, burner control logic, and energy saving indoor fan motor delay.

Technical support: Factory-trained Technical Service Advisors (TSAs) on staff at local distributors provide technical assistance, troubleshooting at the local level. ICP technical training is available at field schools held at participating distributor locations.

Technical support materials: Product information posted online at ICP Commercial dealer website www.goicpcommercial.com includes product specification sheets, installation and operation manuals.

Noise-reduction features: Quiet and efficient operation is provided by belt-driven evaporator fans.

IAQ equipment supported: Two-inch return air filters. Optional economizer control accepts CO2 sensor for IAQ capability. Accessory duct-mounted CO2 sensor available for field installation to provide outdoor air for ventilation capability on demand (DCV).

Thermostat compatibility: Compatible with most thermostats.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: Energy Star-qualified models are convertible from downflow to horizontal airflow. Units feature high- and low-pressure switches. Scroll compressor has internal line-break overload protection. Factory-installed options include three heat options (high, medium, and low), stainless steel heat exchangers and medium and high static indoor fan option. TXV metering devices on all models to precisely control refrigerant flow. Low NOx models available.

Warranty information: 15-year limited stainless steel heat exchanger, 10-year limited aluminized heat exchanger; five-year limited compressor; one-year limited all other parts.

Special installation requirements: Field accessory supply duct kit (CRDUCTCV002A00) required for conversion from downflow to horizontal airflow for 12.5-ton model.

Contact: International Comfort Products, LLC (ICP), 800-315-4370; www.goicpcommercial.com.

eProduct 188

Model: RGH300-303 packaged gas/electric rooftop

Footprint (in inches): 158 (length) by 86 (width) by 57 (height)

Serviceability features: Units have provisions for through-the-curb gas line routing. All connections and troubleshooting points located in one convenient place, the master terminal board. Access panels have easy grip handles and no-strip screw feature. Exclusive IGC solid-state control for onboard diagnostics with LED error code designation, burner control logic, and energy saving indoor fan motor delay.

Technical support: Factory-trained Technical Service Advisors (TSAs) on staff at local distributors provide technical assistance, troubleshooting at the local level. ICP technical training is available at field schools held at participating distributor locations.

Technical support materials: Product information posted on-
line at ICP Commercial dealer website www.goicpcommercial.com includes product specification sheets, installation and operation manuals.

Noise-reduction features: Quiet and efficient operation is provided by belt driven evaporator fans.

IAQ equipment supported: Two-inch return air filters. Optional economizer control accepts CO2 sensor for IAQ capability. Accessory duct-mounted CO2 sensor available for field installation to provide outdoor air for ventilation capability on demand (DCV).

Thermostat compatibility: Compatible with most thermostats.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: Energy Star-qualified models in dedicated vertical or horizontal airflow duct configurations. Unit features high- and low-pressure switches, freeze-protection thermostats. Scroll compressor has internal line-break overload protection. Factory-installed options include three heat options (high, medium, and low), stainless steel heat exchangers and medium and high static indoor fan option. TXV metering devices on all models to precisely control refrigerant flow.

Warranty information: 15-year limited stainless steel heat exchanger, 10-year limited aluminized heat exchanger; five-year limited compressor; one-year limited all other parts.

Special installation requirements: None.

Contact: International Comfort Products LLC (ICP), 800-315-4370; www.goicpcommercial.com.

eProduct 189

Johnson Controls (JCI)

Model: Series 10™ MagnaDRY packaged unit

Footprint (in inches): 89 (length) by 59 (width) by 42 (height)

Serviceability features: Hinged, tool-free access to blower, filters, compressor, heating, and electrical sections. Slide-out blower for easy service and adjustment. Optional disconnect and powered or nonpowered convenience outlet, side and bottom electrical and condensate drain connections. Simplicity® microprocessor control board with simple, easy-to-use troubleshooting and networking options.

Technical support: Contact distributor.

Technical support materials: Technical guides, installation manuals, wiring diagrams located at www.johnsoncontrols.com.

Noise-reduction features: Enclosed compressor compartment and closed cell foam insulation greatly improve the sound performance of the product providing a quiet, yet well-performing product.

IAQ equipment supported: Composite condensate drain pan, optional 2- or 4-inch air filters with MERV 7 or 13 ratings, and CO2 demand control ventilation. Precise humidity control when equipped with the MagnaDRY dehumidification option.

Thermostat compatibility: Compatible with most thermostats.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: The hot gas reheat dehumidification system utilizes a unique patented refrigeration system to ensure responsive performance and provides comfort cooling, or dehumidification when needed. Unlike other products of similar design, the MagnaDRY quickly responds to changing building space temperature or humidity.

Warranty information: Five-year compressor, one-year parts, and 10-year gas heat exchanger. Extended warranties are available.

Special installation requirements: Easy installation made possible with tool-free access panels, solid base rails with fork and rigging access, field convertible for bottom and side duct connections, simple operation of control system.

Contact: Johnson Controls, 414-524-5487; www.johnsoncontrols.com.

eProduct 190

Model: Series 10™ packaged unit

Footprint (in inches): 89 (length) by 59 (width) by 42 and
50 (height)

Serviceability features: Hinged, tool-free access to blower, filters, compressor, heating, and electrical sections including a slide-out blower. Variable frequency-drive (VFD) mounted on slide-out blower deck for ease of service and programming. Optional disconnect and powered or nonpowered convenience outlet, side and bottom electrical and condensate drain connections.

Technical support: Contact distributor.

Technical support materials: Technical guides, installation manuals, wiring diagrams located at www.johnsoncontrols.com.

Noise-reduction features: Enclosed compressor compartment and closed cell foam insulation greatly improve the sound performance of the product providing a quiet, yet well-performing product.

IAQ equipment supported: Composite condensate drain pan, optional 2- or 4-inch air filters with MERV 7 or 13 ratings, and CO2 demand control ventilation. Excellent temperature and humidity control over conventional systems when equipped with the variable air volume option.

Thermostat compatibility: Compatible with most thermostats. Operates by controlling space temperature and humidity via Simplicity® Intelli-Comfort™ variable volume unit control.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: The variable air volume system utilizes a unique control and refrigeration system to ensure responsive performance to provide cooling or heating comfort and proper air volume to independent zones when needed.

Warranty information: Five-year compressor, one-year parts, and 10-year gas heat exchanger. Extended warranties are available.

Special installation requirements: Easy installation made possible with tool-free access panels, solid base rails with fork and rigging access, field convertible for bottom and side duct connections, simple operation of control system.

Contact: Johnson Controls, 414-524-5487; www.johnsoncontrols.com.

eProduct 191

Laars

Model: NeoTherm boiler and volume water heater

Footprint (in inches): Manufacturer did not specify.

Serviceability features: Easily removable front panel gives access to heat exchanger and other components while control remains accessible on upper bezel to aid with diagnostics.

Technical support: Available at 800-900-9276, from 8 a.m. to 5 p.m. Eastern time.

Technical support materials: Installation manuals with parts listing and wiring diagrams come with each boiler SEEK approved Revit files available online at www.laars.com.

Noise-reduction features: Manufacturer did not specify.

IAQ equipment supported: Very low 10-ppm NOx emissions.

Thermostat compatibility: Compatible with most thermostats.

Replacement parts compatibility: Some shared parts and some unique parts.

Additional features: This fully packaged, 95 percent efficient condensing hydronic boiler or volume water heater with 5-to-1 turndown available in sizes from 285 to 1000 MBtuh. Zero clearance to combustibles and convenient top connections (horizontal or vertical direct vent) make it an excellent choice for tight installations.

Warranty information: 10-year limited (visit www.laars.com for details).

Special installation requirements: Can lead-lag (daisy chain) up to eight NeoTherm boilers or volume water heaters and control the system via the onboard Laars Integrated Control System built into each NeoTherm. Integrates with building automation systems and communicates via Modbus.

Contact: Laars Heating Systems, 603-335-6300; www.laars.com.

eProduct 192

Lennox Industries

Model: EL195E gas furnace

Footprint (in inches): 29 (length) by 18 to 25 (depending on model) (width) by 33 (height)

Serviceability features: Tool-free latches on blower and burner doors, gas piping and electrical service inlets on both cabinet sides, a safety interlock switch that automatically shuts off power to the unit when the blower compartment access door is removed and a removable blower and burner assembly allows for quick, easy servicing.

Technical support: Technical documents available at www.lennoxcommercial.com or by calling 877-726-0024.

Technical support materials: Engineering handbook, installation and operation manual, and service manual available online.

Noise-reduction features: A fully insulated cabinet with foil-faced insulation on the sides and back of the heating compartment ensures quiet, efficient operation. Plus, a secondary heat exchanger allows the furnace to achieve high efficiency levels by capturing additional heat.

IAQ equipment supported: The low-speed fan slowly circulates a consistent, continuous flow of air. It also increases the effectiveness of the system’s filters, allowing them to capture and remove more pollutants from indoor air. Lennox’s add-on indoor coils, high-efficiency air cleaners, and humidifiers can easily be integrated for enhanced air quality.

Thermostat compatibility: Compatible with most thermostats.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: Power Saver technology utilizes a constant torque motor to increase system efficiency through quiet and continual operation. A low-profile cabinet allows upflow or horizontal installation. A patented ArmorTuf™ aluminized steel Duralok Plus® heat exchanger, Lennox burner box design, SureLight® igniter, and control board offer long product life and reliability, according to the company.

Warranty information: 10-year warranty Duralok Plus aluminized steel heat exchanger in nonresidential applications. All other cover components are covered by five-year in nonresidential applications.

Special installation requirements: In the U.S., flue sizing must conform to the methods outlined in the current National Fuel Gas Code (NFPA 54/ANSI−Z223.1) or applicable provisions of local building codes. In Canada flue sizing must conform to the methods outlined in National Standard of Canada CAN/CSA−B149.1.

Contact: Lennox Industries, 877-726-0024; www.lennoxcommercial.com.

eProduct 193

LG Electronics USA

Model: Multi V Water II Heat Recovery (ARWB072BA2, ARWB144BA2, ARWB096DA2, ARWB192DA2) water-cooled variable refrigerant flow heat pump

Footprint (in inches): 22 (length) by 31 (width) by 44 (height)

Serviceability features: Pipe connections and service panels are front accessible. Removal for front access panel allows easy access to compressors and controls.

Technical support: Available at 888-865-3026.

Technical support materials: Submittals, service manuals, and installation manuals are immediately available to contractors. LG also has computerized system design software (LATS), which provides diagrams for refrigerant pipe layouts and equipment selection.

Noise-reduction features: Inverter scroll compressor reduces sound levels.

IAQ equipment supported: IAQ features are not applicable for this product as it provides heating (or cooling) to indoor units.

Thermostat compatibility: Requires a special thermostat.

Replacement parts compatibility: Some shared parts and some unique parts.

Additional features: The product is designed to provide the benefits of VRF such as lower operational costs, minimal ductwork, and zoning while offering geothermal capabilities. Compact size allows installation in smaller mechanical rooms, giving back floor space. The front pipe connections allow units to be stacked with an independent racking system.

Warranty information: Two-year operational parts and six-year refrigerant system parts.

Special installation requirements: Units connect to Multi V indoor units, which have factory-installed electronic expansion valves. LG provides Y-branch connectors, headers, and heat recovery units, which can reduce the labor and material cost of refrigerant pipe installation.

Contact: LG Electronics USA, 312-397-6064; www.lg-vrf.com.

eProduct 194

Lochinvar

Model: CREST® condensing boiler (FBN1500-3500)

Footprint (in inches): 83 (length) by 41 (width) by 80 (height)

Serviceability features: Features the Smart Touch™ operating control enhanced with an 8-inch touchscreen display; this advanced control offers ease of setup and use by installing contractors and includes Modbus protocol for easy integration into BMS. Featuring a sleek, smart design, CREST offers distinctive features and control parameters to provide facility managers with functionality, ease-of-operation, and data retrieval.

Technical support: Available at 800-722-2101, from 8 a.m. to 5 p.m. Central time.

Technical support materials: Wiring diagrams, piping diagrams, literature, installation and operation manual, service manual, user manual, pump recommendations, replacement parts list, product summary, warranty information, plan view drawings, typical spec, technical service, etc., are available at www.lochinvar.com

Noise-reduction features: No special sound reduction measures are required. The boiler is library quiet, according to the company.

IAQ equipment supported: Manufacturer did not specify.

Thermostat compatibility: The Smart Touch control is a dedicated circuit board that among many other functions, acts as the thermostat.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: CREST brings leading-edge technology and exceptional energy efficiency to the largest commercial applications, making it ideal for both new construction and energy retrofit applications. Available in five models from 1.5 to 3.5 million Btuh, CREST offers thermal efficiencies as high as 99 percent. Designed with innovative fire-tube technology integrated with the exclusive Smart Touch control, CREST offers greater design flexibility and distinctive performance characteristics to meet today’s building standards, according to the company.

Warranty information: 10-year limited, which covers heat exchanger for leakage, thermal shock or other malfunction caused by defects in materials and/or workmanship. It extends to the first owner as long as the boiler remains installed at its original place of installation.

Special installation requirements: Smart Touch control offers ease of installation and data retrieval. CREST includes Modbus protocol for easy integration into BMS. Venting flexibility allows both vertical and horizontal venting options with increased vent lengths and configurations.

Contact: Lochinvar Corp., 615-889-8900; www.Lochinvar.com.

eProduct 195

Luxaire

Model: Ovation™ 10 packaged unit

Footprint (in inches): 89 (length) by 59 (width) by 42 and 50 (height)

Serviceability features: Hinged, tool-free access to blower, filters, compressor, heating, and electrical sections including a slide-out blower. Variable-frequency drive (VFD) mounted on slide-out blower deck for ease of service and programming. Optional disconnect and powered or nonpowered convenience outlet, side and bottom electrical and condensate drain connections.

Technical support: Contact distributor.

Technical support materials: Technical guides, installation manuals, wiring diagrams located at www.upgnet.com.

Noise-reduction features: Enclosed compressor compartment and closed cell foam insulation greatly improve the sound performance of the product providing a quiet, yet well-performing product.

IAQ equipment supported: Composite condensate drain pan, optional 2- or 4-inch air filters with MERV 7 or 13 ratings, and CO2 demand control ventilation. Excellent temperature and humidity control over conventional systems when equipped with the variable air volume option.

Thermostat compatibility: Compatible with most thermostats. Operates by controlling space temperature and humidity via Simplicity® Intelli-Comfort™ variable volume unit control.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: System utilizes a unique control and refrigeration system to ensure responsive performance to provide cooling or heating comfort and proper air volume to independent zones when needed.

Warranty information: Five-year compressor, one-year parts, and 10-year gas heat exchanger. Extended warranties are available.

Special installation requirements: Easy installation made possible with tool-free access panels; solid base rails with fork and rigging access; field convertible for bottom and side duct connections; simple operation of control system.

Contact: Johnson Controls, 414-524-4338; www.joinluxaire.com.

eProduct 196

Model: Ovation MagnaDRY packaged unit

Footprint (in inches): 89 (length) by 59 (width) by 42 (height)

Serviceability features: Hinged, tool-free access to blower, filters, compressor, heating, and electrical sections. Slide-out blower for easy service and adjustment. Optional disconnect and powered or nonpowered convenience outlet, side and bottom electrical and condensate drain connections. Simplicity® microprocessor control board with simple, easy-to-use troubleshooting and networking options.

Technical support: Contact distributor.

Technical support materials: Technical guides, installation manuals, wiring diagrams located at www.upgnet.com.

Noise-reduction features: Enclosed compressor compartment and closed cell foam insulation greatly improve the sound performance of the product providing a quiet, yet well performing product.

IAQ equipment supported: Composite condensate drain pan, optional 2- or 4-inch air filters with MERV 7 or 13 ratings and CO2 demand control ventilation. Precise humidity control when equipped with the MagnaDRY dehumidification option.

Thermostat compatibility: Compatible with most thermostats.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: Hot gas reheat dehumidification system utilizes a unique patented refrigeration system to ensure responsive performance and provides comfort cooling, or dehumidification when needed. Unlike other products of similar design, the MagnaDRY quickly responds to changing building space temperature or humidity.

Warranty information: Five-year compressor, one-year parts, and 10-year gas heat exchanger. Extended warranties are available.

Special installation requirements: Easy installation made possible with tool-free access panels, solid base rails with fork and rigging access, field convertible for bottom and side duct connections, simple operation of control system.

Contact: Johnson Controls, 414-524-4338; www.joinluxaire.com.

eProduct 197

MACH

Model: C4000 condensing boiler

Footprint (in inches): 67 (length) by 32 (width) by 79 (height)

Serviceability features: Condensing boilers are easily serviced in the field. The unique ENVI® control provides error messages in plain text as well as codes for easy troubleshooting. Quick turn fasteners allow fast access to boiler internals.

Technical support: Available through factory-authorized representatives. Call 877-728-5351 from 8 a.m. to 5 p.m. Eastern time for the closest representative.

Technical support materials: REVIT and CAD drawings are available through the website www.harscopk.com. Technical support and information are also available through factory-authorized manufacturers’ representatives.

Noise-reduction features: Boilers have been tested at less than 70 db.

IAQ equipment supported: Manufacturer did not specify.

Thermostat compatibility: Compatible with most thermostats.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: Provides 4 million Btuh but is small enough to fit through a standard doorway. It is also shallow enough to easily go through hallways and around corners. The CSA certified 95 percent efficiency helps qualify for federal, state, and local energy and utility rebates.

Warranty information: Five-year heat exchanger and burner, 10-year warranty against failure due to thermal shock from the date of shipment (the warranty period).

Special installation requirements: Manufacturer did not specify.

Contact: Harsco Industrial Patterson-Kelley, 570-421-7500; www.harscopk.com.

eProduct 198

Mammoth

Model: R6GP packaged gas/electric unit

Footprint (in inches): 101 (length) by 57 (width) by 43 or 55 (height)

Serviceability features: High- and low-pressure controls and high/low service ports allow quick access without disrupting operation. 75-vA transformer includes 4-amp circuit breaker to protect the low-voltage circuit. Liquid line filter driers. Crankcase heater provides protection from liquid floodback. Freeze protection thermostats provide reliable compressor operation. Direct spark ignition control with 3-amp fuse, flame sensing, and diagnostic LED.

Technical support: Available at 800-422-4328, Monday-Friday, 8 a.m. to 4:30 p.m. Central time. Literature available at www.nordyne.com.

Technical support materials: Wiring diagrams, replacement parts lists, installation instructions.

Noise-reduction features: Fully insulated bottom pan.

IAQ equipment supported: High efficient blower motor meets the requirements of NEMA 12/19/2010

Thermostat compatibility: Compatible with most thermostats.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: All units are 100 percent fired and tested on the manufacturing line.

Warranty information: One-year all parts, five-year compressor, and 10-year heat exchanger.

Special installation requirements: Manufacturer did not specify.

Contact: Nordyne, 636-561-7300; www.nordyne.com.

eProduct 199

Marvair

Model: GeoScholar III VWISA packaged water-source heat pump

Footprint (in inches): 48 (length) by 30 (width) by 83 (height)

Serviceability features: Double doors in the front provide easy access to all filters, parts, and controls. No need to slide unit from wall for service. The indoor coils are easily accessible for cleaning.

Technical support: Available 24/7 at 800-841-7854, ext. 146 or ext. 113, during normal working hours. For after hours and weekend service, call service pager at 800-204-8210.

Technical support materials: Engineering design manual, wiring diagrams, installation manual, exploded views and parts lists, service and maintenance manual. All literature can be downloaded from website. Service schools are periodically held at the factory and at customers’ premises.

Noise-reduction features: Double-wall panels with 1 ¼-inch insulation between the two panels, perforated interior panel, and insulation function as an array of Helmholtz resonators, low vibration scroll compressor wrapped in a sound-absorbing jacket, electronically commutated indoor air motor ensures constant airflow.

IAQ equipment supported: Designed to bring up to 450 cfm into the classroom. GreenWheel® ERV, GreenCube™ ERV, and motorized dampers offer a wide variety of fresh air options. For humidity control, modulating hot gas reheat is available. MERV 6 filters are standard with optional MERV 13.

Thermostat compatibility: Compatible with most thermostats.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: The GeoScholar III was designed from the onset for unsurpassed quiet operation and high efficiency. With the proper installation, sound levels of 45 dBA or less in a free blow can be obtained. Humidity control with two-stage compressors. Water source allows increased efficiency over wide range of ambient conditions

Warranty information: One-year parts, five-year compressor.

Special installation requirements: Complete installation manuals available.

Contact: Marvair, 229-273-3636; www.marvair.com.

eProduct 200

McQuay

Model: Maverick II MPS015F-050F packaged rooftop

Footprint (in inches): 185 to 273 (length) by 74 to 97 (width) by 54 to 63 (height)

Serviceability features: Units arrive as a complete package, including fully tested controls. This eliminates expensive field assembly and control installation. Hinged doors on both sides of the unit provide easy access for maintenance and service personnel that promotes routine maintenance and reduces service costs. MicroTech III controls provide easy equipment diagnostics and adjustments at the controller. Open Choices feature provides interoperability with building automation systems (BAS), including BACnet and LonTalk protocols.

Technical support: Contact local McQuay Representative, or go to www.mcquay.com.

Technical support materials: Installation manual, operator manual, brochure, video, installation diagrams, electrical diagrams. Mechanical design engineers can incorporate equipment into the building mechanical system design with BIM modeling.

Noise-reduction features: Spring-isolated supply fans reduce mechanical vibration. Double-bladed airfoil fan reduces sound power in the 63- to 250-Hz octave bands.

IAQ equipment supported: Double-wall construction, stainless steel double-sloped drain pan, modulating outdoor air damper, two-stage filtration. Dehumidification control with modulating hot gas reheat, with a 20˚F temperature rise.

Thermostat compatibility: Space sensor for DDC control.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: The energy recovery wheel is fully integrated into the design allowing for single-point power connection and unitary rigging. Temperature controls for the energy recovery wheel are fully integrated into the unit’s DDC controller.

Warranty information: One-year parts, optional five-year parts.

Special installation requirements: Unit DDC controller has default set points for easy unit commissioning. Manual control mode allows for quick unit start-up.

Contact: McQuay International, 763-553-5330; www.mcquay.com.

eProduct 201

Mitsubishi Electric Cooling and Heating

Model: Mitsubishi Electric H2i® Y-Series (PUHY-HP72T JMU-A) split system

Footprint (in inches): 30 (length) by 36 (width) by 65 (height)

Serviceability features: Built-in self-diagnostics direct a technician to a specific issue. Convenient front, side, and top panels allow for easy access to serviceable components. Easily accessible filters, no ductwork to keep clean, and simple wiring result in minimal maintenance, according to the company.

Technical support: Available at 877-391-5550 from 8 a.m. to 7 p.m. Eastern time.

Technical support materials: Diagrams, troubleshooting FAQs, installation instructions, submittals, and spec sheets available at www.mehvac.com.

Noise-reduction features: Manufacturer did not specify.

IAQ equipment supported: The indoor units use a sophisticated multi-part filter system to remove contaminants like allergens, viruses, and bacteria from the air. A hybrid catechin-pre-filter system absorbs odor-causing gases. A Blue-enzyme anti-allergen filter reduces germs and traps particles. Some units have the Platinum Catalyst Deodorizing filter that uses nanotechnology for high-power odor absorption.

Thermostat compatibility: Requires a special thermostat.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: The exclusive Hyper-Heating (H2i®) allows the system to deliver 100 percent capacity at 0°F and 84 percent heating capacity at -13˚F. H2i uses flash technology, which recollects energy that is normally wasted in the flash process at the outdoor coil.

Warranty information: Seven-year compressor, one-year parts.

Special installation requirements: Manufacturer did not specify.

Contact: Mitsubishi Electric Cooling and Heating, 678-376-2900; www.mitsubishipro.com.

eProduct 202

Modine

Model: Atherion packaged rooftop ventilation system

Footprint (in inches): 111 (length) by 102 (width) by 71 (height)

Serviceability features: Slide-out blower and pivoting assembly with auto tensioner for replacement or maintenance; optional ERV featuring a 4a Zeolite-coated aluminum wheel that slides out for cleaning, along with a removable motor panel.

Technical support: A start-up option from a factory service engineer is available upon purchase.

Technical support materials: Sales brochures and technical information are now available online at www.modinehvac.com/rooftopventilation.

Noise-reduction features: Two-inch double-wall construction; efficient low-noise condenser fans; airfoil plenum fans used in the main unit and the ERV.

IAQ equipment supported: Features best-in-class MERV 16 filtration along with MERV 10 pre-filters. The optional ERV includes MERV 10 fresh and/or exhaust air filters.

Thermostat compatibility: Manufacturer did not specify.

Replacement parts compatibility: Manufacturer did not specify.

Additional features: Stands above the competition with its best-in-class, proprietary, MERV 16 filters with the lowest air-side pressure drop on the market; optional high-efficiency gas heating option (Conservicore technology); proven PF microchannel condenser coil technology for reduced depth, lower air-side pressure, and improved corrosion resistance; meets ASHRAE 90.1 and 189 standards.

Warranty information: Standard two-year parts; five-year gas heat exchanger; and two-year compressor

Special installation requirements: None.

Contact: Modine Mfg. Co., 800-828-4328 (800-828-HEAT); www.modinehvac.com.

eProduct 203

Peerless Boilers

Model: Series TCII™ packaged steam or hot water boiler

Footprint (in inches): 63 to 199 (length) by 37 (width) by 63 (height)

Serviceability features: Easy access to sections by removal of jacket, clean-out plates and canopy, combustion chamber access is through burner plate, common controls are used to aid in familiarity and ease of troubleshooting.

Technical support: Visit www.peerlessboilers.com for representative and technical assistance.

Technical support materials: Visit peerlessboilers.com to download materials available to contractors: full service and installation manuals, venting, piping, and wiring diagrams, boiler room layouts, troubleshooting guide, PowerPoint training, illustrated parts guide, and hands-on technical training in the field and at training facility in Boyertown, Pa.

Noise-reduction features: Heavy insulation and burner covers aid in decreasing operational noises.

IAQ equipment supported: Low NOx operation with burners specifically designed to release less pollutants into the atmosphere.

Thermostat compatibility: T-stats, boiler controls, and building management systems are available for use with this boiler system.

Replacement parts compatibility: Some shared parts and some unique parts.

Additional features: Designed for higher efficiencies and assembled with graphite port connectors to ease installation and protect against potentially harmful lubricants. Low NOx burner applications, integral damper with cast iron flue connector, and balance return temperature system to ease concerns of near boiler piping and prevent potentially damaging temperature differentials in the boiler sections.

Warranty information: One-year parts, 10-year boiler sections. Extended five-year program is available.

Special installation requirements: Requires knowledge of combustion equipment, proper venting techniques, and piping.

Contact: PB Heat LLC/Peerless Boilers, 610-845-6130; www.peerlessboilers.com.

eProduct 204

Model: PureFire® PF-850 and 1000 packaged boiler units

Footprint (in inches): 27 (length) by 36 to 39 (width) by 45 (height)

Serviceability features: Self-diagnostics, complete access to all components, integral condensate neutralization unit, all communication in easy-to-understand English, quick access to combustion chamber, test mode to assist on start-up and troubleshooting, dual flame sensing, and boilers can be stacked to minimize service area.

Technical support: Available at www.peerlessboilers.com for representative and technical assistance.

Technical support materials: Visit peerlessboilers.com to download materials available to contractors: full service and installation manuals, venting, piping and wiring diagrams, boiler room layouts, troubleshooting guide, PowerPoint training, illustrated parts guide, and hands-on technical training in the field and at training facility in Boyertown, Pa.

Noise-reduction features: Sealed cabinet allows for quiet operation.

IAQ equipment supported: Low NOx for green operation.

Thermostat compatibility: Works with thermostats or building automation systems.

Replacement parts compatibility: Some shared parts and some unique parts.

Additional features: Unique condensate system; ability to common vent and cascade boilers — up to 16 units in a multiple boiler application; ability to stack boilers; and a feature-rich control that is easy to set-up, troubleshoot, and operate. Most thoroughly tested high-efficiency boiler series in the world.

Warranty information: One-year parts and labor with all registered PureFire boilers. Standard one-year parts and 10-year heat exchanger. Five- and 10-year extended plans available.

Special installation requirements: Requires knowledge of combustion equipment, proper venting techniques, and piping.

Contact: PB Heat LLC, 610-845-6130; www.peerlessboilers.com.

eProduct 205

Reznor

Model: RDCC packaged heating/cooling/ventilating unit

Footprint (in inches): 76 to 240 (length) by 42 to 101 (width) by 44 to 86 (height)

Serviceability features: Easy access to all cabinets with wide hinged doors. An IQ Controls System was specifically designed to meet the demanding needs of make-up air applications. Controls have native BACnet and Lon communications. Test and diagnostic routines are included for easy service and start-up.

Technical support: Factory startup assistance is available (must be specified at the time of the order). For more information call 855-862-4822. Service questions can be directed to the local Reznor sales engineer at 800-695-1901, ext. 1.

Technical support materials: All support materials are shipped with the equipment, but parts manuals and installation and maintenance manuals are available on the Reznor website. Wiring diagrams are also available and can be easily looked up by serial number.

Noise-reduction features: While units installed outdoors don’t typically require sound attenuation, the horizontal discharge roof curb options include insulation to help maintain temperature and deaden the sound level.

IAQ equipment supported: New standards (90.1-2010, 62.1-2010, 189-2007) and standards that will be adopted in the future will require increased outdoor ventilation for improved IAQ. Model RDCC is capable of efficiently heating or cooling 100 percent outdoor air. A similar unit, Model RDDC, is capable of dehumidification of outside air. Other IAQ features include optional MERV 13 filters and an integrated energy recovery module.

Thermostat compatibility: Compatible with most thermostats. Requires a special thermostat. Special controls maximize unit performance.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: Model RDCC is equipped with deep modulation equipment that operates at a minimum of 80 percent fuel efficiency. As the unit modulates through the 8:1 range, it actually becomes more fuel efficient at lower ratios. The unit can provide 100˚F temperature rise with a turndown as low as 12 percent.

Warranty information: Standard 12 month. Optional extended warranties are available for up to five years on compressors, and 10 years on heat exchanger. Optional one-year labor warranty is also available.

Special installation requirements: No special requirements needed for installation.

Contact: Reznor/Thomas and Betts, 800-695-1901; www.RezSpec.com.

eProduct 206

Rheem

Model: Value Line (RKKL) packaged gas/electric unit

Footprint (in inches): 82 to 124 (length) by 48 to 59 (width) by 35 to 57 (height)

Serviceability features: Easy-access panels for the line. Contractors can access the compressor, control box, etc., by removing service panels on the units. The units are equipped with external gauge ports which enable the compressor service panel to stay in place while the unit is running.

Technical support: Available at 479-648-6237, Monday to Friday, from 8 a.m. to 5 p.m., Central time.

Technical support materials: Spec sheets, wiring diagrams, service/troubleshooting information, installation instructions, and information on parts and part numbers.

Noise-reduction features: Outdoor fans discharge upwards; compressor isolation grommets; insulated panels; and balanced blower wheels and fan blades.

IAQ equipment supported: Two-inch disposable filters included as standard features; insulation with no raw edge exposed; excellent latent to sensible capacity ratios; and a sloped, slide-out cleanable drain pan.

Thermostat compatibility: Compatible with most thermostats.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: The RKKL line leads the industry in unit weight, size, and capacity. The line also leads the industry in airflow and R-410 charge weight; plus, it is optimized to meet the federal requirements of EER at or near nominal capacities and airflow.

Warranty information: Five-year compressor; one-year parts; and extended warranties are available.

Special installation requirements: This unit follows standard installation practices.

Contact: Rheem Mfg. Co.; www.rheem.com.

eProduct 207

Ruud

Model: Commercial Series™ packaged gas/electric series (RKKL)

Footprint (in inches): 82 to 124 (length) by 48 to 59 (width) by 35 to 57 (height)

Serviceability features: Easy-access panels for the line. Contractors can access the compressor, control box, etc., by removing service panels on the units. The units are equipped with external gauge ports, which enable the compressor service panel to stay in place while the unit is running.

Technical support: Available at 479-648-6237, Monday to Friday, from 8 a.m. to 5 p.m., Central time.

Technical support materials: Spec sheets, wiring diagrams, service/troubleshooting information, installation instructions, and information on parts and part numbers.

Noise-reduction features: Outdoor fans discharge upwards; compressor isolation grommets; insulated panels; and balanced blower wheels and fan blades.

IAQ equipment supported: Two-inch disposable filters included as standard features; insulation with no raw edge exposed; excellent latent to sensible capacity ratios; and a sloped, slide-out cleanable drain pan.

Thermostat compatibility: Compatible with most thermostats.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: The RKKL line leads the industry in unit weight, size, and capacity, the company said. Lighter equipment offered in smaller sizes means that the units are less likely to interfere with other structures on a business’ roof, like exhaust fans, sewer vents, and roof drains.

Warranty information: Five-year compressor; one-year parts; and extended warranties are available.

Special installation requirements: This unit follows standard installation practices.

Contact: Ruud, 479-646-4311; www.ruud.com.

eProduct 208

Tempstar

Model: RGS300-303 packaged gas/electric rooftop

Footprint (in inches): 142 (length) by 87 (width) by 57 (height)

Serviceability features: Units have provisions for through-the-bottom power entry capability. All connections and troubleshooting points located in one convenient place, the master terminal board. Access panels have easy grip handles and no-strip screw feature. Exclusive IGC solid-state control for onboard diagnostics with LED error code designation, burner control logic and energy-saving indoor fan motor delay.

Technical support: Factory-trained Technical Service Advisors (TSAs) on staff at local distributors provide technical assistance, troubleshooting at the local level. ICP technical training is available at field schools held at participating distributor locations.

Technical support materials: Product information posted online at Tempstar dealer website www.gotempstar.com includes product specification sheets, installation, and operation manuals.

Noise-reduction features: Quiet and efficient operation is provided by belt-driven evaporator fans.

IAQ equipment supported: Two-inch return air filters. Optional economizer control accepts CO2 sensor for IAQ capability. Accessory duct-mounted CO2 sensor available for field installation to provide outdoor air for ventilation capability on demand (DCV).

Thermostat compatibility: Compatible with most thermostats.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: Dedicated vertical or horizontal airflow duct configuration models. ASHRAE 90.1-compliant unit features high- and low-pressure switches, freeze-protection thermostats. Scroll compressor has internal line-break overload protection. Factory-installed options include three heat options (high, medium, and low), stainless steel heat exchangers, and high static indoor fan option. Other options include liquid propane/high altitude kits.

Warranty information: 15-year limited stainless steel heat exchanger, 10-year limited aluminized heat exchanger; five-year limited compressor; one-year limited all other parts.

Special installation requirements: None.

Contact: International Comfort Products LLC (ICP), 800-315-4370; www.gotempstar.com.

eProduct 209

Model: RHS240-243 packaged heat pump

Footprint (in inches): 142 (length) by 86 (width) by 49 (height)

Serviceability features: Units have provisions for through-the-bottom power entry capability. All connections and troubleshooting points located in one convenient place, the master terminal board. Access panels have easy grip handles and no-strip screw feature. Large laminated control wiring and power wiring drawings are affixed to the unit to make troubleshooting easy.

Technical support: Factory-trained Technical Service Advisors (TSAs) on staff at local distributors provide technical assistance, troubleshooting at the local level. ICP technical training is available at field schools held at participating distributor locations.

Technical support materials: Product information posted online at Tempstar dealer website www.gotempstar.com includes product specification sheets, installation, and operation manuals.

Noise-reduction features: Quiet and efficient operation is provided by belt-driven evaporator fans.

IAQ equipment supported: Two-inch return air filters. Optional economizer control accepts CO2 sensor for IAQ capability. Accessory duct-mounted CO2 sensor available for field installation to provide outdoor air for ventilation capability on demand (DCV).

Thermostat compatibility: Compatible with most thermostats.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: Dedicated vertical or horizontal airflow duct configuration models. Unit features high- and low-pressure switches, freeze-protection thermostats. Scroll compressor has internal line-break overload protection. Factory-installed options available, including medium and high static indoor fan option.

Warranty information: Five-year limited compressor; one-year limited all other parts.

Special installation requirements: None.

Contact: International Comfort Products LLC (ICP), 800-315-4370; www.gotempstar.com.

eProduct 210

Trane

Model: Force-Flo cabinet heater

Footprint (in inches): Manufacturer did not specify.

Serviceability features: This new ECM product features a touch-safe control, built-in tachometer, and real language LED display, which make servicing simple. Additionally, motor parameters can be adjusted through momentary contact switches in the control box without the use of any additional service tools.

Technical support: Contact local Trane office.

Technical support materials: Catalog, installation and operation manual, along with wiring diagrams are available.

Noise-reduction features: Manufacturer did not specify.

IAQ equipment supported: Upgraded filtration with MERV 8 and MERV 13 filters available as options.

Thermostat compatibility: Compatible with most thermostats.

Replacement parts compatibility: Some shared parts and some unique parts.

Additional features: Commitment to providing premium quality products has led to exclusive use of ECM in all Trane cabinet heaters. These brushless ECMs incorporate the latest technology for optimized energy efficiency (average operating costs on ECM are 50 percent less than permanent split capacitor), acoustical abatement, and extended maintenance-free motor life.

Warranty information: One-year full parts from start-up is standard. Additional parts and labor warranties are available.

Special installation requirements: Manufacturer did not specify.

Contact: Trane; www.trane.com.

eProduct 211

Model: RTWD packaged unit

Footprint (in inches): 148 (length) by 49 (width) by 77 (height)

Serviceability features: Simply reliable and virtually maintenance free. Design simplicity represents the key to RTWD’s reliability. Very few moving parts minimize the chance of breakdown. Required annual maintenance consists of an annual oil analysis. Recommended maintenance is limited to cleaning the condenser tubes as needed.

Technical support: Technical support is available nationwide. Details about local offices and hours can be found on www.trane.com.

Technical support materials: Installation manual (IOM RLC-SVX09G-EN), catalog (RLC-PRC029-EN), LonTalk interface (RF-SLB005-EN), BACnet interface integration guide (BAS-SVP05E-EN), condenser water control (RLC-PRB021-EN), power factor correction (RLC-PRB023-EN), water-side heat recovery (RLC-PRB024-EN), and central geothermal systems (SYS-APM009-EN).

Noise-reduction features: Factory-installed sound attenuation. Insulation is also available in both standard and high humidity options.

IAQ equipment supported: Manufacturer did not specify.

Thermostat compatibility: Manufacturer did not specify.

Replacement parts compatibility: Some shared parts and some unique parts.

Additional features: RTWD can serve a variety of applications. Sometimes chillers need to perform outside traditional comfort conditions and RTWD easily achieves this. It can be configured to produce solution temperatures as low as 10˚F and can also be used in heating mode to generate condenser water temperatures as high as 140˚F.

Warranty information: One-year full parts from start-up is standard. Additional parts and labor warranties are available.

Special installation requirements: Manufacturer did not specify.

Contact: Trane; www.trane.com.

eProduct 212

York

Model: Predator® MagnaDRY packaged unit

Footprint (in inches): 89 (length) by 59 (width) by 42 (height)

Serviceability features: Hinged, tool-free access to blower, filters, compressor, heating, and electrical sections. Slide-out blower for easy service and adjustment. Optional disconnect and powered or nonpowered convenience outlet, side and bottom electrical and condensate drain connections. Simplicity® microprocessor control board with simple, easy-to-use troubleshooting and networking options.

Technical support: Contact distributor.

Technical support materials: Technical guides, installation manuals, and wiring diagrams located at www.yorkupg.com.

Noise-reduction features: Enclosed compressor compartment and closed cell foam insulation greatly improve the sound performance of the product providing a quiet, yet well performing product.

IAQ equipment supported: Composite condensate drain pan, optional 2- or 4-inch air filters with MERV 7 or 13 ratings and CO2 demand control ventilation. Precise humidity control when equipped with the MagnaDRY dehumidification option.

Thermostat compatibility: Compatible with most thermostats.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: The hot gas reheat dehumidification system utilizes a unique patented refrigeration system to ensure responsive performance and provides comfort cooling, or dehumidification when needed. Unlike other products of similar design, the MagnaDRY quickly responds to changing building space temperature or humidity.

Warranty information: Five-year compressor, one-year parts, and 10-year gas heat exchanger. Extended warranties are available.

Special installation requirements: Easy installation made possible with tool-free access panels, solid base rails with fork and rigging access, field convertible for bottom and side duct connections, simple operation of control system.

Contact: Johnson Controls, 414-524-5487; www.yorkhvacdealer.com.

eProduct 213

Model: Predator packaged unit

Footprint (in inches): 89 (length) by 59 (width) by 42 and 50 (height)

Serviceability features: Hinged, tool-free access to blower, filters, compressor, heating, and electrical sections including a slide-out blower. Variable-frequency drive (VFD) mounted on slide-out blower deck for ease of service and programming. Optional disconnect and powered or nonpowered convenience outlet, side and bottom electrical and condensate drain connections.

Technical support: Contact distributor.

Technical support materials: Technical guides, installation manuals, and wiring diagrams located at www.yorkupg.com.

Noise-reduction features: Enclosed compressor compartment and closed cell foam insulation greatly improve the sound performance of the product providing a quiet, yet well-performing product.

IAQ equipment supported: Composite condensate drain pan, optional 2- or 4-inch air filters with MERV 7 or 13 ratings, and CO2 demand control ventilation. Excellent temperature and humidity control over conventional systems when equipped with the variable air volume option.

Thermostat compatibility: Compatible with most thermostats. Operates by controlling space temperature and humidity via Simplicity® Intelli-Comfort™ variable volume unit control.

Replacement parts compatibility: Shares replacement parts with other models.

Additional features: Variable air volume system utilizes a unique control and refrigeration system to ensure responsive performance to provide cooling or heating comfort and proper air volume to independent zones when needed.

Warranty information: Five-year compressor, one-year parts, and 10-year gas heat exchanger. Extended warranties are available.

Special installation requirements: Easy installation made possible with tool-free access panels, solid base rails with fork and rigging access, field convertible for bottom and side duct connections, simple operation of control system.

Contact: Johnson Controls, 414-524-5487; www.yorkhvacdealer.com.

eProduct 214

Publication date: 08/22/2011

PDF - 2011 Commercial Heating Showcase Product Grid