Addison Products Co.
Model:Model DW packaged water-source or geothermal heat pumpFootprint: Three basic cabinet sizes are available.
Economizer availability: Yes; call factory for specific details.
Serviceability features: Hinged access doors with compression latches; field-convertible down flow; left and right horizontal supply and return duct connections; slide-out desiccant wheel assembly; inner liner available for wash down. No tools are required for filter change-out.
Technical support: Available 7 a.m to 5 p.m. Eastern time, Monday through Friday, at 407-292-4400.
Noise-reduction features: Spring-isolated supply, return, and exhaust blowers; 1-inch insulation with gasketed, hinged access doors on insulated 16-gauge base pan.
Indoor air quality features: UV option and HEPA filtration with 2- or 4-inch prefilters available. Modulation hot gas reheat.
Thermostat compatibility: Uses standard commercial unit control systems. It can be ordered with a programmable controller option, or Addison will factory-mount controls provided by others.
Replacement parts compatibility: Many parts are similar to or the same as the DC Series B, DH, and RAH products.
Additional features: Water-source or geothermal heat pump with heat recovery using either a total energy desiccant wheel or a heat pipe system. Optional indirect-fired gas from 75 to 1,600 MBtuh, electric from 5 to 240 kW, and hot water and steam for secondary heat sources.
Warranty information: Available online or by calling the number below. Extended warranties are available.
Special installation requirements: TXV required.
Contact: Addison Products Co., Orlando, Fla.; Attn: Brent Sturgell, 407-292-4400; 407-290-1329 (fax); bsturgell@addison-hvac.com; www.addison-hvac.com.
eProduct #151
American Standard
Model:TSC092A convertible packaged rooftopFootprint: 29.05 square feet
Economizer availability: Yes; field or factory installed.
Serviceability features: Built-in test mode, microcontrols, on-board diagnostics.
Technical support: Contact local American Standard distributor.
Noise-reduction features: Outdoor sound noise level is 87 dBA.
Indoor air quality features: Energy recovery wheels; TXV with face-split evaporator coil. Hot gas reheat coil planned for later this year.
Thermostat compatibility: Compatible with most thermostats and zone sensors. The company offers a full line.
Replacement parts compatibility: Parts are interchangeable.
Additional features: Strong reputation for flexibility and efficiency, the company says.
Warranty information: Extended warranty available. See local distributor for more information.
Special installation requirements: None. Product available with a choice of TXV or short orifice.
Contact: American Standard, Clarksville, Tenn.; Attn: Bill Bauschke, 931-648-5945; 931-648-5901 (fax); bill.bauschke@americanstandard.com; www.americanstandard.com.
eProduct #152
Arcoaire (ICP)
Model:CAE Series 10-ton split air conditionerFootprint (in inches): 59-1/2 (w) by 45-3/4 (d) by 34-1/4 (h)
Economizer availability: Manufacturer did not specify.
Serviceability features: Service ports designed for easy access; high- and low-pressure switches; compressor overload protection.
Technical support: A technical service advisor on staff at local distributors is available for technical assistance and troubleshooting. Technical training is available at ICP Training Center’s Mobile Training Center at locations nationwide and at field schools held at participating distributor locations.
Noise-reduction features: Scroll compressor designed to provide quiet operation.
Indoor air quality features: Manufacturer did not specify.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Standardized parts throughout the commercial split-system line.
Additional features: The Arcoaire CAE Series is ASHRAE 90.1 compliant. The 10-ton model has top-discharge design with a corrosion-resistant wire grille, high- and low-pressure switches, and an anti-cycle timer. It is available in 208/230-, 460-, 575-volt models.
Warranty information: Five-year limited warranty on compressor and one-year limited warranty on parts.
Special installation requirements: Manufacturer did not specify.
Contact: Arcoaire, Nashville, Tenn.; Attn: John Mott, 800-315-4370; 615-383-2215 (fax); john.mott@mottpr.com; www.arcoaire.com.
eProduct #153
Model: CHE Series 7-1/2-ton split heat pump
Footprint (in inches): 33 (w) by 35 (d)
Economizer availability: Manufacturer did not specify.
Serviceability features: Externally mounted gauge ports provide easy access for maintenance and allow for more accurate reading of operating conditions while servicing, the company says.
Technical support: A technical service advisor on staff at local distributors is available for technical assistance and troubleshooting. Technical training is available at ICP Training Center’s Mobile Training Center at locations nationwide and at field schools held at participating distributor locations.
Noise-reduction features: Scroll compressor designed to provide quiet operation. The CHE Series includes suction line accumulators to smooth out refrigerant management during mild ambient conditions and the transitions during defrost operation to eliminate sounds associated with the scroll compressor pumping liquid refrigerant, states the company.
Indoor air quality features: Manufacturer did not specify.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Standardized parts throughout the commercial split-system line.
Additional features: The CHE Series is ASHRAE 90.1 compliant. It has top-discharge design with a corrosion-resistant wire grille, high- and low-pressure switches, and crankcase heater for compressor protection in low ambient conditions. It has 0 degrees F low ambient fan control device and thermostatic expansion valve in outdoor unit for heat pump operation.
Warranty information: Five-year limited warranty on compressor and one-year limited warranty on parts.
Special installation requirements: Manufacturer did not specify.
Contact: Arcoaire, Nashville, Tenn.; Attn: John Mott, 800-315-4370; 615-383-2215; john.mott@mottpr.com; www.arcoaire.com.
eProduct #154
Bard Manufacturing Co.
Model:Q-Tec “Quiet Technology” Series heat pumpFootprint (in inches): 20 (d) by 81-1/4 (h) by 42 to 48 (w)
Economizer availability: Not available.
Serviceability features: All service and maintenance performed inside the building to facilitate multistory installations. All Q-Tec Series models are built on heavy-duty permanent rollers designed for easy installation. Additional service features include ventilation package options, variable-speed ECM indoor blower motor, compressor time-delay relay, solid-state electronic heat pump control, stainless steal drain pans, diagnostic indicator light, and optional dehumidification circuit with hot-gas reheat. Technical support: Available through local Bard distributor network.
Noise-reduction features: Quiet Technology provides extremely low sound levels both indoors and outdoors, the company states.
Indoor air quality features: Variety of ventilation options includes energy recovery ventilator, commercial room ventilator, and a motorized fresh air damper. Barometric fresh air damper is standard. Dehumidification options are also available.
Thermostat compatibility: Unit is available with factory-installed climate control options. It can also be ordered without controls for field installation with heat pump thermostat.
Replacement parts compatibility: Product line shares standard Bard replacement parts.
Additional features: Q-Tec’s Quiet Technology meets or exceeds most classroom sound level requirements and is designed to be installed inside a building structure against an exterior wall, the company states. The Q-Tec eliminates the need for roof-mounted equipment and outside condensing units and can meet many architectural requirements. A variety of ventilation and dehumidification options are available to meet the requirements of the school market. The Q-Tec product line is available as an air-to-air heat pump (QH), a water-to-air heat pump (QW), and a chilled water air conditioner (QC).
Warranty information: Five-year parts warranty.
Special installation requirements: None.
Contact: Bard Manufacturing Co., Bryan, Ohio; Attn: Pam Steel, 419-636-1194; 419-636-2640 (fax); bard@bardhvac.com; www.bardhvac.com.
eProduct #155
Model: SH “Quiet Climate” heat pump
Footprint (in inches): 17 to 22-1/2 (d) by 70-1/2 to 95 (h) by 38 to 42 (w)
Economizer availability: Yes. Check with Bard distributor.
Serviceability features: Scroll compressor, disconnect all models (circuit breakers 230/208-volt and toggle disconnect 460-volt), thermal expansion valve, high-pressure control, compressor time delay relay, solid-state electronic heat pump control, optional ventilation packages, and dehumidification circuit options.
Technical support: Available through local Bard distributor network.
Noise-reduction features: Quiet Technology provides extremely low sound levels both indoors and outdoors, the company says.
Indoor air quality features: Variety of ventilation options includes energy recovery ventilator, economizer, commercial room ventilator, and motorized fresh air damper. Barometric fresh air damper is standard. Dehumidification options are also available.
Thermostat compatibility: Compatible with most heat pump thermostats.
Replacement parts compatibility: Product line shares standard Bard replacement parts.
Additional features: According to the company, Quiet Technology meets and exceeds most classroom sound level requirements. Ventilation and dehumidification options and six cabinet finishes are available.
Warranty information: Five-year parts warranty, five-year compressor warranty, and optional 10-year compressor warranty.
Special installation requirements: None.
Contact: Bard Manufacturing Co., Bryan, Ohio; Attn: Pam Steel, 419-636-1194; 419-636-2640 (fax); bard@bardhvac.com; www.bardhvac.com.
eProduct #156
Carrier
Model:Centurion rooftop Models 48HG and 50HGFootprint (in inches): 169 by 86
Economizer availability: Available.
Serviceability features: Slide-out fan deck, easy-clean coils, and easy-access slide-out filters are available, the company states. Hinged, double-wall doors are standard. ComfortLink® controls with “plain English” display provide run tests, diagnostics, remote monitoring capability, refrigerant pressure and temperature readings, says the company.
Technical support: Call 800-CARRIER (227-7437).
Noise-reduction features: Sound levels rated at 8.17 bels for 13- to 20-ton models and 8.46 bels for the 25-ton unit.
Indoor air quality features: 4-inch filters are available; demand control ventilation capable; and optimum refrigerant circuit initiation for better dehumidification, the company says.
Thermostat compatibility: Compatible with standard thermostats.
Replacement parts compatibility: Shares common parts.
Additional features: Units provide energy efficiency at all tonnages and very low sound levels, the company states.
Warranty information: One year on the unit, five years on compressors, and 10 years on the heat exchangers are all standard. A variety of extended warranties are available for parts and labor.
Special installation requirements: None.
Contact: Carrier Corp., Syracuse, N.Y.; 800-227-7437; contact.carrier@carrier.utc.com; www.carrier.com.
eProduct #157
Model: COBRA 48/50HJ004-014 RTU with factory-installed energy recycler
Footprint (in inches): 3- to 6-ton base: 50-1/8 (w) by 101-1/2 (l); 7-1/2 to 12-1/2 ton: 58-7/8 (w) by 127 (l)
Economizer availability: Outside air damper is standard.
Serviceability features: Hinged access to control box, compressor(s); optional DDC available; removal panels standard.
Technical support: Call 800-CARRIER (227-7437) to complement installation, startup, and service instructions supplied with every COBRA unit.
Noise-reduction features: Manufacturer did not specify.
Indoor air quality features: COBRA unit’s E$R section provides latent control of outside air and RTU section’s DX coil and optional MoistureMi$er dehumidification option provide ID latent control, all controlled by Thermidistat (combination thermostat, electronic time clock, and humidistat).
Thermostat compatibility: Can use standard thermostat in conjunction with humidistat to control E$R section.
Replacement parts compatibility: Uses standard Energy Star-rated 48/50HJ RTU section.
Additional features: Utilizes energy in return air (exhaust air) to precondition ventilation air (to satisfy ASHRAE 62-01, 15 to 20 cfm/person) being brought in OA damper of E$R. Employs standard heat pump technology, simplifying maintenance compared to heat wheel cleaning procedure, the company states.
Warranty information: Five-year compressor warranty, 10 years on gas heat exchanger. Optional additional labor and extended parts warranties are available.
Special installation requirements: COBRA fits on standard RTU roof curb. A “sleeper” rail is available to support E$R end if desired and a “full perimeter” roof curb is available with split return duct design available to accommodate two return air ducts. E$R utilizes TXV for optimal low-load performance.
Contact: Carrier Corp., Syracuse, N.Y.; 800-227-7437; contact.carrier@carrier.utc.com; www.carrier.com.
eProduct #158
ClimateMaster
Model:Genesis Compact packaged heat pumpFootprint (in inches): Manufacturer did not specify.
Economizer availability: Manufacturer did not specify.
Serviceability features: Manufacturer did not specify.
Technical support: Manufacturer did not specify.
Noise-reduction features: Mute package option.
Indoor air quality features: Manufacturer did not specify.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts.
Additional features: Compact size.
Warranty information: One year.
Special installation requirements: Capillary tube used.
Contact: ClimateMaster, Oklahoma City; Attn: Scott Stevens, 405-745-6000; 405-745-4102 (fax); sstevens@climatemaster.com; www.climatemaster.com.
eProduct #159
Coleman
Model:Commercial split system (HL model)Footprint (in inches): 37-1/2 by 45-3/4 by 128
Economizer availability: Not available.
Serviceability features: Permanently lubricated condenser and evaporator fan motor bearings need no annual maintenance, the company says.
Technical support: First level of support provided by distribution; factory support available by calling 877-874-7378 (877-UPG-SERV). Support is available from 7 a.m. to 5 p.m. Central time.
Noise-reduction features: Every unit includes a well-insulated cabinet to help keep sound levels very low, states the company.
Indoor air quality features: Manufacturer did not specify.
Thermostat compatibility: Manual and electronic two-stage thermostats are available for cooling applications.
Replacement parts compatibility: Manufacturer did not specify.
Additional features: ASHRAE 90.1-1999 compliant.
Warranty information: Five-year limited warranty on compressor; one-year limited warranty on all other parts.
Special installation requirements: Manufacturer did not specify.
Contact: Coleman, Norman, Okla.; Attn: Mickey Smith, 405-419-6541; 405-419-6359 (fax); mickey.smith@york.com; www.colemanac.com.
eProduct #160
Comfort-Aire (Heat Controller)
Model:RS181A split A/C condensing unitFootprint (in inches): 80 (w) by 31 (d) by 35-3/4 (h)
Economizer availability: Not available.
Serviceability features: Pull-off panel makes it easy to access components for service, the company says. Sweat connections are external.
Technical support: Technical support line available at 517-787-2100 from 8 a.m. to 5 p.m. Eastern time on weekdays.
Noise-reduction features: Manufacturer did not specify.
Indoor air quality features: Manufacturer did not specify.
Thermostat compatibility: Uses regular thermostat.
Replacement parts compatibility: The line includes units from 89,000 to 240,000 Btuh, units share replacement parts.
Additional features: Compact size and energy efficiency.
Warranty information: One-year limited warranty.
Special installation requirements: None.
Contact: Comfort-Aire, Jackson, Mich.; Attn: LeeAnne Perkins, 517-787-2100; 517-787-9341 (fax); lperkins@heatcontroller.com; www.heatcontroller.com.
eProduct #161
Comfortmaker (ICP)
Model:CAE Series 10-ton split air conditionerFootprint (in inches): 59-1/2 (w) by 45-3/4 (d) by 34-1/4 (h)
Economizer availability: Manufacturer did not specify.
Serviceability features: Service ports designed for easy access; high- and low-pressure switches; compressor overload protection.
Technical support: A technical service advisor on staff at local distributors is available for technical assistance and troubleshooting. Technical training available at ICP Training Center’s Mobile Training Center at locations nationwide and at field schools held at participating distributor locations.
Noise-reduction features: Scroll compressor designed to provide quiet operation.
Indoor air quality features: Manufacturer did not specify.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Standardized parts throughout the commercial split-system line.
Additional features: The CAE Series is ASHRAE 90.1 compliant. It features a single-circuit scroll compressor. It has top-discharge design with a corrosion-resistant wire grille, high- and low-pressure switches, and an anti-cycle timer. It is available in 208/230-, 460-, 575-volt models.
Warranty information: Five-year limited warranty on compressor and one-year limited warranty on parts.
Special installation requirements: Manufacturer did not specify.
Contact: Comfortmaker, Nashville, Tenn.; Attn: John Mott, 800-315-4370; 615-383-2215 (fax); john.mott@mottpr.com; www.comfortmaker.com.
eProduct #162
Model: CHE Series 7-1/2-ton split heat pump
Footprint (in inches): 33 (w) by 35 (d)
Economizer availability: Manufacturer did not specify.
Serviceability features: Externally mounted gauge ports provide easy access for maintenance and allow for more accurate reading of operating conditions while servicing, the company states.
Technical support: A technical service advisor on staff at local distributors is available for technical assistance and troubleshooting. Technical training available at ICP Training Center’s Mobile Training Center at locations nationwide and at field schools held at participating distributor locations.
Noise-reduction features: Scroll compressor designed for quiet operation. The CHE Series includes suction line accumulators that smooth out refrigerant management during mild ambient conditions and the transitions during defrost operation to eliminate sounds associated with the scroll compressors pumping liquid refrigerant, the company says.
Indoor air quality features: Manufacturer did not specify.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Standardized parts throughout the commercial split-system line.
Additional features: The CHE Series 7-1/2-ton, three-phase, split-system heat pump is ASHRAE 90.1 compliant. It has top-discharge design with a corrosion-resistant wire grille, high- and low-pressure switches, and crankcase heater for compressor protection in low ambient conditions. Electronic defrost control is designed to ensure a fast, efficient defrost cycle.
Warranty information: Five-year limited warranty on compressor and one-year limited warranty on parts.
Special installation requirements: Manufacturer did not specify.
Contact: Comfortmaker, Nashville, Tenn.; Attn: John Mott, 800-315-4370; 615-383-2215 (fax); john.mott@mottpr.com; www.comfortmaker.com.
eProduct #163
Friedrich Air Conditioning Company
Model:Wall-mount packaged air conditioners and heat pumps (OES/OHS Series)Footprint (in inches): 1-1/2 to 2 ton: 33 (w) 71.1 (h) by 22 (d); 2-1/2 to 3 ton: 40 (w) by 71.1 (h) by 22 (d); 3-1/2, 4, and 5 ton: 41.9 (w) by 85 (h) by 27 (d)
Economizer availability: Available as a factory-installed ventilation option.
Serviceability features: Front-side service access: circuit breakers, slide-out blower, and electric heater assembly. Slide-out filters provide easy access, states the company.
Technical support: Available at 210-357-4400, ext. 723.
Noise-reduction features: Manufacturer did not specify.
Indoor air quality features: Manufacturer did not specify.
Thermostat compatibility: Compatible with most thermostats, depending on application.
Replacement parts compatibility: Some cabinet sizes share the same size panels.
Additional features: Scroll compressor is standard (1-1/2- and 2-ton models utilize a rotary compressor). Full biflow TXV is the standard refrigerant regulating device on heat pumps, and a single TXV is standard on the air conditioning units. Plastic drain pan and a coil freeze sensor are standard. Also included are two-speed twin blowers for quiet operation; automatic freeze protection; industry standard supply and return air openings; standard manual fresh air damper; “easy-mount” brackets, which are adaptable to competitors’ cabinet widths; 20-gauge galvanized steel cabinet with a powder paint finish; high- and low-pressure controls for system protection (low-pressure controls only standard on heat pumps). Filter brackets will accept 1- or 2-inch air filters.
Warranty information: Varies depending on application.
Special installation requirements: Manufacturer did not specify.
Contact: Friedrich Air Conditioning Company, San Antonio, Texas; Attn: Sales Department, 800-541-6645; 210-357-4480 (fax); hvac.sales@friedrich.com; www.friedrich.com.
eProduct #164
Global Energy Group Inc.
Model:Inventor Series 1400 packaged unitsFootprint (in inches): 59 (w) by 50 (h) by 118 (d)
Economizer availability: Available.
Serviceability features: Hinged access doors; sight glass per refrigerant circuit. State-of-the-art control board can be connected to building automation system, the company says.
Technical support: Available 8 a.m. to 5 p.m. Eastern time, Monday through Friday at 727-372-3939.
Noise-reduction features: All units rated at 83 dBA.
Indoor air quality features: E-Coil for humidity control at full- and part-load conditions (part load to include two-speed fan option); condensate pump removal system. Powered exhaust comes standard on all units.
Thermostat compatibility: Common thermostats can be used.
Replacement parts compatibility: Common parts throughout, except for evaporator and condenser coils.
Additional features: Up to 13.5 EER; base unit can be upgraded in the field for humidity control. Uses patented technologies designed to attain the new standard in high efficiency.
Warranty information: One-year parts, five-year compressor.
Special installation requirements: None.
Contact: Global Energy Group Inc., Odessa, Fla.; Attn: Todd Van Hyfte, 727-372-3939; 727-376-1929 (fax); info@gegsolutions.com; www.gegsolutions.com.
eProduct #165
Goodman Manufacturing Co.
Model:CKL090 and CKL120 split systemsFootprint (in inches): 35-1/2 by 35-1/2
Economizer availability: Not available.
Serviceability features: Single-panel access to controls; brass sweat service valves with gauge ports.
Technical support: Dealer and distributor technical support available at 388-593-7988.
Noise-reduction features: Quiet condenser fan with wire fan discharge grille.
Indoor air quality features: Manufacturer did not specify.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: The products share components with other Goodman products.
Additional features: Louvered metal condenser guard; factory-installed high- and low-pressure switches; scroll compressors; factory-installed filter-driers. Units meet ASHRAE Standard 90.1.
Warranty information: Five-year limited warranty.
Special installation requirements: The CKL090 and CKL120 are rated with Goodman air handlers.
Contact: Goodman Manufacturing Co., Houston; Attn: Al Knight, 713-861-2500, ext. 660; 713-861-0772 (fax); alknight2@goodmanmfg.com; www.goodmanmfg.com.
eProduct #166
Heil (ICP)
Model:CAE Series 7-1/2-ton split air conditionerFootprint (in inches): 33 (w) by 35 (d)
Economizer availability: Manufacturer did not specify.
Serviceability features: Externally mounted gauge ports designed to provide easy access for maintenance and allow for more accurate reading of operating conditions while servicing.
Technical support: A technical service advisor on staff at local distributors is available for technical assistance and troubleshooting. Technical training available at ICP Training Center’s Mobile Training Center at locations nationwide and at field schools held at participating distributor locations.
Noise-reduction features: The units are built with scroll compressors designed for quiet operation. The CAE Series includes suction line accumulators that smooth out refrigerant management during mild ambient conditions and the transitions during defrost operation to eliminate sounds associated with the scroll compressors pumping liquid refrigerant, the company states.
Indoor air quality features: Manufacturer did not specify.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Standardized parts throughout the commercial split-system line.
Additional features: The CAE Series 7-1/2-ton, three-phase, split-system air conditioner is ASHRAE 90.1 compliant. It features tandem scroll compressors with one refrigerant circuit. It has top-discharge design with a corrosion-resistant wire grille, high- and low-pressure switches, and crankcase heater for compressor protection in low ambient conditions.
Warranty information: Five-year limited warranty on compressor and one-year limited warranty on parts.
Special installation requirements: Manufacturer did not specify.
Contact: Heil, Nashville, Tenn.; Attn: John Mott, 800-315-4370; 615-383-2215 (fax); john.mott@mottpr.com; www.heil-hvac.com.
eProduct #167
Model: CHE Series 10-ton split heat pump
Footprint (in inches): 59-1/2 (w) by 45-3/4 (d) by 34-1/4 (h)
Economizer availability: Manufacturer did not specify.
Serviceability features: Service ports designed for easy access. Units have high- and low-pressure switches and feature compressor overload protection.
Technical support: A technical service advisor on staff at local distributors is available for technical assistance and troubleshooting. Technical training available at ICP Training Center’s Mobile Training Center at locations nationwide and at field schools held at participating distributor locations.
Noise-reduction features: The units are built with scroll compressors designed for quiet operation. The compressor is mounted on vibration isolators. The CHE Series includes suction line accumulators that smooth out refrigerant management during mild ambient conditions and the transitions during defrost operation to eliminate sounds associated with the scroll compressors pumping liquid refrigerant, the company says.
Indoor air quality features: Manufacturer did not specify.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Standardized parts throughout the commercial split-system line.
Additional features: The CHE Series 10-ton, three-phase, split-system heat pump is ASHRAE 90.1 compliant; comes in 208/230- and 460-volt models; and has an energy efficiency ratio (EER) of 10.1. It has top-discharge design with a corrosion-resistant wire grille, high- and low-pressure switches, and an anti-cycle timer.
Warranty information: Five-year limited warranty on compressor and one-year limited warranty on parts.
Special installation requirements: Manufacturer did not specify.
Contact: Heil, Nashville, Tenn.; Attn: John Mott, 800-315-4370; 615-383-2215 (fax); john.mott@mottpr.com; www.heil-hvac.com.
eProduct #168
ICP Commercial
Model:CAE Series 7-1/2-ton split air conditionerFootprint (in inches): 33 (w) by 35 (d)
Economizer availability: Manufacturer did not specify.
Serviceability features: Externally mounted gauge ports provide easy access for maintenance and allow for more accurate reading of operating conditions while servicing, the company states.
Technical support: A technical service advisor on staff at local distributors is available for technical assistance and troubleshooting. Technical training available at ICP Training Center’s Mobile Training Center at locations nationwide and at field schools held at participating distributor locations.
Noise-reduction features: The CAE Series models are built with scroll compressors designed for quiet operation. The units are equipped with suction line accumulators that smooth out refrigerant management during mild ambient conditions and the transitions during defrost operation to eliminate sounds associated with the scroll compressors pumping liquid refrigerant, states the company.
Indoor air quality features: Manufacturer did not specify.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Standardized parts throughout the commercial split-system line.
Additional features: The CAE Series features tandem scroll compressors with one refrigerant circuit. These three-phase air conditioners are ASHRAE 90.1 compliant, have top-discharge design with a corrosion-resistant wire grille, and high- and low-pressure switches. A heavy-duty coil guard is offset to protect the coil from accidental damage.
Warranty information: Five-year limited warranty on compressor and one-year limited warranty on parts.
Special installation requirements: Manufacturer did not specify.
Contact: ICP Commercial, Nashville, Tenn.; Attn: John Mott, 800-315-4370; 615-383-2215 (fax); john.mott@mottpr.com; www.icpcommercial.com.
eProduct #169
Model: CHE Series 10-ton split heat pump
Footprint (in inches): 59-1/2 (w) by 45-3/4 (d) by 34-1/4 (h)
Economizer availability: Manufacturer did not specify.
Serviceability features: Service ports designed for easy access. Units have high- and low-pressure switches and feature compressor overload protection.
Technical support: A technical service advisor on staff at local distributors is available for technical assistance and troubleshooting. Technical training available at ICP Training Center’s Mobile Training Center at locations nationwide and at field schools held at participating distributor locations.
Noise-reduction features: The CHE Series is equipped with scroll compressors mounted on vibration isolators designed for quiet operation. Features include suction line accumulators that smooth out refrigerant management during mild ambient conditions and the transitions during defrost operation to eliminate sounds associated with the scroll compressors pumping liquid refrigerant, the company says.
Indoor air quality features: Manufacturer did not specify.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Standardized parts throughout the commercial split-system line.
Additional features: This product is ASHRAE 90.1 compliant. It has top-discharge design with a corrosion-resistant wire grille, high- and low-pressure switches, crankcase heater, compressor overload protection, and anti-short-cycle protection. It is available in 208/230- and 460-volt models.
Warranty information: Five-year limited warranty on compressor and one-year limited warranty on parts.
Special installation requirements: Manufacturer did not specify.
Contact: ICP Commercial, Nashville, Tenn.; Attn: John Mott, 800-315-4370; 615-383-2215 (fax); john.mott@mottpr.com; www.icpcommercial.com.
eProduct #170
Lennox Industries Inc.
Model:L Series packaged rooftopFootprint (in inches): Manufacturer did not specify.
Economizer availability: Available. Cost depends on specific units and contractor/dealer price.
Serviceability features: Integrated Modular Control unit controller features an easy-to-read LED display, which can diagnose over 85 unit functions and provide alarm codes and diagnostic history information, the company states. Tool-less access doors, color-coded and numbered wiring, an isolated compressor compartment and slide-out blower deck are designed to make accessing the unit’s components easy and efficient. Slab (non-bent) outdoor coils on units larger than 6 tons reduce cleaning time, the company says.
Technical support: Customer service is available from 8 a.m. to 5 p.m. Central time at 800-4LENNOX (453-6669).
Noise-reduction features: Manufacturer did not specify.
Indoor air quality features: The Humiditrol® dehumidification system is available on the 3- to 25-ton models. This system is designed to improve indoor air quality by providing dehumidification on demand without overcooling the room. MERV 11 filters are available for improved air filtration. The units are demand control system ready, needing only the addition of a CO2 sensor, the company states.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models in the line.
Additional features: Gas/electric units feature stainless or aluminized steel heat exchangers, direct-spark ignition, electronic flame sensor, and combustion air inducer. Can perform fresh air tempering without additional controls. Able to achieve high levels of heat at altitudes up to 4,500 feet without derating, the company states.
Warranty information: Five-year limited compressor warranty; 15-year limited parts warranty on stainless steel gas heat exchangers; 10-year limited warranty on aluminized gas heat exchangers; three-year limited warranty on Integrated Modular Control unit controller; and one-year limited warranty on all remaining components.
Special installation requirements: Manufacturer did not specify.
Contact: Lennox Industries Inc., Richardson, Texas; Attn: Mike Walker, 972-467-6124; 972-497-5112 (fax); mike.walker@lennoxind.com; www.lennox.com.
eProduct #171
Luxaire
Model:HF Model split-system air conditionerFootprint (in inches): 44-9/32 by 76-7/8 by 39-7/8
Economizer availability: Manufacturer did not specify.
Serviceability features: Gauge lines extend out from cabinet to facilitate servicing.
Technical support: First level of support provided by distribution; factory support available by calling 877-874-7378 (877-UPG-SERV). Support is available from 7 a.m. to 5 p.m. Central time.
Noise-reduction features: Manufacturer did not specify.
Indoor air quality features: Manufacturer did not specify.
Thermostat compatibility: Manufacturer did not specify.
Replacement parts compatibility: Manufacturer did not specify.
Additional features: ASHRAE 90-1.1999 compliant.
Warranty information: Five-year compressor warranty; one year on other parts.
Special installation requirements: Manufacturer did not specify.
Contact: Luxaire, Norman, Okla.; Attn: Mark Ritz, 405-419-6537; 405-419-6359 (fax); mark.ritz@york.com; www.luxaire.com.
eProduct #172
Mammoth Inc.
Model:N Vintage water-source heat pump (WSHP); Vari-ZoneFootprint (in inches): WSHP: Smaller sizes: 31 (w) by 11 (h) by 20 (d); larger sizes: 52 (w) by 21 (h) by 27 (d); Vari-Zone: approximately 58 (h) by 96 (w) by 250 (d).
Economizer availability: WSHP: Waterside economizer is a factory-mounted option, and cost depends on size. Vari-Zone: Outdoor air economizer is a standard feature.
Serviceability features: WSHP: Three access panels to fan, compressor, and control box sections allow easy access to all components without removal of unit from the ceiling, the company states; fan and motor can be easily removed. Vari-Zone: Full-size hinged and latched access doors to all major components are designed to facilitate ease of maintenance and service. Keyed latches are available.
Technical support: Technical support is available both from the factory and local, authorized service agencies.
Noise-reduction features: WSHP: Components selected for quiet operation. Optional factory-mounted sound attenuation package is available. Vari-Zone: Slow-rotating unhoused airfoil fans and scroll compressors minimize sound levels. Perforated liners are available (factory mounted) for additional attenuation. Variable-frequency drive modulates fan motor to reduce sound levels when full air volume is not required.
Indoor air quality features: Hot-gas reheat coil helps the WSHP maintain proper humidity; separate line of WSHP make-up air units deliver the proper amount of outside air to meet code requirements; optional 2-inch filter rack accommodates higher efficiency filters. With the Vari-Zone, a constant percentage of outdoor air is delivered to each zone to meet IAQ requirements. Filtration efficiencies up to 95 percent are available.
Thermostat compatibility: WSHP is compatible with most thermostats. The Vari-Zone is primarily controlled by DDC systems supplied by Mammoth or the local controls contractor. This ensures the thermostat and unit controls are compatible. Can also interface with existing control systems and thermostats in replacement applications.
Replacement parts compatibility: WSHP: Most parts are common, except for sizing due to capacity differences. Vari-Zone: also designed to achieve a high degree of parts standardization.
Additional features: The WSHP is smaller and quieter than most competitive models, the company states, plus it allows ease of access to major components. The Vari-Zone employs a simple two-deck design with a bypass of outdoor air to improve energy efficiency and reduce operating costs. Separate hot, cold, and ventilation decks eliminate any mixing of hot and cold air. Complies with ASHRAE Standard 90.1 for energy efficiency. Bypass duct provides continuous ventilation to improve IAQ. The use of a variable-frequency drive is available to provide additional energy savings.
Warranty information: The WSHP has a standard one-year parts warranty. A five-year compressor warranty is optional. The Vari-Zone has a standard one-year parts warranty. A five-year compressor warranty and 10-year heat exchanger warranty are optional.
Special installation requirements: There are no special installation requirements for the WSHP. With the Vari-Zone, if replacing an existing unit, field measurement and coordination is required if unit is to mount on existing curb, zone dividers are to match existing dividers and power connections are to match existing locations. There are no special requirements for new construction.
Contact: Mammoth Inc., Chaska, Minn.; Attn: Patty Hegre, 952-361-2711; 952-361-2801 (fax); phegre@mammoth-inc.com; www.mammoth-inc.com.
eProduct #173
Marvair
Model:XcelPac air conditioner, Model AVEFootprint (in inches): 30 by 26
Economizer availability: Economizers are not available in the XcelPac air conditioner. Only available in the ComPac II™ line of air conditioners and the Classic™ line of heat pumps.
Serviceability features: Compressor and the electrical compartment are in the front of the unit, eliminating need for left- and right-hand units. Filter designed for easy access. Service access valves are standard. The service disconnect must be removed before the panel to the electrical compartment can be removed.
Technical support: Service and installation support available 24 hours a day, seven days a week by calling a toll-free number: 888-726-2734.
Noise-reduction features: Compressor compartment lined with thermal/acoustical insulation. Large, slow-speed condenser fan.
Indoor air quality features: Zero- to 15-percent fresh air standard with a manually adjustable damper. Optional kit can provide up to 30 percent fresh air.
Thermostat compatibility: Compatible with all standard air conditioning thermostats.
Replacement parts compatibility: Many of the parts are common throughout Marvair’s complete line of air conditioners.
Additional features: A single motor for both the evaporator blower and the condenser fan.
Warranty information: One year all parts and five years on the compressor. Extended warranties are available.
Special installation requirements: Sloped top sheds water, minimizing chance of water leaks. Unit has built-in mounting flanges. Top flashing piece and bottom mounting bracket are packaged with each unit. Metal rails on base are designed to facilitate lifting of the unit by a forklift. Electrical knockouts are on the back and both sides of unit. No field charging required.
Contact: Marvair, Atlanta; Attn: David Shuford, 404-848-9281; 404-848-9115 (fax); dshuford@airxcel.com; www.marvair.com.
eProduct #174
Mitsubishi Electric
Model:City Multi R2 variable refrigerant flow zoning systemFootprint (in inches): Varies depending on unit.
Economizer availability: Manufacturer did not specify.
Serviceability features: Inverter-driven scroll compressor. Unit serviceable from front and back.
Technical support: Manufacturer did not specify.
Noise-reduction features: Indoor unit range is 24 to 49 dBA. PURY80TMU: 56 dBA. PURY100TMU: 57 dBA.
Indoor air quality features: Exceptional humidity control because system is constantly running and indoor units are within the zone, unlike unitary ducted and chiller type systems, the company states.
Thermostat compatibility: City Multi has an extensive array of unit and system controllers. City Multi can be tied into a building’s existing control network like LonWorks™.
Replacement parts compatibility: Replacement parts are shared within the product family.
Additional features: This system has the ability to simultaneously heat and cool a building. It uses inverter motor and compressor technologies to achieve truly consistent comfort levels, the company says. Up to 16 indoor units can be connected to a single outdoor unit with combined capacities up to 12.5 tons (with the PURY100TMU). These systems are designed to be complete zoning systems for total system control from one source. They have refrigerant delivery and control systems that enable variable refrigerant flow to each indoor unit for precise comfort conditioning to each zone while saving on energy costs, states the company.
Warranty information: Six-year compressor and one-year parts. Extended warranty program is available for Diamond Designers.
Special installation requirements: Manufacturer did not specify.
Contact: Mitsubishi Electric, Lawrenceville, Ga.; Attn: Mike Smith, 678-376-2900; 678-376-3540 (fax); info@hvac.mea.com; www.mitsubishielectric.com/hvac.
eProduct #175
Reznor/Thomas & Betts Corp.
Model:Modular Air Processing System (MAPS)Footprint (in inches): 45 (w) by 70 (h) by 145 (l)
Economizer availability: Available. Adds 2 percent to 10 percent to the unit cost, depending on options.
Serviceability features: Manufacturer did not specify.
Technical support: Manufacturer did not specify.
Noise-reduction features: Manufacturer did not specify.
Indoor air quality features: Dedicated outside air unit with full reheat.
Thermostat compatibility: Special thermostat.
Replacement parts compatibility: Shares parts.
Additional features: Reheat dehumidification cycle.
Warranty information: Up to five-year compressor and 10-year limited gas heat exchanger warranty.
Special installation requirements: Requires TXV.
Contact: Reznor, Memphis, Tenn.; 800-695-1901; 901-252-1305 (fax); hvacadmin@tnb.com; www.reznoronline.com.
eProduct #176
Rheem Air Conditioning
Model:RAWE high-efficiency condensing unitsFootprint (in inches): 43 (l) by 31 (w)
Economizer availability: Manufacturer did not specify.
Serviceability features: Units feature control box with separation between line and control voltages, as well as compressor and other refrigerant controls that are accessible through removable panel without affecting normal operation of the unit. Condenser fan motors are mounted on removable top panels, which bring the motors out and expose entire condenser coil for cleaning. Lug for field connection of ground wire.
Technical support: Available 8 a.m. to 5 p.m. Monday through Friday at 479-648-4900.
Noise-reduction features: The scroll compressor is hermetically sealed with internal high-temperature protection and durable insulation on motor windings. The entire compressor is mounted on rubber grommets to reduce vibration and noise.
Indoor air quality features: Manufacturer did not specify.
Thermostat compatibility: Manufacturer did not specify.
Replacement parts compatibility: Manufacturer did not specify.
Additional features: The size ranges offered by Rheem allow you to mix or match components to meet actual job requirements, thus eliminating the need to use oversized or undersized equipment. Equipment sized to meet the actual load will provide better operating economy, better humidity control, and longer equipment life, the company states.
Warranty information: Five-year compressor warranty, one-year whole unit warranty, and one-year parts warranty. Extended warranty available.
Special installation requirements: Manufacturer did not specify.
Contact: Rheem Air Conditioning, Fort Smith, Ark; Attn: Service Technician Representatives, 479-648-4900; 479-648-4918 (fax); www.rheemac.com.
eProduct #177
Samsung (Quietside Corp.)
Model:AD26B1C2Footprint (in inches): 31.1 by 9.7 by 6.5
Economizer availability: Manufacturer did not specify.
Serviceability features: Automatic reset after power failure; detachable front grille.
Technical support: Available 8 a.m. to 5 p.m. Pacific time at 562-463-0880.
Noise-reduction features: Sound in/out 42/59 dB.
Indoor air quality features: Antibacterial filter, electrostatic filter, deodorizing filter, washable front grille.
Thermostat compatibility: Wireless remote control.
Replacement parts compatibility: Many replacement parts are interchangeable.
Additional features: Compact, light, and has five feature modes.
Warranty information: Five years compressor, one year parts.
Special installation requirements: Size properly. Use standard installation methods. Use clean piping. Stay within operation and installation guidelines.
Contact: Samsung, Whittier, Calif.; Attn: Jack Ernest, 562-463-0880; 562-463-5665 (fax); jacke@quietside.com; www.quietside.com.
eProduct #178
Model: DVM RVMH100CBMO
Footprint (in inches): 39 by 69-1/2 by 30.7
Economizer availability: Manufacturer did not specify.
Serviceability features: Flexible piping options; automatic reset after power failure; detachable front grille; full diagnostics and Internet capability.
Technical support: Available 8 a.m. to 5 p.m. Pacific time at 562-463-0880.
Noise-reduction features: Sound 59 dB.
Indoor air quality features: Antibacterial filter, electrostatic filter, deodorizing filter, washable front grille, biotech-coated coils, 35 degree F evaporator, low-cfm constant fan.
Thermostat compatibility: Wired or wireless remote control or centralized PC control.
Replacement parts compatibility: Many replacement parts are interchangeable.
Additional features: Variable capacity; supports up to 16 indoor units that can be multiplexed for 256 zones. According to the company, it is suitable for retrofits, and multiple styles of indoor units are available.
Warranty information: Five years compressor, one year parts.
Special installation requirements: Size properly. Use standard installation methods. Use clean piping. Stay within operation and installation guidelines. Expansion valves are included.
Contact: Samsung, Whittier, Calif.; Attn: Jack Ernest, 562-463-0880; 562-463-5665 (fax); jacke@quietside.com; www.quietside.com.
eProduct #179
Sanyo Fisher Company
Model:24KLS62R ductless air conditionerFootprint (in inches): Outdoor: 36-5/8 (h) by 37 (w) by 13-3/8 (d); Indoor: 13 (h) by 44-7/8 (w) by 9 (d).
Serviceability features: Service valves.
Technical support: Available Monday through Friday from 8:30 a.m. to 5:00 p.m. at 800-851-1235.
Noise-reduction features: Indoor 38 dBA/Outdoor 55 dBA
Indoor air quality features: Dry mode, anti-mold filter, optional ceramic filter (designed to remove cigarette smoke, unpleasant odors, etc.).
Thermostat compatibility: Unit is equipped with a wireless remote control.
Replacement parts compatibility: Shares some components with other models in the line.
Additional features: This is the only 13-SEER ductless split-system A/C unit on the market, the company claims. It is rebate eligible. Low ambient operation.
Warranty information: One year parts, five years compressor.
Special installation requirements: Simple installation requiring only a 3.5-inch access hole in the exterior wall.
Contact: Sanyo Fisher Company, Chatsworth, Calif.; Attn: Tom Crock or Susan Bass, 818-998-7322; 818-701-4170 (fax); sbass@sfc.sanyo.com; www.sanyohvac.com.
eProduct #180
Tempstar (ICP)
Model:CAE Series 7-1/2-ton split air conditionerFootprint (in inches): 33 (w) by 35 (d)
Economizer availability: Manufacturer did not specify.
Serviceability features: Easy access for maintenance is provided by externally mounted gauge ports that allow for more accurate reading of operating conditions while servicing, the company says.
Technical support: A technical service advisor on staff at local distributors is available for technical assistance and troubleshooting. Technical training available at ICP Training Center’s Mobile Training Center at locations nationwide and at field schools held at participating distributor locations.
Noise-reduction features: Scroll compressors provide quiet operation in CAE models. The 7-1/2-ton units are equipped with suction line accumulators to help eliminate sounds associated with the scroll compressors pumping liquid refrigerant.
Indoor air quality features: Manufacturer did not specify.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Standardized parts throughout the commercial split-system line.
Additional features: The CAE Series features tandem scroll compressors with one refrigerant circuit. These three-phase air conditioners are ASHRAE 90.1 compliant, have top-discharge design with a corrosion-resistant wire grille, and high- and low-pressure switches. Copper tube/aluminum fin coils are designed to provide improved heat transfer.
Warranty information: Five-year limited warranty on compressor and one-year limited warranty on parts.
Special installation requirements: Manufacturer did not specify.
Contact: Tempstar, Nashville, Tenn.; Attn: John Mott, 800-315-4370; 615-383-2215 (fax); john.mott@mottpr.com; www.tempstar.com.
eProduct #181
Model: CHE Series 10-ton split heat pump
Footprint (in inches): 59-1/2 (w) by 45-3/4 (d) by 34-1/4 (h)
Economizer availability: Manufacturer did not specify.
Serviceability features: Service ports designed for easy accessibility; high- and low-pressure switches; compressor overload protection.
Technical support: A technical service advisor on staff at local distributors is available with technical assistance and troubleshooting. Technical training available at ICP Training Center’s Mobile Training Center at locations nationwide and at field schools held at participating distributor locations.
Noise-reduction features: The CHE 10-ton models are equipped with scroll compressors mounted on vibration isolators. They include suction line accumulators designed to help eliminate sounds associated with the scroll compressors pumping liquid refrigerant.
Indoor air quality features: Manufacturer did not specify.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Standardized parts throughout the commercial split-system line.
Additional features: This product is equipped with state-of-the-art electronic defrost control, the company states. It is ASHRAE 90.1 compliant and has top-discharge design with a corrosion-resistant wire grille. For system safety, it includes high- and low-pressure switches, crankcase heater, compressor overload protection, and anti-short cycle protection. It is available in 208/230- and 460-volt models.
Warranty information: Five-year limited warranty on compressor and one-year limited warranty on parts.
Special installation requirements: Manufacturer did not specify.
Contact: Tempstar, Nashville, Tenn.; Attn: John Mott, 800-315-4370; 615-383-2215 (fax); john.mott@mottpr.com; www.tempstar.com.
eProduct #182
Trane
Model:Precedent TSC092AFootprint: 29.05 square feet
Economizer availability: Available either as field or factory installed.
Serviceability features: Built-in test mode, microcontrols, on-board diagnostics.
Technical support: Contact local Trane distributor.
Noise-reduction features: Outdoor sound noise level 87 dBA.
Indoor air quality features: Energy recovery wheels; TXV with face-split evaporator coil. Hot gas reheat coil planned for 2003.
Thermostat compatibility: Compatible with most thermostats and zone sensors. Trane offers a full line.
Replacement parts compatibility: Parts are interchangeable.
Additional features: Strong reputation for flexibility and efficiency.
Warranty information: Extended warranty available. See local distributor for more information.
Special installation requirements: None. Product available with a choice of TXV or short orifice.
Contact: Trane, Clarksville, Tenn.; Attn: Tony Cameron, 931-221-3681; 931-648-5901 (fax); tony.cameron@trane.com; www.trane.com.
eProduct #183
York UPG
Model:Predator Magnum single package rooftop unit (DJ Model)Footprint (in inches): Single 50-3/4 (h) by 59 (w) by 119-7/16 (d) cabinet size with a common 50-1/2 (w) by 80-5/8 (d) footprint
Economizer availability: Electronic enthalpy automatic economizers are available. Contact York distributor for costs.
Serviceability features: Tool-free maintenance with features like hinged doors for all access panels and slide-out blower and blower motor tray.
Technical support: First level of support provided by distribution; factory support available by calling 877-874-7378 (877-UPG-SERV). Support is available from 7 a.m. to 5 p.m. Central time.
Noise-reduction features: Manufacturer did not specify.
Indoor air quality features: IAQ features such as foil-faced insulation, pitched roof, and removable drain pan.
Thermostat compatibility: Manufacturer did not specify.
Replacement parts compatibility: Manufacturer did not specify.
Additional features: Advanced Simplicity Control boards come standard on every unit. Every unit is ASHRAE 90.1-1999 compliant.
Warranty information: Five-year compressor warranty, 10-year heat assembly warranty, one year on other parts.
Special installation requirements: Manufacturer did not specify.
Contact: York UPG, Norman, Okla.; Attn: Andy Fracica, 405-419-6563; 405-419-6545 (fax); andy.fracica@york.com; www.yorkupg.com.
eProduct #184
Model: Sunline Magnum single package rooftop unit (DJ Model)
Footprint (in inches): 52-5/8 by 92 by 181
Economizer availability: Single-input electronic enthalpy economizers are available. Contact local York distributor for costs.
Serviceability features: Permanently lubricated condenser and evaporator fan motor bearings need no annual maintenance.
Technical support: First level of support provided by distribution, factory support available by calling 877-874-7378 (877-UPG-SERV). Support is available from 7 a.m. to 5 p.m. Central time.
Noise-reduction features: Manufacturer did not specify.
Indoor air quality features: Manufacturer did not specify.
Thermostat compatibility: Manufacturer did not specify.
Replacement parts compatibility: Manufacturer did not specify.
Additional features: Advanced Simplicity Control boards come standard on every unit. Every unit is ASHRAE 90.1-1999 compliant.
Warranty information: Ten years on heat exchangers, five years on compressors, and one year on other parts.
Special installation requirements: Manufacturer did not specify.
Contact: York UPG, Norman, Okla.; Attn: Andy Fracica, 405-419-6563; 405-419-6545 (fax); andy.fracica@york.com; www.yorkupg.com.
eProduct #185
Publication date: 04/14/2003
