AirEase
Model: 4SHP14 heat pump
Footprint (inches): 29 (length) by 31 (width) by 38 (height)
Serviceability features: Removable (two screws) louvered panels to access coils. Double and single concentric knockouts for electrical connections. Ground lugs standard. Corner-mounted service valves for access. Defrost control with built-in diagnostics.
Technical support: Available at 800-515-3501 Monday-Friday, 8 a.m.-5 p.m. Eastern.
Technical support materials: Wiring diagram, troubleshooting information, installation data performance, parts and accessories documentation are available.
Noise-reduction features: High-density sound blanket, antivibration compressor pads, and sound-reducing fan discharge top.
IAQ equipment supported: Compatible with most IAQ products.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: Robust dual fuel offering from 13-18 SEER. Compatible with various types of air handlers including wall mount, soffit, and high-velocity.
Warranty information: Ten-year compressor, 10-year parts (with registration).
Special installation requirements: None.
Contact: Allied Air Enterprises, 803-738-4000; www.alliedair.com.
eProduct 160
Model: A952V variable-speed, stainless furnace
Footprint (inches): 28 (length) by 18-25 (width) by 33 (height)
Serviceability features: Five-fault code recall; external drain trap with clean-out port; slide-out blower; operational with heating compartment door off; access to the flame sensor and igniter with forward facing fasteners; two-piece door design for access to components.
Technical support: Available at 800-515-3501.
Technical support materials: Wiring diagrams, service/troubleshooting information, installation instructions, parts finder/look-up tools, contractornet website, spec sheets, training CDs.
Noise-reduction features: Variable-speed motor, multistage heating, enclosed burner, fully sealed service doors, insulated blower compartment.
IAQ equipment supported: Manufacturer did not specify.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: Only 33 inches tall, gas furnace has stainless steel clamshell primary heat exchanger.
Warranty information: Ten-year parts and lifetime heat exchanger warranty (with registration).
Special installation requirements: Manufacturer did not specify.
Contact: Allied Air Enterprises, 803-738-4000; www.alliedair.com.
eProduct 161
Amana
Model: ACVM96 gas furnace
Footprint (inches): 21 (length) by 28 (width) by 40(height)
Serviceability features: Designed for multiposition installation. Convenient left or right connection for gas and electric service. Easy-install venting is standard; alternate flue/vent locations available. When installed with a ComfortNet® communicating system control the unit displays a wide variety of fault codes and service features.
Technical support: Available local distributors or factory direct at 888-593-9988.
Technical support materials: All are available from local distributors, factory direct, or downloaded.
Noise-reduction features: Efficient and quiet variable-speed motor. Fully insulated heavy-gauge steel cabinet. Foil faced insulation lines heat exchanger section.
IAQ equipment supported: This unit easily connects to myriad IAQ products, including filtration, humidification, and many more.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: The Million-Air® stainless steel tubular heat exchanger has successfully cycled over 2.3 million times, and it’s still going. It has a stainless steel secondary heat exchanger, and the self-calibrating modulating gas valve operates on two- or single-stage thermostats with delivery performance from 35-100 percent capacity. This unit is ComfortNet communicating control compatible.
Warranty information: Limited lifetime unit replacement and 10-year parts limited.
Special installation requirements: When installed as a ComfortNet communicating system component, the unit system is automatically configured.
Contact: Amana Heating and Cooling Systems, 713-861-2500; www.amana-hac.com.
eProduct 162
Model: ASZC18 heat pump
Footprint (inches): 35 (length) by 35 (width) by 38 (height)
Serviceability features: Top and side maintenance access panels. Single panel access to controls with space provided for field-installed accessories. Sweat connections service valves with access to gauge ports. Factory-installed bi-flow filter-drier.
Technical support: Available local distributors or factory direct at 888-593-9988.
Technical support materials: All are available from local distributor or factory direct and at www.amana-hac.com or PartnerLink.
Noise-reduction features: High-density foam compressor sound blanket. SmartShift™ technology with short-cycle protection to ensure quiet, reliable defrost. Amana brand designed sound control top. Factory-installed discharge muffler. Quiet ECM-style condenser fan motor.
IAQ equipment supported: Compatible with all residential IAQ components.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: Expanded ComfortAlert diagnostics built-in. SmartShift technology, factory-installed: filter-drier, compressor crankcase heater band, suction line accumulator, discharge line muffler, high- and low-pressure switch, and coil and ambient temperature sensors. ComfortNet compatible.
Warranty information: Limited lifetime unit replacement.
Special installation requirements: When installed as part of a ComfortNet communicating system, only two low-voltage wires are required.
Contact: Amana Heating and Cooling Systems, 713-861-2500; www.amana-hac.com.
eProduct 163
American Standard Heating and Air Conditioning
Model: Platinum XV (AAM7) air handler
Footprint (inches): Manufacturer did not specify.
Serviceability features: Modular cabinet disassembles for single person installation. Cabinet-front sight glass allows circuit board diagnostic lights to be viewed without door panel removal. Coil and blower pull out thanks to an exclusive new integrated rail system. Panel identifiers and quarter-turn fasteners facilitate easier installation and service.
Technical support: Contact local American Standard distributor.
Technical support materials: The ASDealerNet intranet site for American Standard dealers and distributors allows quick access to the most current support materials — including catalog pages, installer guides, service facts, dealer sheets, product data, submittals, and owners’ manuals.
Noise-reduction features: The Vortica™ blower is designed for quiet, efficient operation, using less energy than conventional blowers to deliver more air, while reducing energy consumption, carbon emissions, and noise. In addition, the Air-Tite™ II cabinet with double wall construction and enclosed foam insulation provides quiet operation year-after-year.
IAQ equipment supported: Fully enclosed insulation eliminates loose fibers that may enter the airstream with other air handlers. Add the AccuClean™ whole-home air filtration system for advanced air filtration that removes up to 99.98 percent of unwanted particles and allergens from a home’s filtered air.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: Constructed more like a refrigerator than a typical air handler, with insulation fully enclosed between double-walls of the innovative Air-Tite II cabinet, preventing condensation. In addition to eliminating sweating, the cabinet eliminates the loose fibers from fiberglass insulation that may enter the airstream with other air handlers.
Warranty information: One-year base limited. 10-year functional parts limited is available if the product is registered within 60 days of installation. Optional extended warranties are also available.
Special installation requirements: Can be configured four different ways without repositioning the coil or drain pan. To make transportation and installation more convenient, the air handler disassembles into four pieces, each weighing less than 48 pounds, and will fit through small openings like attic access doors.
Contact: American Standard Heating & Air Conditioning, 903-581-3467; www.americanstandardair.com.
eProduct 164
Model: Platinum ZM (A2GW) hydronic packaged unit
Footprint (inches): Manufacturer did not specify.
Serviceability features: Large lift-out panels provide access from all four sides and controls can be placed on either end to improve serviceability.
Technical support: Contact local American Standard distributor.
Technical support materials: The ASDealerNet intranet site for American Standard dealers and distributors allows quick access to the most current support materials — including catalog pages, installer guides, service facts, dealer sheets, product data, submittals, and owners’ manuals.
Noise-reduction features: The fully insulated cabinet with foil-backed insulation is designed to reduce noise levels. Specially designed vibration damping mounts on the compressor deliver near silent operation.
IAQ equipment supported: Manufacturer did not specify.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: This water heating and cooling system uses renewable energy from inside the earth and can provide radiant heating without blown air or ductwork.
Warranty information: Ten-year parts and labor.
Special installation requirements: Installation includes a large, fluid-filled loop that consists of an underground pipe system. There are four different configurations available for installation.
Contact: American Standard Heating & Air Conditioning, 903-581-3467; www.americanstandardair.com.
eProduct 165
Arcoaire
Model: DLX 96 gas furnace
Footprint (inches): 29 (length) by 14-25 (width) by 35 (height)
Serviceability features: Sturdy knobs allow service technicians to remove and replace furnace doors with a twist of the wrist. A super-bright LED makes diagnostic flash codes easier to read. Blower assembly is mounted on rails for easier, upfront installation and removal. Lets technicians see latest fault code even if power shuts off.
Technical support: Technical Service Advisor on staff at local distributors is available with technical assistance, troubleshooting. Technical training is available 24/7/365 online and at field schools held at participating distributor locations nationwide.
Technical support materials: Product information posted online at dealer website includes product spec sheets, installation-operation manuals, and technical support/parts manuals.
Noise-reduction features: The blower motor of the new 96 percent furnaces is attached with soft-mount rubber grommets that absorb sound and vibration. Furnaces feature insulated heat exchanger and blower compartments to muffle sound and absorb vibration noise.
IAQ equipment supported: When coupled with a condensing unit and humidity-capable thermostat, mainline Arcoaire furnaces can control relative humidity during cooling operations. These furnaces have a dehumidification function in cooling mode and can control a humidifier accessory in heating mode.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Some shared parts, some unique.
Additional features: Designed for four-way multiposition installation, 35 inches tall, and lighter weight than previous counterparts. Comes with ECM blower motors that can deliver an increase in cooling efficiency when paired with select condensing units and evaporator coils. Meets low-NOx emissions standards.
Warranty information: One-year No Hassle Replacement™ limited. Lifetime heat exchanger and 10-year parts limited to original purchaser with timely registration. Limited warranty period is 20-year heat exchanger and five-year parts if not registered within 90 days of installation (see warranty certificate for details and restrictions).
Special installation requirements: None.
Contact: International Comfort Products LLC (ICP), 800-315-4370; www.goarcoaire.com.
eProduct 166
Model: IIX 96 gas furnace
Footprint (inches): 29 (length) by 14-25 (width) by 35 (height)
Serviceability features: Blower assembly is mounted on rails for easier, upfront installation and removal. These new gas furnaces feature large, robust one-quarter turn knobs for door installation and removal. A super-bright LED makes diagnostic flash codes easier to read. Lets technicians see most recent fault code even if power shuts off.
Technical support: Technical Service Advisor on staff at local distributors is available with technical assistance, troubleshooting. Technical training is available 24/7/365 online and at field schools held at participating distributor locations nationwide.
Technical support materials: Product information posted online at the dealer website includes product spec sheets, installation-operation manuals, and technical support/parts manuals.
Noise-reduction features: The blower motor is attached with soft-mount rubber grommets that absorb sound and vibration. Furnaces feature insulated heat exchanger and blower compartments to muffle sound and absorb vibration noise.
IAQ equipment supported: When coupled with a condensing unit and humidity-capable thermostat, mainline furnaces can control relative humidity during cooling operation. These furnaces have a dehumidification function in cooling mode and can control a humidifier accessory in heating mode.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Some shared parts, some unique.
Additional features: Designed for four-way multiposition installation, just 35 inches tall and lighter weight than previous counterparts, these two-stage models feature ECM blower motors that can deliver an increase in cooling efficiency when paired with select condensing units and evaporator coils. Meets low-NOx emissions standards.
Warranty information: Five-year No Hassle Replacement limited. Lifetime heat exchanger and 10-year parts limited to original purchaser with timely registration. Limited warranty period is 20-year heat exchanger and five-year parts if not registered within 90 days of installation (see warranty certificate for details and restrictions).
Special installation requirements: None.
Contact: International Comfort Products LLC (ICP), 800-315-4370; www.goarcoaire.com.
eProduct 167
Armstrong Air
Model: A951E constant torque, stainless furnace
Footprint (inches): 29 (length) by 18-25 (width) by 33 (height)
Serviceability features: Ten-fault code recall; external drain trap with clean-out port; slide-out blower; operational with heating compartment door off; access to the flame sensor and igniter with forward facing fasteners; two-piece door design for access to components.
Technical support: Available at 800-515-3501.
Technical support materials: Wiring diagrams, service-troubleshooting information, installation instructions, parts finder/look-up tools, contractornet website, spec sheets, training CDs.
Noise-reduction features: High-efficiency constant torque motor and insulated blower compartment.
IAQ equipment supported: Manufacturer did not specify.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: Only 33-inch-tall gas furnace with stainless steel clamshell primary heat exchanger. Constant torque motor meets 2 percent efficiency standard requirement for tax credit eligibility.
Warranty information: One-year parts and lifetime heat exchanger (with registration).
Special installation requirements: Manufacturer did not specify.
Contact: Allied Air Enterprises, 803-738-4000; www.alliedair.com.
eProduct 168
Model: A96MV modulating furnace
Footprint (inches): 28 (length) by 18-24 (width) by 33 (height)
Serviceability features: Ten-fault code recall; external drain trap with clean-out port; slide-out blower; operational with heating compartment door off; access to the flame sensor and igniter with forward facing fasteners; two-piece door design for access to components.
Technical support: Available at 800-515-3501.
Technical support materials: Wiring diagrams, service/troubleshooting information, installation instructions, parts finder/look-up tools, contractonet website, spec sheets, training CDs.
Noise-reduction features: Variable-speed motor, multistage heating, enclosed burner, fully sealed service doors, insulated blower compartment.
IAQ equipment supported: Manufacturer did not specify.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: Only 33-inch tall gas furnace with stainless steel clamshell primary heat exchanger.
Warranty information: Ten-year parts and lifetime heat exchanger (with registration).
Special installation requirements: Manufacturer did not specify.
Contact: Allied Air Enterprises, 803-738-4000; www.alliedair.com.
eProduct 169
Bard Manufacturing Co.
Model: Geo-Tec geothermal heat pump
Footprint (inches): 26-27 (length) by 28-33 (width) by 48-56 (height)
Serviceability features: Features two-stage step capacity scroll compressor, R-410A refrigerant, and variable-speed ECM motor for superior efficiencies and quiet performance. Installation and service features include left- or right-side water connections outside of cabinet; left- or right-hand access to control panel; slide-in electric heat packages; and simplified wiring and troubleshooting.
Technical support: In-house and field training classes available. Service provided through distribution network.
Technical support materials: Service parts guides, wiring diagrams, installation manuals, (printed and cd formats), website.
Noise-reduction features: Copeland scroll step-capacity compressor; variable-speed ECM blower motor designed for soft start-up; compressor/service compartment insulated to reduce noise levels.
IAQ equipment supported: Compatible with field installed electronic air cleaner or high-efficiency media type filters through the installing dealers.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: Suitable for ground water or ground loop applications. Features multicapacity two-stage compressor, variable-speed ECM blower motor, R-410A, Energy Star certified, built-in domestic hot water heat exchanger, COP ratings up to 5.4, and EER ratings up to 30.6.
Warranty information: Ten-year parts, 10-year compressor.
Special installation requirements: None.
Contact: Bard Manufacturing Co., 419-636-1194; www.bardhvac.com.
eProduct 170
Model: Geo-Trio geothermal heat pump
Footprint (inches): Varies.
Serviceability features: Multi-position system, suitable for upflow, downflow, horizontal left or right, split and dual fuel configurations. Step capacity two-stage scroll compressor, R-410A, variable-speed ECM motor, domestic hot water heat exchanger system, high- and low-pressure switches standard, insulated high efficiency coaxial water coil. All water and refrigerant connections on outside of cabinet for ease of installation. Energy Star certified.
Technical support: Available through local Bard distribution network.
Technical support materials: Service parts guides, wiring diagrams, installation manuals (printed and digital), website.
Noise-reduction features: Compressor/service compartment insulated to reduce noise levels, variable-speed ECM blower motor and step-capacity two-stage compressor with double isolation mounting system designed for quieter operation.
IAQ equipment supported: Compatible with field installed electronic air cleaner or high-efficiency media type filters through installing dealer.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: Three separate sections (A-coil, blower coil, and compressor) are each self-contained, allowing for multiple configurations (upflow, downflow, horizontal left or right as split system, and dual fuel). Fewer SKUs with more product offering.
Warranty information: Five-year parts, 10-year compressor standard. If registered, 10-year all parts.
Special installation requirements: Manufacturer did not specify.
Contact: Bard Manufacturing Co., 419-636-1194; www.bardhvac.com.
eProduct 171
Broan
Model: FG7SD/M gas furnace
Footprint (inches): 28 (length) by 14-25 (width) by 35 (height)
Serviceability features: Low height makes this furnace easier to apply in low-ceiling applications; works well with taller, high-SEER coils. Diagnostic lights provide troubleshooting without counting flashes. A color-coded wire harness is designed for ease of service and replacement.
Technical support: Available at 800-422-4328 Monday-Friday, 8 a.m.-4:30 p.m. Central.
Technical support materials: Wiring diagrams, replacement parts lists, installation instructions available via dealer log-in website or www.nordyneu.com.
Noise-reduction features: Sealed and insulated blower compartment and sealed vestibule.
IAQ equipment supported: Integrated control board with connections for electronic air cleaner and humidifier.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: All furnaces are 100 percent fired and tested on the manufacturing line. Includes packaging with a corner post design to ensure that the product arrives damage-free to the homeowner.
Warranty information: With product registration, 10-year all parts and 10-year Quality Pledge to replace entire unit if the heat exchanger fails.
Special installation requirements: Manufacturer did not specify.
Contact: Nordyne, 636-561-7300; www.broanhvac.net.
eProduct 172
Model: FT4BI heat pump
Footprint (inches): 31 (length) by 31 (width) by 37-45 (height)
Serviceability features: Inverter-driven rotary compressor provides fully variable operation. Full-port brass ball valves provide low pressure drop and ease of service. The valves are actuated by quarter-turn full open to full close. Compressor and control access. Diagnostics provided by communicating controller.
Technical support: Available at 800-422-4328 Monday-Friday, 8:00 a.m.-4:30 p.m. Central.
Technical support materials: Technical specs, wiring diagrams, and installation instructions are available on www.nordyneu.com. Technical literature and training videos are available on dealer log-in marketing site and www.nordyneu.com.
Noise-reduction features: Compressor sound blanket, composite base pan, and swept wing fan blade reduce unwanted noise. Operation is as low as 59 dB.
IAQ equipment supported: Air cleaners, humidifiers, UV lights, and iQ Zone zoning.
Thermostat compatibility: Requires a special thermostat.
Replacement parts compatibility: Some shared parts, some unique.
Additional features: Fully variable-speed inverter-driven rotary compressor technology and variable-speed indoor and outdoor motors. Operates near the nominal rated capacity at the thermostat setpoint and modulates as the temperatures change. System may run at additional 18 percent capacity to provide rapid cooling. A built-in humidity control activates humidifier equipment (if supplied), and reduces blower speed if indoor relative humidity is greater than setpoint (default is 60 percent).
Warranty information: Ten-year all parts and 10-year Quality Pledge to replace the entire unit if its compressor fails within the first 10 years of operation to the original owner. All split system products must be installed with a matched indoor air handler or indoor coil to qualify. Consumer product registration required within a limited period of time after installation.
Special installation requirements: Dealers must be factory certified before selling or installing an iQ Drive system.
Contact: Nordyne, 636-561-7300; www.broanhvac.net.
eProduct 173
Bryant
Model: Evolution® System 986T two-stage furnace
Footprint (inches): 29 (length) by 14-25 (width) by 35 (height)
Serviceability features: Large twist knobs make door removal/replacement easier. Remove two screws, and blower assembly slides out on rails. Main wiring harness is long enough to allow technicians to remove/service blower without disconnecting wires. Brighter fault-code LED is easier to read. Fault codes stay in memory even after power shuts off.
Technical support: Provided through nationwide network of local distributors.
Technical support materials: Installation and startup instructions, troubleshooting guide, critical parts list, and wiring diagram on www.HVACpartners.com.
Noise-reduction features: Variable-speed blower motor reduces operating sound levels. Special blower mount quiets vibration and cuts sound. Cabinet insulation absorbs sound from heat exchanger and blower compartments.
IAQ equipment supported: Compatible with Perfect Humidity® technology, Perfect Air™ purifier, and additional IAQ products.
Thermostat compatibility: Requires a special thermostat. Evolution® control recommended for full feature functionality. Compatible with most thermostats but with reduced functionality.
Replacement parts compatibility: Some shared parts, some unique.
Additional features: Two-stage heat and two-stage cooling compatible with variable-speed blower motor. At just 35 inches tall, it is designed for four-way, multiposition installation.
Warranty information: Lifetime heat exchanger and 10-year parts limited to original purchaser with timely registration. Limited warranty period is 20-year heat exchanger and five-year parts if not registered within 90 days of installation (warranty certificate provides details and restrictions).
Special installation requirements: None.
Contact: Bryant Heating & Cooling Systems, 888-994-7237; www.bryant.com.
eProduct 174
Model: Evolution® System 987M modulating furnace
Footprint (inches): 29 (length) by 18-25 (width) by 35 (height)
Serviceability features: Blower assembly slides out on rails after the removal of two screws. Main wiring harness is long enough to allow technicians to remove/service blower without disconnecting wires. Large twist knobs make access easier. Brighter fault-code LED is easier to read. Fault codes stay in memory even after power shuts off.
Technical support: Support provided through nationwide network of local distributors.
Technical support materials: Installation and startup instructions, troubleshooting guide, critical parts list, and wiring diagram on www.HVACpartners.com.
Noise-reduction features: These new furnaces include a quiet variable-speed ECM blower motor to minimize operating sound levels and a variable-speed ECM inducer motor that matches motor speed to furnace operating conditions to help keep sound levels as low as possible. They feature insulated heat exchanger and blower compartments to muffle sound and absorb vibration noise.
IAQ equipment supported: Compatible with Perfect Humidity technology, Perfect Air purifier, and additional IAQ products.
Thermostat compatibility: Requires a special thermostat. Evolution control recommended for full feature functionality. Compatible with most thermostats but with reduced functionality.
Replacement parts compatibility: Some shared parts, some unique.
Additional features: A new modulating gas valve matches the furnace’s heating output to the home’s heating needs to provide precise heating power for maximum comfort. True multiposition design allows installation as upflow, downflow, horizontal-right or horizontal-left with 97 percent AFUE performance in all configurations. Only 35 inches tall.
Warranty information: Lifetime heat exchanger and 10-year parts limited to original purchaser with timely registration. Limited warranty period is 20-year heat exchanger and five-year parts if not registered within 90 days of installation (warranty certificate provides details and restrictions).
Special installation requirements: None.
Contact: Bryant Heating & Cooling Systems, 888-994-7237; www.bryant.com.
eProduct 175
Carrier
Model: 25VNA Infinity® heat pump with Greenspeed™ intelligence
Footprint (inches): 35 (length) by 35 (width) by 44 (height)
Serviceability features: Communication between system components allows the Infinity control to display system history for faster diagnosis. Ability to attach second control to outdoor unit allows service without entering the home. Control lets technicians access system remotely via the Internet to prepare for service call in advance.
Technical support: Support provided through nationwide network of local distributors.
Technical support materials: Installation and startup instructions, troubleshooting guide, critical parts list, and wiring diagram on www.HVACpartners.com.
Noise-reduction features: Systems achieve low sound ratings with quiet motor mounts, a compressor sound blanket, forward swept fan blades, a laminated sound elimination compressor mounting plate, and a top with integrated silencer airflow baffle. Variable-speed compressor and variable-speed ECM blower motors operate at quieter, lower speeds most of the time.
IAQ equipment supported: Compatible with Carrier IAQ system components, including humidifiers, ventilators, germicidal UV lamps, and Infinity air purifier. Infinity control features Ideal Humidity® functionality, which monitors and controls both temperature and humidity, allowing the heat pump to effectively manage humidity year-round.
Thermostat compatibility: Requires a special thermostat. Infinity control recommended for full feature functionality. Compatible with most thermostats but with reduced functionality.
Replacement parts compatibility: Some shared parts, some unique.
Additional features: Highest heating efficiency ducted, air-source heat pump available. Variable-speed capacity control enables better heating capacity as the outdoor temperature drops, resulting in less reliance on auxiliary heat. Also achieves cooling efficiencies of up to 20 SEER. Makes state-of-the-art variable-speed technology available with ease of installation, service and maintenance.
Warranty information: Ten-year parts limited (including compressor) with timely registration (restrictions apply; see warranty certificate for details).
Special installation requirements: None.
Contact: Carrier Corp., 800-946-2930; www.residential.carrier.com.
eProduct 176
Model: 59MN7 Infinity 98 furnace with Greenspeed intelligence
Footprint (inches): 29 (length) by 18-25 (width) by 35 (height)
Serviceability features: Infinity control allows remote Internet access to system to prepare for service call in advance. Non-volatile memory allows technicians to see fault code history even if power has been shut off. Large, twist door attachments make access easier. Remove two screws and blower assembly slides out on rails.
Technical support: Support provided through nationwide network of local distributors.
Technical support materials: Installation and startup instructions, troubleshooting guide, critical parts list, and wiring diagram on www.HVACpartners.com.
Noise-reduction features: Modulating gas valve lets furnace run at quieter, lower fire rates most of the time. Variable-speed ECM blower and inducer motors can operate at quieter, lower speeds. Insulation dampens sound in heat exchanger and blower sections of cabinet. Blower motor is mounted on soft-mount rubber grommets to reduce sound.
IAQ equipment supported: Compatible with Carrier IAQ system components, including humidifiers, ventilators, germicidal UV lamps, and Infinity air purifiers.
Thermostat compatibility: Requires a special thermostat. Infinity control recommended for full functionality. Compatible with most thermostats but with limited functionality.
Replacement parts compatibility: Some shared parts, some unique.
Additional features: Greenspeed intelligence raises modulating gas valve output 40-100 percent of capacity in one-percentage-point increments for precise comfort. Cabinets are 35 inches tall. Multi-positional design allows conversion to upflow, downflow or horizontal right/left. Rotating 360-degree vent elbow allows for venting flexibility.
Warranty information: Lifetime heat exchanger and 10-year parts limited to original purchaser with timely registration. Limited warranty period is 20-year heat exchanger and five-year parts if not registered within 90 days of installation (see warranty certificate for details and restrictions).
Special installation requirements: None.
Contact: Carrier Corp., 800-946-2930; www.residential.carrier.com.
eProduct 177
Century
Model: GTUV B Series gas furnace
Footprint (inches): 30 (length) by 18-21 (width) by 34 (height)
Serviceability features: Front panels remove with thumb screws for ready access to components. Four diagnostic LEDs on furnace control indicate operation, flame, cfm or power condition by steady on, blinking, or off, which helps simplify service.
Technical support: Available 8 a.m.-5 p.m. Eastern weekdays, at 517-787-2100.
Technical support materials: Installation, Operation and Maintenance Manual (including wiring diagrams and comprehensive troubleshooting guide) and parts list are available on website or by email from customer service department.
Noise-reduction features: Insulated blower compartment, specially designed inducer system, slow-opening gas valve, and soft-start ECM blower motor make this one of the quietest furnaces on the market, the company said.
IAQ equipment supported: Two-stage operation maintains constant airflow across a wide range of external static pressures in the air ducts, resulting in better indoor air quality and humidity level. A permanent, washable filter makes it easier to keep a clean filter in place.
Thermostat compatibility: Compatible with most thermostats. Two-stage recommended for optional efficiency.
Replacement parts compatibility: Some shared parts, some unique.
Additional features: Two-stage design saves energy by running at low stage most of the time, ramping up to high stage only when there’s demand. ComfortMax control integrates gas valve and blower to eliminate temperature swings while saving energy. Two heat exchangers and two-stage gas valve provide maximum fuel efficiency. Includes multiple protection features. Cabinet is lightweight and compact.
Warranty information: Limited lifetime on both heat exchangers. Five-year limited parts. All parts have additional seven-year warranty (total of 12 years) to the original owner of a single family residential installation, when the unit and any a/c that is part of the system are installed as an ARI-matched system with Heat Controller components, providing the unit is registered within 90 days of the purchase. Other limitations apply; see warranty on website for details.
Special installation requirements: Connections for gas, electricity, and condensate drain can be made on the left or right side; optional indoor or outdoor combustion air; combustion air may be piped to either the top or side of the cabinet (special molded fitting provided). Unit is a/c ready and includes connections for other comfort options such as electronic air cleaner and/or humidifier.
Contact: Century Div. Heat Controller, 517-787-2100; www.century-hvac.com.
eProduct 178
Model: Patriot 80 Model ODHA oil furnace
Footprint (inches): 59 (length) by 21-24 (width) by 21-24 (height)
Serviceability features: Furnace panels are removable to reach components and entire blower assembly slides out for access. Stainless steel clean-out ports are located to simplify complete servicing. LEDs on the Advanced Burner Control system flash or stay on to indicate problems, helping the technician with diagnosis.
Technical support: Available 8 a.m.-5 p.m. Eastern weekdays, at 517-787-2100.
Technical support materials: Installation, Operation and Maintenance Manual (including wiring diagrams) and parts list are available on website or by email from customer service department.
Noise-reduction features: Furnace is lined with foil-faced high density insulation to minimize noise and heat loss. High temperature ceramic combustion chamber provides quiet, high-efficiency combustion.
IAQ equipment supported: Filters must be installed in the return duct system; filter kits are available.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: Advanced burner control includes technician pump prime mode, limited reset and limited recycle, plus welded relay protection; also has programmable delays for “valve on” and “motor off.” Two communication ports allow addition of alarm contacts and future wireless communications. Multi-speed direct drive blower assembly has handy plug-in wiring. Prewired to add a/c.
Warranty information: Limited lifetime heat exchanger; five-year limited other parts. Some limitations apply; see printed warranty on website for details. AssurancePlus® extended service agreements available.
Special installation requirements: For horizontal installation, unit can be installed on non-combustible base or suspended; knock-outs on top panel accommodate hanger rods (not supplied). Multi firing rate capability requires a simple nozzle change to adjust firing rate; unit is shipped with larger firing rate. Furnace discharges warm air to the left side; airflow can be reversed for horizontal or converted to counterflow in the field.
Contact: Century Div. Heat Controller, 517-787-2100; www.century-hvac.com.
eProduct 179
ClimateMaster
Model: Tranquility 22 Digital Series (TZ) packaged unit
Footprint (inches): 26 (length) by 22 (width) by 48 (height)
Serviceability features: Multiple side removable panels offering installation and service access. Its swing-out style control box provides access for maintenance and repairs. The integral digital communicating controller provides comprehensive set up and diagnostic capabilities with the variable-speed geothermal source pump, fan motor, and thermostat.
Technical support: Available at 405-745-6000.
Technical support materials: All wiring diagrams, installation instructions, and submittals are available online.
Noise-reduction features: An attention to detail such as tubing design and eliminating metal-to-metal contact along with dual stage compressor vibration isolation, flexible rubber motor mounting, and insulated heavy-gauge steel cabinet combine to make an extremely quiet unit.
IAQ equipment supported: The multistage capacity and selectable dehumidification fan settings along with pleated MERV-8 air filter and air-handling compartment lined with washable foil faced insulation add up to a very IAQ friendly product.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: Product incorporates high-end features like a two-stage compressor, Energy Star Tier 3 efficiency, variable-speed fan, communicating digital controls, and true plug-and-play functionality at a very competitive price point. It also has one of the industry’s smallest footprint, making it suitable for installation in tight places.
Warranty information: Standard limited express is available with coverage of 18 months from time of shipment or 12 months from startup, whichever comes first. Optional warranties include four-year control board, four-year compressor, and four-year refrigerant.
Special installation requirements: Manufacturer did not specify.
Contact: ClimateMaster Inc., 405-745-6000; www.climatemaster.com.
eProduct 180
Coleman
Model: HC6B Echelon split system heat pump
Footprint (inches): 37-42 (length) by 31-34 (width) by 40 (height)
Serviceability features: A slide-down control compartment allows access to control components, and angled service valves reduce overall installation time and cost. A full-end, full-service access panel ensures entry to internal components. When integrated with the Echelon Communicating Control, advanced control and diagnostic capabilities makes servicing the unit even easier.
Technical support: First level of support is provided by the distributor. Factory support is available to distributors and dealers by calling 877-874-7378, 7 a.m.-6 p.m. Eastern.
Technical support materials: A full technical guide and installation instructions including wiring diagrams, sizes, parts, accessories, part number and installation instructions, are available online or by request.
Noise-reduction features: Incorporates the WhisperDrive™ System, a group of features specifically engineered to reduce sound. The system consists of a molded composite bulkhead that isolates the compressor from the rest of the unit, a unique, swept-wing fan design that allows air to flow smoothly and efficiently across the fan tips, a molded composite base pan, and a sturdy fan guard.
IAQ equipment supported: Compatible with Coleman brand indoor products, including filters, humidifiers, and UV lights.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: Offers a new control board that communicates with all key components in a home comfort system. Also utilizes a microprocessor defrost control system that provides optimal comfort and monitors the overall system for reliable operation, automatically shutting the unit down if improper operating conditions occur.
Warranty information: Standard five-year limited parts, 10-year limited compressor, and Premium System Warranty, which is limited lifetime compressor when matched with an approved furnace or UPG air handler and coil. Extended 10-year limited parts when product is registered online within 90 days of purchase for replacement or closing for new home construction.
Special installation requirements: Unit is the outdoor part of a versatile heat pump system designed for convenient serviceability and installation. These communicating heat pumps can identify themselves to the Coleman Communicating Control, allowing for faster setup and more powerful diagnostics.
Contact: Johnson Controls, 414-524-4338; www.colemanhvacdealer.com.
eProduct 181
Comfort-Aire
Model: Patriot 80 Highboy oil furnace
Footprint (inches): 31-33 (length) by 20-23 (width) by 54 (height)
Serviceability features: Removable panels allow access to components. Blower assembly slides out for service and maintenance. Stainless steel clean-out ports are easily accessed for complete servicing of heat exchanger. Burner control indicator lights simplify diagnostics. Features standard components should replacement parts be needed at some time.
Technical support: Available 8 a.m.-5 p.m. Eastern weekdays, at 517-787-2100.
Technical support materials: Installation, Operation and Maintenance Manual (including wiring diagrams) and parts list are available on website or by email from customer service department.
Noise-reduction features: Furnace is lined with foil-faced high density insulation to minimize noise and heat loss. High temperature ceramic combustion chamber provides quiet combustion.
IAQ equipment supported: A permanent filter is included; it can be vacuumed and washed for reuse.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: Advanced burner control has programmable delays for “valve on” and “motor off,” with multiple features including technician pump prime mode. Two communication ports allow addition of alarm contacts and future wireless communications. Multi-speed direct drive blower assembly has handy plug-in wiring. Prewired to add a/c.
Warranty information: Limited lifetime heat exchanger; five-year other parts limited. Some limitations apply, see printed warranty on website for details. AssurancePlus® extended service agreements available.
Special installation requirements: Multi-firing rate capability requires a simple nozzle change to adjust firing rate; unit is shipped with larger firing rate. Compact enough to fit in closets, utility rooms, attics. Position furnace so pipe connection to chimney will be minimal distance with minimal fittings. Allow minimum of 24 inches in front for servicing burner.
Contact: Comfort-Aire Div. Heat Controller, 517-787-2100; www.comfort-aire.com.
eProduct 182
Model: RPHE-093G through-the-wall packaged heat pump
Footprint (inches): 10 (length) by 43 (width) by 23 (height)
Serviceability features: Unit can easily be removed from mounting bracket and front panel removed for access to components.
Technical support: Available 8 a.m.-5 p.m. Eastern weekdays, at 517-787-2100.
Technical support materials: Installation, Operation and Maintenance Manual (including wiring diagrams) and parts list are available on website or by email from customer service department
Noise-reduction features: ECM blower motor has slow ramp-up and variable speeds.
IAQ equipment supported: Operation includes dehumidification only and air filtration modes. Air conditioning mode has a fresh air system that will automatically change the room air with outdoor air. The standard filter can be washed and reused. An activated carbon filter eliminates suspended particles from the standard filter, as well as odors and particles too small to be removed by the standard filter.
Thermostat compatibility: Built-in thermostat.
Replacement parts compatibility: Does not share replacement parts with other models.
Additional features: Heat pump capacity is supplemented by electric heat with outlets on each end of cabinet. Installation can be done from inside the building — all that’s required are holes for air intake/exhaust and condensate drain. Cabinet is sleek and contemporary. Built with ECM blower motor; hot gas bypass uses electronic expansion valve for improved heating during defrost cycle. Includes wireless remote.
Warranty information: Limited one-year parts and labor; limited five-year sealed system and function parts for replacement only of defective parts; some limitations apply, see printed warranty on website for details.
Special installation requirements: Use template that comes with unit to drill holes in outer wall of building for intake/exhaust/drain. Install flexible grilles, hoses and drain from room interior. Hang unit using mounting bracket included, plug into 208/230-V, 1-60 power source. Multiple units can be connected to a data network for guest room control in hotels/motels.
Contact: Comfort-Aire Div. Heat Controller, 517-787-2100; www.comfort-aire.com.
eProduct 183
Comfortmaker
Model: SoftSound® IIX 96 gas furnace
Footprint (inches): 29 (length) by 14-25 (width) by 35 (height)
Serviceability features: Blower assembly is mounted on rails for easier, upfront installation and removal. These new gas furnaces feature large, robust one-quarter turn knobs for door installation and removal. A super-bright LED makes diagnostic flash codes easier to read. Lets technicians see most recent fault code even if power shuts off.
Technical support: Technical Service Advisor on staff at local distributors is available with technical assistance, troubleshooting. Technical training is available 24/7/365 online and at field schools held at participating distributor locations nationwide.
Technical support materials: Product information posted on-line at Comfortmaker dealer website includes product spec sheets, installation-operation manuals, and technical support/parts manuals.
Noise-reduction features: The blower motor is attached with soft-mount rubber grommets that absorb sound and vibration. Furnaces feature insulated heat exchanger and blower compartments to muffle sound and absorb vibration noise.
IAQ equipment supported: When coupled with a condensing unit and humidity-capable thermostat, mainline Comfortmaker furnaces can control relative humidity during cooling operation. These furnaces have a dehumidification function in cooling mode and can control a humidifier accessory in heating mode.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Some shared parts, some unique.
Additional features: Designed for four-way multiposition installation, 35 inches tall, and lighter weight than previous counterparts, these two-stage models feature ECM blower motors that can deliver an increase in cooling efficiency when paired with select condensing units and evaporator coils. Meets low-NOx emissions standards.
Warranty information: Five-year No Hassle Replacement limited. Lifetime heat exchanger and 10-year parts limited to original purchaser with timely registration. Limited warranty period is 20-year heat exchanger and five-year parts if not registered within 90 days of installation (see warranty certificate for details and restrictions).
Special installation requirements: None.
Contact: International Comfort Products LLC (ICP), 800-315-4370; www.gocomfortmaker.com.
eProduct 184
Model: SoftSound VT 96 heat pump
Footprint (inches): 29 (length) by 14-25 (width) by 35 (height)
Serviceability features: A super-bright LED makes diagnostic flash codes easier to read. Lets technicians see last seven fault codes even if power shuts off. Blower assembly is mounted on rails for easier, upfront installation and removal. These new gas furnaces feature large, robust one-quarter turn knobs for door installation and removal.
Technical support: Technical Service Advisor on staff at local distributors is available with technical assistance, troubleshooting. Technical training is available 24/7/365 online and at field schools held at participating distributor locations nationwide.
Technical support materials: Product information posted online at Comfortmaker dealer website includes product spec sheets, installation-operation manuals, and technical support/parts manuals.
Noise-reduction features: These new furnaces include super-quiet, variable-speed ECM motors to minimize operating sound levels. The blower motor is attached with soft-mount rubber grommets that absorb sound and vibration. Furnaces feature insulated heat exchanger and blower compartments to muffle sound and absorb vibration noise.
IAQ equipment supported: When coupled with a condensing unit and humidity-capable thermostat, mainline furnaces can control relative humidity during cooling operation. These furnaces have a dehumidification function in cooling mode and can control a humidifier accessory in heating mode.
Thermostat compatibility: Compatible with most thermostats. Communicating and self-configuring function only when used with new Comfortmaker communicating control.
Replacement parts compatibility: Some shared parts, some unique.
Additional features: Featuring self-configuring control, VT 96 furnaces are built with stainless steel primary and secondary heat exchangers. Two-stage heat and two-stage cooling compatible; furnace has ECM variable-speed blower motor; designed for four-way multiposition installation; just 35 inches tall; and lighter weight than previous counterparts. Meets low-NOx emissions standards.
Warranty information: Ten-year No Hassle Replacement limited. Lifetime heat exchanger and 10-year parts limited to original purchaser with timely registration. Limited warranty period is 20-year heat exchanger and five-year parts if not registered within 90 days of installation (see warranty certificate for details and restrictions).
Special installation requirements: None.
Contact: International Comfort Products LLC (ICP), 800-315-4370; www.gocomfortmaker.com.
eProduct 185
Concord
Model: 4HP13 split-system heat pump
Footprint (inches): 24 (length) by 24 (width) by 33 (height)
Serviceability features: Removable louvered panels to access coils. Double and single concentric knockouts for electrical connections. Ground lugs standard. Corner-mounted service valves for access. Defrost control with built-in diagnostics.
Technical support: Available at 800-515-3501 Monday-Friday, 8 a.m.-5 p.m. Eastern.
Technical support materials: Wiring diagram, troubleshooting information, installation data performance, parts and accessories documentation are available.
Noise-reduction features: Anti-vibration compressor pads and sound-reducing fan discharge top.
IAQ equipment supported: Compatible with most IAQ products.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: Robust dual-fuel offering 13-18 SEER. Compatible with various types of air handlers including wall-mount, soffit, and high velocity.
Warranty information: Ten-year compressor, 10-year parts (with registration).
Special installation requirements: None.
Contact: Allied Air Enterprises, 803-738-4000; www.alliedair.com.
eProduct 186
Model: 80G1E constant torque furnace
Footprint (inches): 28 (length) by 15-25 (width) by 33 (height)
Serviceability features: Ten fault code recall; external drain trap with clean-out port; slide-out blower; operational with heating compartment door off; access to the flame sensor and igniter with forward facing fasteners; two-piece door design for access to components.
Technical support: Available at 800-515-3501.
Technical support materials: Wiring diagrams, service/troubleshooting information, installation instructions, parts finder/look-up tools, contractonet website, spec sheets, training CDs.
Noise-reduction features: High-efficiency constant torque motor and insulated blower compartment.
IAQ equipment supported: Manufacturer did not specify.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: Constant torque motor meets 2-percent efficiency standard requirement for tax credit eligibility.
Warranty information: Ten-year parts and lifetime heat exchanger (with registration).
Special installation requirements: Manufacturer did not specify.
Contact: Allied Air Enterprises, 803-738-4000; www.alliedair.com.
eProduct 187
Daikin AC (Americas) Inc.
Model: Altherma ERLQ_BAVJU + EKHB_030BA_VJU air-water heat pump
Footprint (inches): Twelve (length) by 32 (width) by 29 (height)
Serviceability features: Self-diagnostics for simple error code retrieval, Dr. Daikin error code assistance, fully configurable field settings to optimize system operation to suit customer needs.
Technical support: Available at 866-432-4546, 7 a.m. and 6 p.m. Central.
Technical support materials: Full suite of installation and service manuals, maintenance guides, spare parts documentation, and dealer support handbooks. “Dr. Daikin” error code support via Smart Phone, SMS Text Message, or web (www.drdaikin.com).
Noise-reduction features: Low-noise components including compressor, fan, and fan motor for nominal sound levels of 48 dBa. Fully optimized and insulated indoor located hydrobox for nominal sound levels as low as 30 dBa.
IAQ equipment supported: Altherma can be utilized for radiant underfloor heating applications, reducing filtration requirements and air movement in the home for optimum comfort. If fan coil units are selected, they come with MERV-8 filters standard.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: An innovative and highly efficient solution serving heating, cooling, and domestic hot water requirements in a home or apartment. Very flexible applications are possible with the ability to serve multiple zones and different heat emitter solutions (floor, wall, ceiling, etc.). Enhanced energy savings and near net zero capable with solar thermal connection, as well as a strong integration to grid-tied solar PV installations.
Warranty information: Standard one-year limited later, five-year parts, seven-year compressor. Extended warranty program also available.
Special installation requirements: R-410A certification; factory training; knowledge of hydronics design and installation; plumbing license normally required. For installation, verification of water side design important to confirm water volume, flow, and pressure drop are within system limitations.
Contact: Daikin AC (Americas) Inc., 972-245-1510; www.daikinac.com.
eProduct 188
Day & Night
Model: Constant Comfort™ IIX 96 gas furnace
Footprint (inches): 29 (length) by 14-25 (width) by 35 (height)
Serviceability features: Blower assembly is mounted on rails for upfront installation and removal. These gas furnaces feature large, robust one-quarter turn knobs for door installation and removal. A super-bright LED makes diagnostic flash codes easier to read. Lets technicians see most recent fault code even if power shuts off.
Technical support: Technical Service Advisor on staff at local distributors is available with technical assistance, troubleshooting. Technical training is available 24/7/365 online and at field schools held at participating distributor locations nationwide.
Technical support materials: Product information posted online at Day & Night dealer website includes product spec sheets, installation-operation manuals, and technical support/parts manuals.
Noise-reduction features: The blower motor is attached with soft-mount rubber grommets that absorb sound and vibration. Furnaces feature insulated heat exchanger and blower compartments to muffle sound and absorb vibration noise.
IAQ equipment supported: When coupled with a condensing unit and humidity-capable thermostat, mainline Day & Night furnaces can control relative humidity during cooling operation. These furnaces have a dehumidification function in cooling mode and can control a humidifier accessory in heating mode.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Some shared parts, some unique.
Additional features: Designed for four-way multiposition installation, just 35 inches tall, and lighter weight than previous counterparts, these two-stage models feature ECM blower motors that can deliver an increase in cooling efficiency when paired with select condensing units and evaporator coils. Meets low-NOx emissions standards.
Warranty information: Five-year No Hassle Replacement™ limited warranty. Lifetime heat exchanger, 10-year parts limited to original purchaser with timely registration. Limited warranty period is 20-year heat exchanger and five-year parts if not registered within 90 days of installation (see warranty certificate for details and restrictions).
Special installation requirements: None.
Contact: International Comfort Products, LLC (ICP), 800-315-4370; www.godayandnight.com.
eProduct 189
Model: Constant Comfort™ VC 97 gas furnace
Footprint (inches): 29 (length) by 18-25 (width) by 35 (height)
Serviceability features: These new furnaces feature large, one-quarter turn knobs for door installation and removal. A super-bright LED makes diagnostic flash codes easier to read. Blower assembly is mounted on rails for upfront installation and removal. Lets technicians see last seven fault codes even if power shuts off.
Technical support: Technical Service Advisor on staff at local distributors is available with technical assistance, troubleshooting. Technical training is available 24/7/365 online and at field schools held at participating distributor locations nationwide.
Technical support materials: Product information posted online at Day & Night dealer website includes product spec sheets, installation-operation manuals, and technical support/parts manuals.
Noise-reduction features: Variable-speed ECM blower motor reduces operating sound levels. Special blower mount quiets vibration and cuts sound. Cabinet insulation absorbs sound from heat exchanger and blower compartments.
IAQ equipment supported: When coupled with a condensing unit and humidity-capable thermostat, mainline Day & Night furnaces can control relative humidity during cooling operation. These furnaces have a dehumidification function in cooling mode and can control a humidifier accessory in heating mode.
Thermostat compatibility: Requires a special thermostat. For self-configuring control to function, must use with Day & Night communicating control (thermostat).
Replacement parts compatibility: Some shared parts, some unique.
Additional features: Featuring self-configuring control, these furnaces are built with stainless steel primary and secondary heat exchangers. Modulating (multistage) gas valves allow furnaces to operate on a quieter low-fire setting unless thermostat calls for more fire. Designed for four-way multiposition installation, just 35 inches tall, and lighter weight than previous counterparts.
Warranty information: Ten-year No Hassle Replacement™ limited warranty. Lifetime heat exchanger and 10-year parts limited to original purchaser with timely registration. Limited warranty period is 20-year heat exchanger and five-year parts if not registered within 90 days of installation (see warranty certificate for details and restrictions).
Special installation requirements: None.
Contact: International Comfort Products, LLC (ICP), 800-315-4370; www.godayandnight.com.
eProduct 190
Ducane
Model: 4HP13 split system heat pump
Footprint (inches): 24 (length) by 24 (width) by 33 (height)
Serviceability features: Removable louvered panels to access coils. Double and single concentric knockouts for electrical connections. Ground lugs standard. Corner-mounted service valves for access. Defrost control with built-in diagnostics.
Technical support: Available at 800-515-3501 Monday-Friday, 8 a.m.-5 p.m. Eastern.
Technical support materials: Wiring diagram, troubleshooting information, installation data performance, parts and accessories documentation are available.
Noise-reduction features: Anti-vibration compressor pads and sound-reducing fan discharge top.
IAQ equipment supported: Compatible with most IAQ products.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: Robust dual fuel offering 13-18 SEER. Compatible with various types of air handlers including wall-mount, soffit, and high velocity.
Warranty information: Ten-year compressor, 10-year parts (with registration).
Special installation requirements: None.
Contact: Allied Air Enterprises, 803-738-4000; www.alliedair.com.
eProduct 191
Model: 95G1E constant torque furnace
Footprint (inches): 28 (length) by 18-25 (width) by 33 (height)
Serviceability features: Ten fault code recall; external drain trap with clean-out port; slide-out blower; operational with heating compartment door off; access to the flame sensor and igniter with forward facing-fasteners; two-piece door design for access to components.
Technical support: Available at 800-515-3501.
Technical support materials: Wiring diagrams, service/troubleshooting information, installation instructions, parts finder/look-up tools, contractornet website, spec sheets, training CDs.
Noise-reduction features: High-efficiency constant-torque motor and insulated blower compartment.
IAQ equipment supported: Manufacturer did not specify.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: Constant torque motor meets 2-percent efficiency standard requirement for tax credit eligibility.
Warranty information: Ten-year parts and lifetime heat exchanger (with registration).
Special installation requirements: Manufacturer did not specify.
Contact: Allied Air Enterprises, 803-738-4000; www.alliedair.com.
eProduct 192
Dunkirk Boilers
Model: Helix VLT modulating condensing boiler
Footprint (inches): 20 (length) by 14 (width) by 31 (height)
Serviceability features: Features an innovative 316L/444 stainless steel fin tube heat exchanger, built-in primary/secondary piping, factory-installed probe-type, low water cut-off, corrosion-resistant CPVC flue collector, control with text display, outdoor reset, priority domestic hot water, and integrated multiple boiler control capability (up to 16 boilers).
Technical support: Available Monday-Friday, 7:30 a.m.-5 p.m. Eastern at 800-325-5479.
Technical support materials: Color brochure, gas conversion instructions, parts list, user’s manual, manufacturer’s warranty, additional warranty.
Noise-reduction features: Sealed housing reduces noise for quiet comfort in any living space.
IAQ equipment supported: Manufacturer did not specify.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Some shared parts, some unique.
Additional features: Vertical Laser Tube (VLT) condensing boiler features a revolutionary, vertically mounted, helical fin tube heat exchanger, made of 316L/444 stainless steel. This self-cleaning design features wide, smooth waterways that help remove hard water deposits and prevent scaling.
Warranty information: Fifteen-year limited heat exchanger. Availability of optional Comfort Plus Parts and Labor extended warranties ensure peace of mind.
Special installation requirements: Replacement ready with 1 ¼-in. piping connections and low pressure drop — no high-head pump required. Simplified electrical connections with removable terminal block. Jacket slides on and off for quick access. Wall mount bracket included.
Contact: Dunkirk Boilers, 315-797-1310; www.dunkirk.com.
eProduct 193
EarthLinked Technologies
Model: SC, SW, and SD direct geoexchange split system heat pump
Footprint (inches): 24 (length) by 28 (width) by 25 (height)
Serviceability features: Adaptiv™ refrigerant flow controls make system charging simple. Service valves provided to isolate earth loops from compressor unit. SW model includes on-demand domestic water preheating. SD model has internally mounted desuperheater that is pre-plumbed and prewired to reduce installation time.
Technical support: Available 8 a.m.-5 p.m. Eastern. Authorized dealers have access to after-hours phone support.
Technical support materials: Application and system selection, installation, and service manuals available on website and hard copy.
Noise-reduction features: Fully insulated cabinet, no outdoor fan.
IAQ equipment supported: Manufacturer did not specify.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: Uses highly conductive copper loops to transfer renewable energy from the earth, eliminating the indirect transfer medium found in water loop geo systems.
Warranty information: Five-year compressor and all major components. Twenty-year earth loops.
Special installation requirements: Sold only through authorized, factory-trained installers.
Contact: EarthLinked Technologies, 863-701-0096; www.earthlinked.com.
eProduct 194
Friedrich Air Conditioning
Model: PDH12K packaged terminal heat pump
Footprint (inches): 14 (length) by 42 (width) by 16 (height)
Serviceability features: Modular product design ensures access to key components for cleaning and repairs. Service error code memory facilitates improved unit diagnostics. Universal heater with heat capacity determined by power and selection. Power cords change as easily as plugging in a phone jack. Reversible indoor air louver. Faultless, sure-hold front cover system attaches securely each time.
Technical support: Available Monday-Friday, 8 a.m.-5 p.m. Central at 877-599-5665.
Technical support materials: Product profile, service manual, parts manual, installation-operation guide, and wiring diagrams.
Noise-reduction features: Two-motor design allows the indoor motor to run at quieter, lower speeds. Tangential blower wheel with five times the surface area of a traditional PTAC fan creates a wide air path that moves more air quietly. Quiet, efficient rotary compressor is mounted with vibration-isolators to keep the compressor running smoothly and quietly. High-density insulation blanket blocks outside noise.
IAQ equipment supported: Fresh air damper control to bring in fresh air as desired. Two washable, interchangeable antimicrobial air filters.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: PTAC has comfort, durability, maintenance and installation, energy management, and IAQ features that deliver quieter performance with improved airflow and higher energy efficiency. It’s a problem solver with a full line of accessories that include traditional drain kits, subbases and louvers to lateral duct adapters and duct extensions for ducted airflow.
Warranty information: Five-year sealed system. Limitations apply.
Special installation requirements: Manufacturer did not specify.
Contact: Friedrich Air Conditioning, 210-546-0500; www.friedrich.com.
eProduct 195
Frigidaire
Model: FG7SD/M gas furnace
Footprint (inches): 28 (length) by 14-25 (width) by 35 (height)
Serviceability features: Low height makes this furnace easier to apply in low-ceiling applications and works well with taller, high-SEER coils. Diagnostic lights provide troubleshooting without counting flashes. A color-coded wire harness is designed for service and replacement.
Technical support: Available at 800-422-4328 Monday-Friday, 8 a.m.-4:30 p.m. Central. Technical literature via dealer log-in website and www.nordyneu.com
Technical support materials: Wiring diagrams, replacement parts lists, installation instructions.
Noise-reduction features: Sealed and insulated blower compartment and sealed vestibule.
IAQ equipment supported: Integrated control board with connections for electronic air cleaner and humidifier.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: All furnaces are 100-percent fired and tested on the manufacturing line. Includes packaging with a corner post design to ensure that the product arrives damage-free.
Warranty information: With product registration, 10-year all parts, and 10-year Quality Pledge to replace entire unit if the heat exchanger fails.
Special installation requirements: Manufacturer did not specify.
Contact: Nordyne, 636-561-7300; www.frigidaire.net.
eProduct 196
Model: Q5RF packaged heat pump
Footprint (inches): 49 (length) by 35 (width) by 30-38 (height)
Serviceability features: High- and low-pressure controls and high/low service ports allow quick access without disrupting operation; liquid line filter-driers; crankcase heater provides protection from liquid floodback. Designed to make servicing easier with access panels provided to the compressor and access to evaporator coil for cleaning and general maintenance.
Technical support: Available at 800-422-4328 Monday-Friday, 8 a.m.-4:30 p.m. Technical literature and training videos are available on dealer log-in site and www.nordyneu.com
Technical support materials: Wiring diagrams, replacement parts lists, installation instructions.
Noise-reduction features: Compressor sound blanket. Energy- efficient brushless DC (ECM) blower motor.
IAQ equipment supported: State-of-the-art Copeland Ultra-Tech Scroll compressor provides two-stage heat/cool for temperature control.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: Protected distributor tubes, both indoor and outdoor coils include very high-abrasion-resistance fiberglass sleeves to prevent leaks from tubing rubbing together. A wire guard coated with epoxy and mesh hail guard protect the coil from being damaged by balls, lawnmowers, hail, etc.
Warranty information: Ten-year all parts and 10-year Quality Pledge to replace the entire unit if its compressor fails within the first 10 years of operation to the original owner. Consumer product registration required within a limited period after installation.
Special installation requirements: Zero-inch clearance to combustibles on duct side of the unit, allowing for installation in tight areas.
Contact: Nordyne, 636-561-7300; www.frigidaire.net.
eProduct 197
Fujitsu General America, Inc.
Model: Halcyon HFI Single Zone System (12RLFW) mini-split heat pump
Footprint (inches): Indoor unit 8 (length) by 31 (width) by 11 (height); outdoor unit 12 (length) by 31 (width) by 21 (height)
Serviceability features: LED lights up when the unit needs to be cleaned. This occurs after about 400 hours of use.
Technical support: Available at 866-952-8324, 8 a.m.-8 p.m. Eastern.
Technical support materials: Operation manual, installation manual, service manual, troubleshooting guides, quick installation guide, and detailed specs available on contractor website.
Noise-reduction features: Indoor unit goes down to 25 dB in Quiet Mode in both heating and cooling; outdoor unit is 49 dB.
IAQ equipment supported: Manufacturer did not specify.
Thermostat compatibility: Requires special thermostat.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: Energy Star qualified, federal tax credit qualified, uses R-410A, wireless remote control, optional wired remote controller, 24-hour timer, dry mode, auto restart/reset, low ambient.
Warranty information: Five-year parts, seven-year compressor.
Special installation requirements: Manufacturer did not specify.
Contact: Fujitsu General America, Inc., 973-575-0380; www.fujitsugeneral.com.
eProduct 198
Model: Halcyon HFI Flex Zone (AOU48RLXFZ) multisplit system
Footprint (inches): 15 (length) by 38 (width) by 36 (height)
Serviceability features: Outdoor unit includes a self-diagnostic feature. The printed circuit board provides three modes of diagnostics, setting, monitoring, and function mode, as well as error codes. It also provides a precommissioning check function.
Technical support: Available at 866-952-8324, 8 a.m.- 8 p.m. Eastern.
Technical support materials: Operation manual, installation manual, service manual, troubleshooting guides, quick installation guide, and detailed specs available on website.
Noise-reduction features: Manufacturer did not specify.
IAQ equipment supported: Manufacturer did not specify.
Thermostat compatibility: Requires special thermostat.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: Outdoor unit (AOU48RLXFZ) allows up to eight indoor units to be connected to it. Choose from three different indoor unit styles — wall mounted, cassette, or slim duct. This unit provides year-round whole-home or business heating and cooling in most climates.
Warranty information: Five-year parts, seven-year compressor.
Special installation requirements: Branch box(es) and separation tube assemblies required.
Contact: Fujitsu General America, Inc., 973-287-1646; www.fujitsugeneral.com.
eProduct 199
GeoComfort
Model: Compass Series GCT combination vertical packaged geothermal water-air unit
Footprint (inches): 32 (length) by 30 (width) by 56-60 (height)
Serviceability features: Eye-level mounted controls with individual LED fault lights. Full 360-degree access to all components. Five compressor section access panels and three blower section access panels.
Technical support: Available 24 hours.
Technical support materials: Wiring diagrams, full documentation, parts list, service and troubleshooting guidance.
Noise-reduction features: Quadruple compressor isolation, gasketed access panels, heavy closed-cell foam insulation.
IAQ equipment supported: E-coated air coils. Composite drain pan with silver ion antimicrobial protection built in. Pleated air filters. Compatible with most IAQ products.
Thermostat compatibility: Requires a special thermostat (heat pump thermostat and aquastat).
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: The multipositional combination geothermal heat pump provides forced-air heating and cooling, as well as hydronic heating for radiant floors and other applications. All models in the GCT Series meet Energy Star Tier 3 performance ratings.
Warranty information: Five-year labor, five-year all parts, five-year refrigerant circuit, 10-year compressor. Optional 10-year labor, 10-year all parts, 10-year refrigerant circuit. Optional lifetime compressor.
Special installation requirements: Manufacturer did not specify.
Contact: Enertech Manufacturing, LLC, 618-664-9010; www.enertechmfg.com.
eProduct 200
Model: Compass Series GHT horizontal packaged geothermal water-air unit
Footprint (inches): 54-68 (length) by 26-30 (width) by 22-24 (height)
Serviceability features: Three compressor section access panels and two blower section access panels. Individual fault LED lights on the control board. Access to all components throughout the cabinet.
Technical support: Available 24 hours.
Technical support materials: Wiring diagrams, full documentation, parts list, service and troubleshooting guidance.
Noise-reduction features: Fully insulated cabinet with gasketed access panels to eliminate panel rattle. Isolated compressor and blower mounting.
IAQ equipment supported: Recycled, foil face, blue-jean insulation. E-coated air coils. Stainless steel drain pans.
Thermostat compatibility: Requires a heat pump thermostat.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: Features a highly ridged cabinet with all models meeting Energy Star Tier 3 ratings.
Warranty information: Five-year labor, five-year all parts, five-year refrigerant circuit, 10-year compressor. Optional 10-year labor, 10-year all parts, 10-year refrigerant circuit. Optional lifetime compressor.
Special installation requirements: Manufacturer did not specify.
Contact: Enertech Manufacturing, LLC, 618-664-9010; www.enertechmfg.com.
eProduct 201
GeoSystems
Model: HydroHeat Mega-Tek geothermal heat pump
Footprint (inches): 28 (length) by 32 (width) by 65 (height)
Serviceability features: Designed for ease of service, features seven panels for access to components. Six status lights on the front of the unit provide service diagnostics. An optional hand-held service tool displays refrigerant and loop temperatures, lockouts and run hours, simplify calculating superheat and subcooling, and allow for overriding the thermostat during service.
Technical support: Dealer support line available at 800-418-8324 Monday-Friday, 8:30 a.m.-5:30 p.m. Eastern.
Technical support materials: Installation manuals, engineering data, and technical bulletins can be downloaded.
Noise-reduction features: Uses two-stage scroll compressors. The cabinet and base are designed to reduce the transmission of vibration. Cabinets are fully insulated.
IAQ equipment supported: Two-stage compressor provides for longer run times and better dehumidification. The dehumidification can be increased by attaching an external humidistat to slow the variable-speed blower when indoor humidity is high.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: Seven temperature sensors monitor the refrigeration circuit, ground loop, and domestic hot water circuit for control and lock-out protection. Offers domestic hot water production to provide all of a typical household’s potable hot water needs. Interfaces with hand-held digital diagnostic tool for commissioning and troubleshooting.
Warranty information: Standard five-year parts and labor. Extended warranty available for 10-year parts and labor.
Special installation requirements: Manufacturer did not specify.
Contact: GeoSystems, LLC, 763-582-1400; geosystemsghp.com.
eProduct 202
Gibson
Model: KG7SD/M gas furnace
Footprint (inches): 28 (length) by 14-25 (width) by 35 (height)
Serviceability features: Low height makes this furnace easier to apply in low-ceiling applications and works well with taller, high-SEER coils. Diagnostic lights provide troubleshooting without counting flashes. A color-coded wire harness is designed for service and replacement.
Technical support: Available at 800-422-4328 Monday-Friday, 8 a.m.-4:30 p.m. Central. Technical literature via www.
nordyneu.com.
Technical support materials: Wiring diagrams, replacement parts lists, installation instructions.
Noise-reduction features: Sealed and insulated blower compartment and sealed vestibule.
IAQ equipment supported: Integrated control board with connections for electronic air cleaner and humidifier.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: All furnaces are 100-percent fired and tested on the manufacturing line. Includes packaging with a corner post design to ensure that the product arrives damage-free.
Warranty information: With product registration, 10-year all parts, and one-year Quality Pledge to replace entire unit if the heat exchanger fails.
Special installation requirements: Manufacturer did not specify.
Contact: Nordyne, 636-561-7300; www.gibsonhvac.com.
eProduct 203
Goodman
Model: DSZC18 heat pump
Footprint (inches): 35 (length) by 35 (width) by 38 (height)
Serviceability features: Expanded ComfortAlert diagnostics are built in. As part of a ComfortNet communicating control system, the unit is set-up capable with two low-voltage wires. Diagnostic indicator lights and storage of six fault codes. Single-panel access to controls with space provided for field-installed accessories. Top and side maintenance access. Sweat connection service valves with access to gauge ports.
Technical support: Available through local distributors and factory direct at 888-593-9988.
Technical support materials: All technical materials may be downloaded from the brand website and PartnerLink.
Noise-reduction features: High-density foam compressor sound blanket. SmartShift™ technology with short-cycle protection to ensure reliable defrost cycles. Factory-installed high-capacity sound muffler. Sound-control top panel design. Quiet ECM-style condenser fan motor.
IAQ equipment supported: Fully supports all IAQ components and accessories.
Thermostat compatibility: Compatible with most thermostats; requires a special thermostat.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: Standard, factory-installed components include SmartShift defrost technology, bi-flow liquid line filter, suction line accumulator, crankcase heater band, high-capacity sound muffler, coil and ambient temperature sensors, high- and low-pressure switches. Unit is ComfortNet communications system compatible.
Warranty information: Ten-year unit replacement limited warranty, lifetime compressor limited, 10-year parts limited.
Special installation requirements: Compact footprint makes installation easier than larger units.
Contact: Goodman Global Group, Inc., 713-861-2500; www.goodmanmfg.com.
eProduct 204
Model: GMVM96 modulating gas furnace
Footprint (inches): 17 (length) by 28 (width) by 40 (height)
Serviceability features: Furnace control board with self-diagnostics and color-coded low-voltage terminals. When installed as part of a ComfortNet communicating control system, additional service features are available via the user interface.
Technical support: Available through local distributors and the factory at 800-593-9988.
Technical support materials: Available through local distributors. Materials can be downloaded from the brand website and via PartnerLink.
Noise-reduction features: Fully insulated heavy-gauge steel cabinet. Foil-faced insulation lines the heat exchanger section. Efficient and quiet variable-speed circulator motor ramps up or down according to heating or cooling demand.
IAQ equipment supported: Compatible with a variety of all IAQ components, including filters, humidifiers, etc. The furnace control board has provisions for electronic air cleaners’ and humidifiers’ electrical connections.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: Aluminized-steel, dual-diameter tubular heat exchanger coupled with a stainless steel secondary heat exchanger. When installed as part of a ComfortNet communicating control system, the unit offers ease of installation. The self-calibrating, modulating gas valve offers performance 35-100 percent of capacity.
Warranty information: Ten-year unit replacement limited warranty, lifetime heat exchanger limited, 10-year parts limited.
Special installation requirements: Left or right connections for gas and electric service. Designed for multiposition installation: upflow, horizontal left or right. With an airtight solid bottom for side-return applications and easier-cut tabs provide easier removal in bottom air-inlet applications.
Contact: Goodman Global Group, Inc., 713-861-2500; www.goodmanmfg.com.
eProduct 205
Heil
Model: QuietComfort® DLX 96 gas furnace
Footprint (inches): 29 (length) by 14-25 (width) by 35 (height)
Serviceability features: Sturdy knobs allow service techs to remove and replace furnace doors. A bright LED makes diagnostic flash codes easier to read. Blower assembly is mounted on rails for upfront installation and removal. Lets technicians see latest fault code even if power shuts off.
Technical support: Technical Service Advisor on staff at local distributors is available with technical assistance, troubleshooting. Technical training is available 24/7/365 online and at field schools held at participating distributor locations nationwide.
Technical support materials: Product information posted online at dealer website includes product spec sheets, installation-operation manuals, and technical support/parts manuals.
Noise-reduction features: The blower motor of the new 96-percent furnaces is attached with soft-mount rubber grommets that absorb sound and vibration. Furnaces feature insulated heat exchanger and blower compartments to muffle sound and absorb vibration noise.
IAQ equipment supported: When coupled with a condensing unit and humidity-capable thermostat, mainline Heil furnaces can control relative humidity during cooling operations. These furnaces have a dehumidification function in cooling mode and can control a humidifier accessory in heating mode.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Some shared parts, some unique.
Additional features: Designed for four-way multiposition installation, 35 inches tall, and lighter weight than previous counterparts. ECM blower motors can deliver an increase in cooling efficiency when paired with select condensing units and evaporator coils. Meets low-NOx emissions standards.
Warranty information: One-year No Hassle Replacement™ limited warranty. Lifetime heat exchanger and 10-year parts limited to original purchaser with timely registration. Limited warranty period is 20-year heat exchanger and five-year parts if not registered within 90 days of installation (see warranty certificate for details and restrictions).
Special installation requirements: None.
Contact: International Comfort Products, LLC (ICP), 800-315-4370; www.goheil.com.
eProduct 206
Model: QuietComfort® VT 96 gas furnace
Footprint (inches): 29 (length) by 14-25 (width) by 35 (height)
Serviceability features: A bright LED makes diagnostic flash codes easier to read. Lets technicians see last seven fault codes even if power shuts off. Blower assembly is mounted on rails for upfront installation and removal. These new furnaces feature large, robust, one-quarter turn knobs for door installation and removal.
Technical support: Technical Service Advisor on staff at local distributors available with technical assistance, troubleshooting. Technical training is available 24/7/365 online and at field schools held at participating distributor locations nationwide.
Technical support materials: Product information posted online at dealer website includes product spec sheets, installation-operation manuals, and technical support-parts manuals.
Noise-reduction features: Variable-speed ECMs minimize operating sound levels. The blower motor is attached with soft-mount rubber grommets that absorb sound and vibration. Insulated heat exchanger and blower compartments muffle sound and absorb vibration noise.
IAQ equipment supported: When coupled with a condensing unit and humidity-capable thermostat, mainline Heil furnaces can control relative humidity during cooling operation. These furnaces have a dehumidification function in cooling mode and can control a humidifier accessory in heating mode.
Thermostat compatibility: Compatible with most thermostats. Communicating and self-configuring function only when used with new Heil communicating control (thermostat).
Replacement parts compatibility: Some shared parts, some unique.
Additional features: Featuring self-configuring control, furnaces are built with stainless steel primary and secondary heat exchangers. Two-stage heat and two-stage cooling compatible, furnace has ECM variable-speed blower motor, is designed for four-way multiposition installation, 35 inches tall, and lighter weight than previous counterparts. Meets low-NOx emissions standards.
Warranty information: Ten-year No Hassle Replacement™ limited warranty. Lifetime heat exchanger and 10-year parts limited to original purchaser with timely registration. Limited warranty period is 20-year heat exchanger and five-year parts if not registered within 90 days of installation (see warranty certificate for details and restrictions).
Special installation requirements: None.
Contact: International Comfort Products, LLC (ICP), 800-315-4370; www.goheil.com.
eProduct 207
Hydron Module
Model: Revolution Series HCT combination vertical packaged geothermal water-air unit
Footprint (inches): 32 (length) by 30 (width) by 56-60 (height)
Serviceability features: Eye-level mounted controls with individual LED fault lights. Full 360-degree access to all components. Five compressor section access panels and three blower section access panels.
Technical support: Available 24 hours.
Technical support materials: Wiring diagrams, full documentation, parts list, service and troubleshooting guidance.
Noise-reduction features: Quadruple compressor isolation, gasketed access panels, heavy closed-cell foam insulation.
IAQ equipment supported: E-coated air coils. Composite drain pan with silver-ion antimicrobial protection built in. Pleated air filters. Compatible with most IAQ products.
Thermostat compatibility: Requires a special thermostat (heat pump thermostat and aquastat).
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: The first multipositional combination geothermal heat pump in the industry provides forced-air heating and cooling, as well as hydronic heating for radiant floors and other applications. All models in the series meet Energy Star Tier 3 performance ratings.
Warranty information: Ten-year labor, 10-year all parts, 10-year refrigerant circuit, lifetime compressor, lifetime cabinet, lifetime coaxial heat exchanger. Optional 5/5/5 deduct with lifetime compressor, lifetime cabinet, lifetime coaxial heat exchanger.
Special installation requirements: Manufacturer did not specify.
Contact: Enertech Manufacturing, LLC, 618-664-9010; www.enertechmfg.com.
eProduct 208
Model: Revolution Series HHT horizontal packaged geothermal water-air unit
Footprint (inches): 54-68 (length) by 26-30 (width) by 22-24 (height)
Serviceability features: Three compressor section access panels and two blower section access panels. Individual fault LED lights on the control board. Access to all components throughout the cabinet.
Technical support: Available 24 hours.
Technical support materials: Wiring diagrams, full documentation, parts list, service and troubleshooting guidance.
Noise-reduction features: Fully insulated cabinet with gasketed access panels to eliminate panel rattle. Isolated compressor and blower mounting.
IAQ equipment supported: Recycled, foil-face, blue-jean insulation. E-coated air coils. Stainless steel drain pans.
Thermostat compatibility: Requires a special thermostat (heat pump thermostat).
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: Features a highly ridged cabinet with all models meeting Energy Star Tier 3 ratings.
Warranty information: Ten-year labor, 10-year all parts, 10-year refrigerant circuit, lifetime compressor, lifetime cabinet, lifetime coaxial heat exchanger. Optional 5/5/5 deduct with lifetime compressor, lifetime cabinet, lifetime coaxial heat exchanger.
Special installation requirements: Manufacturer did not specify.
Contact: Enertech Manufacturing, LLC, 618-664-9010; www.enertechmfg.com.
eProduct 209
Intertherm
Model: CMF95 gas furnace
Footprint (inches): 24 (length) by 18 (width) by 57 (height)
Serviceability features: Dedicated flame sensor light and two lights in combination to indicate fault codes without counting flashes.
Technical support: Available at 800-422-4328 Monday-Friday, 8 a.m.-4:30 p.m. Central. Technical literature via www.nordyneu.com.
Technical support materials: Wiring diagrams, replacement parts lists, installation instructions.
Noise-reduction features: Manufacturer did not specify.
IAQ equipment supported: Manufacturer did not specify.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: Furnace in classic 18-inch width for tight replacement jobs.
Warranty information: With registration, five-year parts, one-year labor.
Special installation requirements: Manufacturer did not specify.
Contact: Nordyne, 636-561-7300; www.intertherm.net.
eProduct 210
Model: M7 gas furnace
Footprint (inches): 25 (length) by 20 (width) by 56 (height)
Serviceability features: Easy-open pawl latch secures the door firmly for transit, allows removal for access.
Technical support: Available at 800-422-4328 Monday-Friday, 8 a.m.-4:30 p.m. Central. Technical literature via www.
nordyneu.com.
Technical support materials: Wiring diagrams, replacement parts lists, installation instructions.
Noise-reduction features: Quiet operation through in-shot burners, inducer location, and cabinet insulation.
IAQ equipment supported: Manufacturer did not specify.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: All furnaces are 100-percent fired and tested on the manufacturing line. This 95 percent AFUE furnace to fit a standard manufactured housing footprint.
Warranty information: With product registration, five-year all parts and one-year labor.
Special installation requirements: Manufacturer did not specify.
Contact: Nordyne, 636-561-7300; www.intertherm.net.
eProduct 211
Kelvinator
Model: KG7SD/M gas furnace
Footprint (inches): 28 (length) by 14-25 (width) by 35 (height)
Serviceability features: Low height makes this furnace easier to apply in low-ceiling applications and works well with taller, high-SEER coils. Diagnostic lights pro-
vide troubleshooting without counting flashes. A color-coded wire harness is designed for ease of service and replacement.
Technical support: Available at 800-422-4328 Monday-Friday, 8 a.m.-4:30 p.m. Central. Technical literature via www.nordyneu.com.
Technical support materials: Wiring diagrams, replacement parts lists, installation instructions.
Noise-reduction features: Sealed and insulated blower compartment and sealed vestibule.
IAQ equipment supported: Integrated control board with connections for electronic air cleaner and humidifier.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: All furnaces are 100 percent fired and tested on the manufacturing line. Includes packaging with a corner post design to ensure that the product arrives damage-free.
Warranty information: With product registration, 10-year all parts and one-year Quality Pledge to replace entire unit if the heat exchanger fails.
Special installation requirements: Manufacturer did not specify.
Contact: Nordyne, 561-636-7300; www.kelvinatorhvac.com.
eProduct 212
Laars
Model: Mascot II combination boiler and water heater
Footprint (inches): 16 (length) by 17 (width) by 31 (height)
Serviceability features: All internal components are reached through front access panels. A lower panel allows access to gas valve while the system controls remain accessible to aid with quick setup. Venting connections come out of the top and water connections from the bottom, resulting in cleaner installations.
Technical support: Available at 800-900-9276, 8 a.m.-5 p.m. Eastern.
Technical support materials: Installation manuals with parts listing and wiring diagrams come with each boiler. Revit files available online.
Noise-reduction features: Manufacturer did not specify.
IAQ equipment supported: Very low 10-ppm NOx emissions and Energy Star rated.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Some shared parts, some unique.
Additional features: Startup is made easier with a generous list of built-in components such as a 26-gallon expansion tank, three-speed circulator, variable-speed blower, and a primeless condensate trap. Combine the included components with the gas valve and controls accessibility and the Mascot II is an easier system to set up.
Warranty information: Twelve-year limited (visit website for details).
Special installation requirements: Manufacturer did not specify.
Contact: Laars Heating Systems, 603-335-6300; www.laars.com.
eProduct 213
Lennox
Model: Elite EL195E constant torque furnace
Footprint (inches): 29 (length) by 18-25 (width) by 33 (height)
Serviceability features: Tool-free latches on blower and burner doors; gas piping and electrical service inlets on both cabinet sides; a safety interlock switch that automatically shuts off power to the unit when the blower compartment access door is removed; and a removable blower and burner assembly allows for quick servicing.
Technical support: Technical documents available online, or by calling 800-953-6669.
Technical support materials: Engineering handbook, installation-operation manual, service manual available online.
Noise-reduction features: A fully insulated cabinet with foil-faced insulation on the sides and back of the heating compartment for quiet, efficient operation. A secondary heat exchanger captures additional heat.
IAQ equipment supported: Low-speed fan slowly circulates a consistent, continuous flow of air. It also increases the effectiveness of the system’s filters, allowing them to capture and remove more pollutants from indoor air. Add-on indoor coils, high-efficiency air cleaners, and humidifiers can easily be integrated for enhanced air quality.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: Power Saver technology uses a constant-torque motor to increase efficiency through quiet and continual operation. A low-profile cabinet allows upflow or horizontal installation. A patented ArmorTuf™, aluminized steel Duralok Plus® heat exchanger, Lennox burner box design, SureLight® igniter, and control board for long product life and reliability.
Warranty information: Limited lifetime heat exchanger and five-year limited on all remaining covered components.
Special installation requirements: In the U.S., flue sizing must conform to the methods outlined in the current National Fuel Gas Code (NFPA 54/ANSI−Z223.1) or applicable provisions of local building codes. In Canada, flue sizing must conform to the methods outlined in National Standard of Canada CAN/CSA−B149.1.
Contact: Lennox Industries, 972-497-7311; www.lennox.com.
eProduct 214
Model: Merit ML180E constant torque furnace
Footprint (inches): 30 (length) by 18-25 (width) by 33 (height)
Serviceability features: Tool-free latches on blower and burner doors; gas piping and electrical service inlets on both cabinet sides; a safety interlock switch that automatically shuts off power to the unit when the blower compartment access door is removed; and a removable blower and burner assembly allows for quick servicing.
Technical support: Available online or by calling 800-953-6669 Monday-Friday, 8 a.m.-8 p.m. Eastern.
Technical support materials: Engineering handbook, installation-operation manual, service manual available online.
Noise-reduction features: A fully insulated cabinet with foil-faced insulation on the sides and back of the heating compartment ensures quieter, efficient operation. A secondary heat exchanger captures additional heat.
IAQ equipment supported: Low-speed fan slowly circulates a consistent, continuous flow of air. It also increases the effectiveness of the system’s filters, allowing them to capture and remove more pollutants from indoor air. Add-on indoor coils, high-efficiency air cleaners, and humidifiers can be integrated for enhanced air quality.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: Power Saver technology’s constant-torque motor increases system efficiency through quiet and continual operation. A low-profile cabinet allows upflow or horizontal installation. ArmorTuf aluminized steel Duralok Plus heat exchanger, Lennox burner box design, SureLight igniter, and control board offer longer product life and reliability.
Warranty information: Twenty-year limited heat exchanger, five-year limited on covered parts.
Special installation requirements: In the U.S., flue sizing must conform to the methods outlined in the current National Fuel Gas Code (NFPA 54/ANSI−Z223.1) or applicable provisions of local building codes. In Canada, flue sizing must conform to the methods outlined in National Standard of Canada CAN/CSA−B149.1.
Contact: Lennox Industries, 972-497-7311; www.lennox.com.
eProduct 215
LG Electronics USA
Model: LG Art Cool Picture (LA096HNP/LA126HNP) single-zone mini-split
Footprint (inches): 6 (length) by 24 (width) by 24 (height)
Serviceability features: Easy-to-clean filter, easier-to-use handheld remote controller, coil refresher function, pop-open cover for ease of picture changing; condenser has diagnostic function for maintenance.
Technical support: Available 8 a.m.-6 p.m. Central at 888-865-3026.
Technical support materials: Submittals, IOM manuals, service manuals, parts lists, exploded parts views, component wiring diagrams.
Noise-reduction features: Variable-speed compressor and condenser fans; factory-installed internal insulation.
IAQ equipment supported: Heat pumps include plasma air purifying systems.
Thermostat compatibility: Requires a special thermostat.
Replacement parts compatibility: Some shared parts, some unique.
Additional features: Combines air conditioning and climate control for an all-in-one solution. It provides a three dimensional airflow system with the look and feel of a photo frame, allowing end users to display any photo up to 20 inches inside the frame.
Warranty information: Two-year operational parts, five-year compressor.
Special installation requirements: The indoor units have factory-installed electronic expansion valves that eliminate the need for field-provided expansion devices.
Contact: LG Electronics USA, 312-397-6064; www.lghvac.com.
eProduct 216
Lochinvar
Model: Knight® wall-mount fire-tube boiler (WHN055-359)
Footprint (inches): 22 (length) by 25 (width) by 36 (height)
Serviceability features: Enhanced Smart System™ control, which includes a larger display screen to communicate more information, soft keys for setting adjustments, an encoder knob for fast transitions between screens, and color coding functionality.
Technical support: Available at 800-722-2101, 8 a.m.-5 p.m. Central.
Technical support materials: Wiring and piping diagrams, literature, I&O manual, service manual, user manual, pump recommendations, replacement parts list, product summary, warranty information, plan view drawings, typical spec, technical service, etc., are available online.
Noise-reduction features: No special sound reduction measures are required.
IAQ equipment supported: Manufacturer did not specify.
Thermostat compatibility: The Smart System control is a dedicated circuit board which, among many other functions, acts as the thermostat.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: The new models offer up to 99 percent thermal efficiency, low-NOx emissions, and a fully modulating burner. Developed to provide contractors with all of the options they need to serve every application, the new models feature an innovative fire tube design. The operating control, coupled with the space-saving design, offers easier installation and maintenance.
Warranty information: Twelve-year limited covers the heat exchanger for leakage, thermal shock, or other malfunctions caused by defects in materials and/or workmanship. It extends to the first owner as long as the boiler remains installed at its original place of installation.
Special installation requirements: The re-engineered control offers installers easier access to necessary set-up information. The built-in-cascading sequencer allows up to eight boilers to be installed with either lead-lag operation or efficiency-optimized cascade operation to help installers fine tune the installation of multiple boilers. The new units offer seven venting options and tremendous flexibility for placement within any building.
Contact: Lochinvar Corp., 615-889-8900; www.lochinvar.com.
eProduct 217
Luxaire
Model: HL6B Acclimate single-stage heat pump
Footprint (inches): 37-42 (length) by 31-34 (width) by 40 (height)
Serviceability features: A slide-down control compartment allows access to control components; angled service valves reduce overall installation time and cost. A full-end, full-service access panel gives entry to internal components. When integrated with the Acclimate communicating system, advanced control and diagnostic capabilities make servicing the unit even easier.
Technical support: First level of support is provided by the distributor. Factory support is available to distributors and dealers by calling 877-874-7378 7 a.m.-6 p.m. Eastern.
Technical support materials: A full technical guide and installation instructions for the series, including wiring diagrams, sizes, parts, accessories, part number and installation instructions, are available at www.upgnet.com or by request.
Noise-reduction features: Incorporates the SilentDrive™ System, which consists of a molded composite bulkhead that isolates the compressor from the rest of the unit; a unique, swept-wing fan design that allows air to flow smoothly and efficiently across the fan tips; a molded composite base pan; and a sturdy fan guard.
IAQ equipment supported: Compatible with Luxaire brand indoor products, including filters, humidifiers, and UV lights.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: A new control board communicates with all key components in a home comfort system. A microprocessor defrost control system provides optimal comfort and monitors the overall system for reliability, automatically shutting the unit down if improper operating conditions occur.
Warranty information: Standard five-year limited parts, 10-year limited compressor. Premium system warranty includes limited lifetime compressor when matched with an approved furnace or UPG air handler and coil. Extended 10-year limited parts warranty when product is registered online within 90 days of purchase for replacement, or closing for new home construction.
Special installation requirements: The outdoor part of a versatile heat pump system, designed for convenient serviceability and installation. These communicating heat pumps can identify themselves to the Luxaire Communicating Control, allowing for faster setup and more powerful diagnostics.
Contact: Johnson Controls, 414-524-4338; www.joinluxaire.com.
eProduct 218
Maytag
Model: MGC2SD/M M120 gas furnace
Footprint (inches): 28 (length) by 14-25 (width) by 35 (height)
Serviceability features: Low height makes this furnace easier to apply in low-ceiling applications and works well with taller, high-SEER coils. Diagnostic lights provide troubleshooting without counting flashes. A color-coded wire harness is designed for ease of service and replacement.
Technical support: Available at 866-262-9824 Monday-Friday, 8 a.m.-4:30 p.m. Central. Technical literature via dealer log-in website or www.nordyneu.com.
Technical support materials: Wiring diagrams, replacement parts lists, installation instructions.
Noise-reduction features: Sealed and insulated blower compartment and sealed vestibule.
IAQ equipment supported: Integrated control board with connections for electronic air cleaner and humidifier.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: All furnaces are 100 percent fired and tested on the manufacturing line. Includes packaging with a corner post design to ensure that the product arrives damage-free.
Warranty information: With product registration, 12-year all parts and one-year Dependability Promise to replace entire unit if the heat exchanger fails.
Special installation requirements: Manufacturer did not specify.
Contact: Nordyne, 636-561-7300; www.maytaghvac.com.
eProduct 219
Model: MSH4BF heat pump
Footprint (inches): 31 (length) by 31 (width) by 45 (height)
Serviceability features: To make servicing easier for the contractor, access panels are provided to all controls and compressor from the side of the unit. A removable top grille assembly allows service from the top without disconnecting motor leads.
Technical support: Available at 866-262-9824 Monday-Friday, 8 a.m.-4:30 p.m. Central. Technical literature via dealer log-in website or www.nordyneu.com.
Technical support materials: Technical specs, wiring diagrams, and installation instructions are available on www.nordyneu.com.
Noise-reduction features: Composite base pan absorbs sound and is corrosion resistant. Hot gas muffler. Copeland UltraTech scroll compressor for silent, two-stage operation.
IAQ equipment supported: Air cleaners, humidifiers, UV lights, and zoning.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: These heat pumps are cost-effective alternatives to the brand’s premium equipment. The MSH4BF is a 16-SEER, 9.0-HSPF heat pump that can qualify for tax credits.
Warranty information: Twelve-year all parts and one-year Dependability Promise to replace the entire unit if its compressor fails within the first year of operation to the original owner. All split-system products must be installed with a matched indoor air handler or coil to qualify. Consumer product registration required within a limited period of time after installation.
Special installation requirements: None
Contact: Nordyne, 636-561-7300; www.maytaghvac.com.
eProduct 220
Miller
Model: CMF95 gas furnace
Footprint (inches): 24 (length) by 18 (width) by 57 (height)
Serviceability features: Dedicated flame sensor light and two lights in combination indicate fault codes without counting flashes.
Technical support: Available at 800-422-4328 Monday-Friday, 8 a.m.-4:30 p.m. Central. Technical literature via www.nordyneu.com.
Technical support materials: Wiring diagrams, replacement parts lists, installation instructions.
Noise-reduction features: Manufacturer did not specify.
IAQ equipment supported: Manufacturer did not specify.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: A 95 percent-AFUE furnace in classic 18-inch width for tight replacement jobs.
Warranty information: With product registration, five-year all parts, one-year labor.
Special installation requirements: Manufacturer did not specify.
Contact: Nordyne, 636-561-7300; www.millerac.com.
eProduct 221
Model: M7 gas furnace
Footprint (inches): 25 (length) by 20 (width) by 56 (height)
Serviceability features: Easy-open pawl latch secures the door in transit, and allows removal for access.
Technical support: Available at 800-422-4328 Monday-Friday, 8 a.m.-4:30 p.m. Central. Technical literature via www.nordyneu.com.
Technical support materials: Wiring diagrams, replacement parts lists, installation instructions.
Noise-reduction features: Quiet operation through uniquely designed in-shot burners, inducer location, and cabinet insulation.
IAQ equipment supported: Manufacturer did not specify.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: All furnaces are 100 percent fired and tested on the manufacturing line. This 95 percent-efficient furnace fits a standard manufactured housing footprint.
Warranty information: With product registration, five-year all parts and one-year labor.
Special installation requirements: Manufacturer did not specify.
Contact: Nordyne, 636-561-7300; www.millerac.com.
eProduct 222
Mitsubishi Electric Cooling & Heating
Model: H2i® M-Series (MUZ-FE09) split system
Footprint (inches): 11 (length) by 32 (width) by 22 (height)
Serviceability features: Built-in self-diagnostics direct technicians to a specific issue. Front, side, and top panels allow access to serviceable components. Accessible filters, no ductwork, and simpler wiring result in minimal maintenance.
Technical support: Available at 877-391-5550 8 a.m.-7 p.m. Eastern.
Technical support materials: Diagrams, troubleshooting FAQs, installation instructions, submittals, and spec sheets available online.
Noise-reduction features: Manufacturer did not specify.
IAQ equipment supported: The indoor unit’s multipart filter system removes contaminants like allergens, viruses, and bacteria from the air. A hybrid catechin-prefilter system absorbs odor-causing gases. A blue-enzyme anti-allergen filter reduces germs and traps particles. Some units have the Platinum Catalyst deodorizing filter that uses nanotechnology for high-power odor absorption.
Thermostat compatibility: Requires a special thermostat.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: Systems are Energy Star rated while delivering exceptional heating performance, operating at 100 percent capacity at temperatures down to 5˚F and provide heating down to -13˚ without a supplemental heat source. The i-See™ sensor scans the room and makes real-time adjustments based on ambient temperature readings for comfort.
Warranty information: Five-year parts and defects, seven-year compressors.
Special installation requirements: Manufacturer did not specify.
Contact: Mitsubishi Electric Cooling & Heating, 678-376-2900; www.mitsubishipro.com.
eProduct 223
Model: H2i P-Series (PUZ-HA36NHA2) split system
Footprint (inches): 13 (length) by 37 (width) by 53 (height)
Serviceability features: Built-in self-diagnostics direct a technician to a specific issue. Convenient front, side, and top panels allow access to serviceable components. Accessible filters, no ductwork, and simple wiring result in minimal maintenance.
Technical support: Available at 877-391-5550 8 a.m.-7 p.m. Eastern.
Technical support materials: Diagrams, troubleshooting FAQs, installation instructions, submittals, and spec sheets available online.
Noise-reduction features: Manufacturer did not specify.
IAQ equipment supported: The indoor unit’s multipart filter system removes contaminants like allergens, viruses, and bacteria from the air. A hybrid catechin-prefilter system absorbs odor-causing gases. A blue-enzyme anti-allergen filter reduces germs and traps particles. Some units have a Platinum Catalyst deodorizing filter that uses nanotechnology for high-power odor absorption.
Thermostat compatibility: Requires a special thermostat.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: Units operate at 100 percent of rated heating capacity at 5˚F and 80 percent at -13˚F. H2i technology helps the system overcome issues associated with conventional heat pumps in extremely cold climates, such as decreases in low-side pressure, refrigerant mass flow rate, and operational capacity.
Warranty information: Seven-year compressor, five-year parts.
Special installation requirements: Manufacturer did not specify.
Contact: Mitsubishi Electric Cooling & Heating, 678-376-2900; www.mitsubishipro.com.
eProduct 224
Modine
Model: Hot Dawg H2O unit heater
Footprint (inches): 32 (length) by 14 (width) by 12 (height)
Serviceability features: Manufacturer did not specify.
Technical support: Manufacturer did not specify.
Technical support materials: Materials are available for download at website.
Noise-reduction features: Manufacturer did not specify.
IAQ equipment supported: Manufacturer did not specify.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Manufacturer did not specify.
Additional features: This is a low-profile hot water unit heater with no external moving parts. It’s an appropriate solution for residential garages, basements, and vestibules, or commercial, industrial, and institutional settings. It can deliver air horizontally or vertically due to its mounting flexibility.
Warranty information: One-year unit and parts.
Special installation requirements: The unit can be installed with horizontal air delivery both perpendicular to and parallel with ceiling joists. It’s also narrow enough to provide vertical air delivery when recessed between joists.
Contact: Modine, 800-828-4328; www.modinehvac.com/hotdawg.
eProduct 225
Napoleon Heating and Cooling
Model: 9600 Series gas furnace
Footprint (inches): 29 (length) by 18 (width) by 33 (height)
Serviceability features: Easy to service and troubleshoot with the Integrated Furnace Control (IFC), which constantly monitors the furnace and its safety features. The IFC will advise what the problem may be with easier-to-read flash codes. The Sureview window lets the technician diagnose without taking the door off in some situations.
Technical support: Available 8 a.m.-5 p.m. Monday-Friday at 866-539-2039.
Technical support materials: The installation operation manual (IOM) supplied with the unit has all of the information needed to effectively troubleshoot or install the unit. Wiring diagrams and fault codes are on the inside of the top door. All replacement parts are in the IOM and all information is also available on the website.
Noise-reduction features: The cabinet is designed with both acoustical and thermal insulation. The ramp-up, ramp-down feature of the motor blower gives quiet performance.
IAQ equipment supported: This product has controls for humidification or indoor air filtration (EAC).
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: Sureveiw window enables the customer to see the flame in operation. The 9600 Series is the shortest high-efficiency furnace on the market and has one of the largest derates to low fire (40 percent), which enables the furnace to have higher efficiency while providing an even flow of heat. The programmed ECM’s ramp-up, ramp-down feature gives consistent airflow and low blower noise.
Warranty information: All registered products receive the Presidential extended warranty with 10-year parts and lifetime heat exchanger. If the heat exchanger fails within the first 10 years, Napoleon will supply a new furnace. Registration is online.
Special installation requirements: Easily installed in all four positions with no additional kits; converted to LP with one kit for the entire model line.
Contact: Napoleon Heating & Cooling, 800-461-5581; www.napoleonheatingandcooling.com.
eProduct 226
NuTone
Model: FG7SD/M gas furnace
Footprint (inches): 28 (length) by 14-25 (width) by 35 (height)
Serviceability features: Low height makes this furnace easier to apply in low-ceiling applications and works well with taller, high-SEER coils. Diagnostic lights provide troubleshooting without counting flashes. A color-coded wire harness is designed for service and replacement.
Technical support: Available at 800-422-4328 Monday-Friday, 8 a.m.-4:30 p.m. Central. Technical literature via dealer log-in website or www.nordyneu.com.
Technical support materials: Wiring diagrams, replacement parts lists, installation instructions.
Noise-reduction features: Sealed and insulated blower compartment and sealed vestibule.
IAQ equipment supported: Integrated control board with connections for electronic air cleaner and humidifier.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: All furnaces are 100 percent fired and tested on the manufacturing line. Includes packaging with a corner post design to ensure that the product arrives damage-free to the homeowner.
Warranty information: With product registration, 10-year all parts and 10-year Quality Pledge to replace entire unit if the heat exchanger fails.
Special installation requirements: Manufacturer did not specify.
Contact: Nordyne, 636-561-7300; www.nutonehvac.com.
eProduct 227
Model: Q5RF packaged heat pump
Footprint (inches): 49 (length) by 35 (width) by 30-38 (height)
Serviceability features: High- and low-pressure controls and high-low service ports allow access without disrupting operation. Liquid line filter-driers. Crankcase heater protects from liquid flood back. Designed to make servicing easier with access panels provided to the compressor and access to the evaporator coil for cleaning and general maintenance.
Technical support: Available at 800-422-4328 Monday-Friday, 8 a.m.-4:30 p.m. Technical literature and training videos are available on dealer log-in site and www.nordyneu.com.
Technical support materials: Wiring diagrams, replacement parts lists, installation instructions.
Noise-reduction features: Compressor sound blanket, energy-efficient brushless dc (ECM) blower motor.
IAQ equipment supported: State-of-the-art Copeland Ultra-Tech scroll compressor provides two-stage heat/cool for temperature control.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: Protected distributor tubes, both indoor and outdoor coils include very high abrasion resistance fiberglass sleeves to prevent leaks from tubing rubbing together. A wire guard coated with Earth-friendly epoxy and mesh hail guard that will never rust, protects the coil from being damaged by balls, lawnmowers, hail, etc.
Warranty information: Ten-year all parts and 10-year Quality Pledge to replace the entire unit if its compressor fails within the first 10 years of operation to the original owner. Consumer product registration required within a limited period of time after installation.
Special installation requirements: Zero-inch clearance to combustibles on duct side of the unit allows for installations in tight areas.
Contact: Nordyne, 636-561-7300; www.nutonehvac.com.
eProduct 228
Payne
Model: PG95XAT two-stage furnace
Footprint (inches): 29 (length) by 14-25 (width) by 35 (height)
Serviceability features: Brighter fault-code LED is easier to read. Fault codes stay in memory even after power shuts off. Large twist knobs make door removal easier. Blower assembly slides out on rails after the removal of two screws. Main wiring harness is long enough to allow technicians to remove/service blower without disconnecting wires.
Technical support: Support provided through nationwide network of local distributors.
Technical support materials: Installation and startup instructions, troubleshooting guide, critical parts list, and wiring diagram available on www.hvacpartners.com.
Noise-reduction features: Single-pass, secondary heat exchanger allows condensate to pass through quietly. Special blower mount quiets vibration and cuts sound. Cabinet insulation absorbs sound from heat exchanger and blower compartments.
IAQ equipment supported: Compatible with humidifiers, electronic air cleaners, UV lights, and other IAQ products.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Some shared parts, some unique.
Additional features: Two-stage heat capability; designed for four-way multiposition installation at 35 inches tall, with cabinet widths as narrow as 14 inches.
Warranty information: 20-year heat exchanger and 10-year parts limited to original purchaser with timely registration. Limited warranty period for parts is five years if not registered within 90 days of installation (warranty certificate provides details and restrictions).
Special installation requirements: None.
Contact: Payne Heating & Cooling, 881-417-2963; www.payne.com.
eProduct 229
Model: PH15NB heat pump
Footprint (inches): 31-35 (length) by 31-35 (width) by 29-39 (height)
Serviceability features: All electrical controls are located behind a single panel. Removal of top gives access to fan motor, compressor, and condenser coil. Refrigerant connections are positioned at 45-degree angle to allow outdoor unit to be positioned facing to either right or left along exterior wall.
Technical support: Support provided through nationwide network of local distributors.
Technical support materials: Installation and startup instructions, troubleshooting guide, critical parts list, and wiring diagram on www.hvacpartners.com.
Noise-reduction features: Rubberized grommets create a buffer between the base pan and the compressor to minimize noise from vibrations. Vertical air discharge carries sound and condenser air up and away from adjacent patio areas.
IAQ equipment supported: Compatible with humidifiers, UV lamps, electronic air cleaners, and other IAQ products.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: Offers a combination of reliable performance and dealer-friendly features in a 15-SEER heat pump.
Warranty information: Ten-year parts limited (including compressor) with timely registration (restrictions apply; see warranty certificate for details).
Special installation requirements: None.
Contact: Payne Heating & Cooling, 881-417-2963; www.payne.com.
eProduct 230
Philco
Model: KG7SD/M gas furnace
Footprint (inches): 28 (length) by 14-25 (width) by 35 (height)
Serviceability features: Low height makes this furnace easier to apply in low-ceiling applications and works well with taller, high-SEER coils. Diagnostic lights provide troubleshooting without counting flashes. A color-coded wire harness is designed for ease of service and replacement.
Technical support: Available at 800-422-4328 Monday-Friday, 8 a.m.-4:30 p.m. Central. Technical literature via www.
nordyneu.com.
Technical support materials: Wiring diagrams, replacement parts lists, installation instructions.
Noise-reduction features: Sealed and insulated blower compartment and sealed vestibule.
IAQ equipment supported: Integrated control board with connections for electronic air cleaner and humidifier.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: All furnaces are 100 percent fired and tested on the manufacturing line. Includes packaging with a corner post design to ensure that the product arrives damage-free to the homeowner.
Warranty information: With product registration, 10-year all parts and one-year Quality Pledge to replace entire unit if the heat exchanger fails.
Special installation requirements: Manufacturer did not specify.
Contact: Nordyne, 636-561-7300; www.philcohvac.com.
eProduct 231
Rheem
Model: Prestige Series™ modulating gas furnace (RGFG) with Comfort Control2 System™ and Contour Comfort Control™
Footprint (inches): 30 (length) by 18-25 (width) by 34 (height)
Serviceability features: Equipped with exclusive Comfort Control2 System (CC2S), the furnace provides 28 on-board diagnostic and fault history codes by detecting system and electrical problems. It also contains nearly 50 error and operational status codes accessible via the CC2S thermostat, which provides information for faster, more accurate service.
Technical support: Available at 479-648-6237 Monday-Friday, 8 a.m.-5 p.m. Central.
Technical support materials: Spec sheets, wiring diagrams, accessory sheets, installation instructions, use and care sheets, LP conversion kits, warranty information, parts lists, and submittal sheets.
Noise-reduction features: Reduced firing rates, an efficient ECM 3.0 motor, insulation, and solid doors.
IAQ equipment supported: Equipped with a low-speed constant fan and constant temperature rise for comfort. Units also feature humidification and dehumidification controls.
Thermostat compatibility: Compatible with most thermostats. Modulating thermostat recommended for optimal performance.
Replacement parts compatibility: Some shared parts, some unique.
Additional features: A conventional furnace is either off or on at 100 percent capacity, depending on the demand for heat. The Prestige Series furnace features true modulation from 40-100 percent of operation, initiated by the special modulating thermostat, not a timed algorithm on a control board like some competitive products.
Warranty information: Limited lifetime heat exchanger; 10-year parts; limited lifetime warranty for unit replacement with registration.
Special installation requirements: Unit follows standard installation practices.
Contact: Rheem Manufacturing Co., 479-646-4311; www.rheem.com.
eProduct 232
Ruud
Model: Ultra Series™ 90 Plus communicating modulating upflow gas furnace (RGFG) with Comfort Control² System and Contour Comfort Control
Footprint (inches): 30 (length) by 18-25 (width) by 34 (height)
Serviceability features: Dual seven-segment LED display on the control board shows the source of any system malfunctions. Should the power fail, the furnace will retain the system’s operation history for the last six fault codes and will display them on the control board for quick viewing.
Technical support: Available at 479-648-6237 Monday-Friday, 8 a.m.-5 p.m., Central.
Technical support materials: Spec sheets, wiring diagrams, accessory sheets, installation instructions, use and care sheets, LP conversion kits, warranty information, parts lists, and submittal sheets.
Noise-reduction features: Reduced firing rates, an efficient ECM 3.0, insulation, and solid doors.
IAQ equipment supported: Units are equipped with a low-speed constant fan and constant temperature rise for comfort. The units also feature humidification and dehumidification controls.
Thermostat compatibility: Compatible with most thermostats. Modulating thermostat recommended.
Replacement parts compatibility: Some shared parts, some unique.
Additional features: Because of the low-profile, 34-inch height, the unit is appropriate for space-constrained installations and can be used vertically to satisfy most applications that traditionally call for a horizontal furnace, simplifying the installation process for the contractor.
Warranty information: Limited lifetime heat exchanger; 10-year parts; limited lifetime warranty for unit replacement with registration.
Special installation requirements: This unit follows standard installation practices.
Contact: Ruud, 479-646-4311; www.ruud.com.
eProduct 233
Samsung
Model: Neo Forte
Footprint (inches): 8 (length) by 33 (width) by 11 (height)
Serviceability features: Manufacturer did not specify.
Technical support: Available at 717-243-2535 from 7:30 a.m.-5 p.m. in Carlisle, Pa.; 817-838-6066 8 a.m.-5 p.m. in Fort Worth, Texas; and 888-699-6067, 8 a.m.-5 p.m. in Santa Fe Springs, Calif.
Technical support materials: Go online for submittals, wiring diagrams, installation, and service manuals.
Noise-reduction features: Neo Forte has a noise level of 22 dB. The compressor operates at the lowest speed possible when maintaining the desired set temperature. This means very low noise levels from the fan motor and compressor.
IAQ equipment supported: Well equipped to provide fresh, clean, and healthy air; each unit has a built-in silver-coated filter, which has been widely recognized for its antibacterial and sanitization effects.
Thermostat compatibility: Requires a special thermostat.
Replacement parts compatibility: Does not share replacement parts with other models.
Additional features: Saves energy for its users. The S-inverter prevents frequent switching on and off of the compressor. By not having to always switch on and off, it can save up to 50 percent in energy costs compared to non-inverter systems.
Warranty information: Five-year compressor, three-year parts.
Special installation requirements: Manufacturer did not specify.
Contact: Quietside Corp., 717-243-2535; www.quietside.com.
eProduct 234
Sanyo
Model: 30/36KHS82 ductless heat pump
Footprint (inches): 9 (length) by 42 (width) by 12 (height)
Serviceability features: Outdoor unit includes diagnostic feature on control board. Indoor remote provides diagnostic feature as well as test run mode.
Technical support: Available Monday-Friday, 8:30 a.m.-5:30 p.m. Eastern at 800-851-1235 or via email (hvac.service@sna.sanyo.com).
Technical support materials: All information including service manual, installation manual, operating manual, and complete specs are available for download at website.
Noise-reduction features: Manufacturer did not specify.
IAQ equipment supported: Manufacturer did not specify.
Thermostat compatibility: Requires a special thermostat.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: Manufacturer did not specify.
Warranty information: Seven-year compressor, five-year parts.
Special installation requirements: Manufacturer did not specify.
Contact: Sanyo North America, 800-851-1235; www.sanyohvac.com.
eProduct 235
Tappan
Model: FG7SD/M gas furnace
Footprint (inches): 28 (length) by 14-25 (width) by 35 (height)
Serviceability features: Low height makes this furnace easier to apply in low-ceiling applications and works well with taller, high-SEER coils. Diagnostic lights provide troubleshooting without counting flashes. A color-coded wire harness is designed for ease of service and replacement.
Technical support: Available at 800-422-4328 Monday-Friday, 8 a.m.-4:30 p.m. Central. Technical literature via dealer log-in website or www.nordyneu.com.
Technical support materials: Wiring diagrams, replacement parts lists, installation instructions.
Noise-reduction features: Sealed and insulated blower compartment and sealed vestibule.
IAQ equipment supported: Integrated control board with connections for electronic air cleaner and humidifier.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: All furnaces are 100 percent fired and tested on the manufacturing line. Includes packaging with a corner post design to ensure that the product arrives damage-free to the homeowner.
Warranty information: With product registration, 10-year all parts and 10-year Tough Quality Pledge to replace entire unit if the heat exchanger fails.
Special installation requirements: Manufacturer did not specify.
Contact: Nordyne, 636-561-7300; www.tappan.net.
eProduct 236
Model: FT4BI heat pump
Footprint (inches): 31 (length) by 31 (width) by 37-45 (height)
Serviceability features: Inverter-driven rotary compressor provides fully variable operation. Full-port brass ball valves provide low pressure drop and ease of service. The valves are actuated by quarter-turn full open to full close. Compressor and control access. Diagnostics provided by communicating controller.
Technical support: Available at 800-422-4328 Monday-Friday, 8:00 a.m.-4:30 p.m. Central. Technical literature and training videos are available on dealer log-in site and www.nordyneu.com.
Technical support materials: Technical specs, wiring diagrams, and installation instructions are available on www.nordyneu.com.
Noise-reduction features: Compressor sound blanket, composite base pan, and swept-wing fan blade reduce unwanted noise. Operation as low as 59 dB.
IAQ equipment supported: Air cleaners, humidifiers, UV lights, and iQ Zone zoning. Built-in humidity control activates humidifier equipment (if supplied), and reduces blower speed if indoor rh is greater than setpoint (default set at 60 percent).
Thermostat compatibility: Requires a special thermostat.
Replacement parts compatibility: Some shared parts, some unique.
Additional features: Fully variable-speed inverter-driven rotary compressor technology and variable-speed indoor and outdoor motors. Operates near the nominal rated capacity at the thermostat setpoint and modulates as the temperature difference setpoint and room temperature change. The system may run at additional 18 percent capacity to provide rapid cooling.
Warranty information: Ten-year all-parts and 10-year Quality Pledge to replace the entire unit if its compressor fails within the first 10 years of operation to the original owner. All split-system products must be installed with a matched indoor air handler or indoor coil to qualify. Consumer product registration required within a limited period of time after installation.
Special installation requirements: Dealers must be factory certified before selling or installing an iQ Drive system.
Contact: Nordyne, 636-561-7300; www.tappan.net.
eProduct 237
Tempstar
Model: SmartComfort® IIX 96 gas furnace
Footprint (inches): 29 (length) by 14-25 (width) by 35 (height)
Serviceability features: Blower assembly is mounted on rails for up-front installation and removal. Furnaces feature large, robust one-quarter turn knobs for door installation and removal. A bright LED makes diagnostic flash codes easier to read, lets technicians see the most recent fault code even if power shuts off.
Technical support: Technical Service Advisor on staff at local distributors is available with technical assistance, troubleshooting. Technical training is available 24/7/365 online and at field schools held at participating distributor locations nationwide.
Technical support materials: Product information posted at dealer website includes product spec sheets, installation-operation manuals, and technical support/parts manuals.
Noise-reduction features: The blower motor is attached with soft-mount rubber grommets that absorb sound and vibration. Furnaces feature insulated heat exchanger and blower compartments to muffle sound and absorb vibration noise.
IAQ equipment supported: When coupled with a condensing unit and humidity-capable thermostat, mainline Tempstar furnaces can control relative humidity during cooling operation. These furnaces have a dehumidification function in cooling mode and can control a humidifier accessory in heating mode.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Some shared parts, some unique.
Additional features: Designed for four-way multiposition installation, 35 inches tall and lighter weight than previous counterparts, these two-stage models feature ECM blower motors that can deliver an increase in cooling efficiency when paired with select condensing units and evaporator coils. Meets low-NOx emissions standards.
Warranty information: Five-year No Hassle Replacement™ limited warranty. Lifetime heat exchanger and 10-year parts limited to original purchaser with timely registration. Limited warranty period is 20-year heat exchanger and five-year parts if not registered within 90 days of installation (see warranty certificate for details and restrictions).
Special installation requirements: None.
Contact: International Comfort Products, LLC (ICP), 800-315-4370; www.gotempstar.com.
eProduct 238
Model: SmartComfort® VC 97 gas furnace
Footprint (inches): 29 (length) by 18-25 (width) by 35 (height)
Serviceability features: Features large, one-quarter turn knobs for door installation and removal. A bright LED makes diagnostic flash codes easier to read. Blower assembly is mounted on rails for up-front installation and removal, letting technicians see the last seven fault codes even if power shuts off.
Technical support: Technical Service Advisor on staff at local distributors is available with technical assistance, troubleshooting. Technical training is available 24/7/365 online and at field schools held at participating distributor locations nationwide.
Technical support materials: Product information posted online includes product spec sheets, installation-operation manuals, and technical support/parts manuals.
Noise-reduction features: Variable-speed ECM blower motor reduces operating sound levels. Special blower mount quiets vibration and cuts sound. Cabinet insulation absorbs sound from heat exchanger and blower compartments.
IAQ equipment supported: When coupled with a condensing unit and humidity-capable thermostat, mainline Tempstar furnaces can control relative humidity during cooling operation. These furnaces have a dehumidification function in cooling mode and can control a humidifier accessory in heating mode.
Thermostat compatibility: Requires a special thermostat. For a self-configuring control to function, must use with new Tempstar communicating control (thermostat).
Replacement parts compatibility: Some shared parts, some unique.
Additional features: Featuring self-configuring control, these furnaces are built with stainless steel primary and secondary heat exchangers. Modulating (multistage) gas valves allow furnaces to operate on a quieter low-fire setting unless thermostat calls for more heat. Designed for four-way multiposition installation, 35 inches tall, and lighter weight than previous counterparts.
Warranty information: Ten-year No Hassle Replacement™ limited warranty. Lifetime heat exchanger and 10-year parts limited to original purchaser with timely registration. Limited warranty period is 20-year heat exchanger and five-year parts if not registered within 90 days of installation (see warranty certificate for details and restrictions).
Special installation requirements: None.
Contact: International Comfort Products LLC (ICP), 800-315-4370; www.gotempstar.com.
eProduct 239
TETCO Geothermal
Model: ES4 Series TCT combination vertical packaged geothermal water-air unit
Footprint (inches): 32 (length) by 30 (width) by 60-56 (height)
Serviceability features: Eye-level mounted controls with individual LED fault lights. Full 360-degree access to all components. Five compressor-section access panels and three blower-section access panels.
Technical support: Available 24 hours a day.
Technical support materials: Wiring diagrams, full documentation, parts list, and service and troubleshooting guidance.
Noise-reduction features: Quadruple compressor isolation, gasketed access panels, heavy closed-cell foam insulation.
IAQ equipment supported: E-coated air coils. Composite drain pan with silver-ion antimicrobial protection built in. Pleated air filters. Compatible with most IAQ products.
Thermostat compatibility: Requires a special thermostat (heat pump thermostat and aquastat).
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: The first multipositional combination geothermal heat pump in the industry. The unit provides forced-air heating and cooling, as well as hydronic heating for radiant floors and other applications. All models in the TCT Series meet Energy Star Tier 3 performance ratings.
Warranty information: Five-year labor, five-year all parts, 10-year compressor. Optional 10-year labor, 10-year all parts. Optional lifetime compressor.
Special installation requirements: Manufacturer did not specify.
Contact: Enertech Manufacturing LLC, 618-664-9010; www.enertechmfg.com.
eProduct 240
Model: ES4 Series THT horizontal packaged geothermal water-air unit
Footprint (inches): 54-68 (length) by 26-30 (width) by 22-24 (height)
Serviceability features: Three compressor-section access panels and two blower-section access panels. Individual fault LED lights on the control board. Access to all components throughout the cabinet.
Technical support: Available 24 hours a day.
Technical support materials: Wiring diagrams, full documentation, parts list, service and troubleshooting guidance.
Noise-reduction features: Fully insulated cabinet with gasketed access panels to eliminate panel rattle. Isolated compressor and blower mounting.
IAQ equipment supported: Recycled, foil face, blue-jean insulation. E-coated air coils. Stainless steel drain pans.
Thermostat compatibility: Requires a special thermostat (heat pump thermostat).
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: The THT Series features a highly ridged cabinet, with all models meeting Energy Star Tier 3 ratings.
Warranty information: Five-year labor, five-year all parts, 10-year compressor. Optional 10-year labor, 10-year all parts. Optional lifetime compressor.
Special installation requirements: Manufacturer did not specify.
Contact: Enertech Manufacturing LLC, 618-664-9010; www.enertechmfg.com.
eProduct 241
Trane
Model: XV95 gas furnace (TUH2B080A9V4VA, TUH2C100A9V5VA, TDH2B080A9V4VA)
Footprint (inches): 40 (length) by 18-21 (width) by 28 (height)
Serviceability features: Products are designed with exacting specs and innovative features that wear well over time. They’re easier to access and service for better long-term performance and a longer life. The XV95 is convertible to horizontal left.
Technical support: Contact local distributor.
Technical support materials: The ComfortSite Intranet for dealers and distributors provides quick access to the most current support materials, including catalog pages, installer guides, service facts, product data, submittals, and owners’ manuals.
Noise-reduction features: Heavy steel insulated cabinet. Insulated panels hold more heat in the furnace to ensure greater durability and reduce operating sound.
IAQ equipment supported: CleanEffects whole-house air cleaner can be added for advanced air filtration that removes more dust, pollen, and other irritants from conditioned air for a cleaner, healthier, more comfortable home.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: New models provide higher tonnage options with up to 97 percent AFUE for low-heat, high-cool applications. Two-stage heating uses gradual, steady warmth for efficiency, with plenty of reserve heat on standby. During summer, Comfort-R technology slows airspeed during startup for quieter operation and more precise humidity control.
Warranty information: Lifetime limited heat exchanger, 10-year limited internal functional parts. If the product is not registered within 60 days of installation, base limited warranty terms will apply.
Special installation requirements: None.
Contact: Trane, 903-581-3467; www.trane.com.
eProduct 242
Model: EarthWise geothermal packaged system (T2GX)
Footprint (inches): Manufacturer did not specify.
Serviceability features: Precision control of the system, combined with on-board diagnostics, ensures reliability and long-lasting comfort.
Technical support: Contact local distributor.
Technical support materials: ComfortSite Intranet for dealers and distributors provides access to the most current support materials, including catalog pages, installer guides, service facts, product data, submittals, and owners’ manuals.
Noise-reduction features: One of the quietest home comfort solutions, with low sound levels, the company said.
IAQ equipment supported: Manufacturer did not specify.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: The T2GX offers up to 29.4 EER and is available in single- and two-stage designs. The variable-speed blower motor offers up to 12 airflow selections. Optional heating for water supply is available.
Warranty information: Ten-years parts-labor. No registration required.
Special installation requirements: Installation includes a large, fluid-filled loop that consists of an underground pipe system. There are four different configurations available for installation.
Contact: Trane, 903-581-3467; www.trane.com.
eProduct 243
Utica Boilers
Model: SSC gas modulating condensing boiler
Footprint (inches): 20 (length) by 14 (width) by 31 (height)
Serviceability features: Features original 316L/444 stainless steel fin tube heat exchanger; built-in primary-secondary piping; factory-installed probe-type, low water cut off; corrosion-resistant CPVC flue collector; control with text display; outdoor reset; priority domestic hot water; and integrated multiple-boiler control capability (up to 16 boilers).
Technical support: Available Monday-Friday, 7:30 a.m.-5 p.m. Eastern at 800-325-5479.
Technical support materials: Brochure, gas conversion instructions, IOM, parts list, user’s manual, manufacturer’s warranty, and additional warranty.
Noise-reduction features: Sealed housing reduces noise.
IAQ equipment supported: Manufacturer did not specify.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Some shared parts, some unique.
Additional features: Features a vertical-mounted, helical fin tube heat exchanger constructed of 316L/444 stainless steel fin tube. Vertical positioning prevents system sediment from settling in low spots caused by horizontal designs. Natural flexing and downward flow of condensate continually washes the combustion side of the SSC.
Warranty information: A 15-year limited heat exchanger, and availability of optional Comfort Plus Parts and labor extended warranties.
Special installation requirements: Replacement ready with 1 ¼-inch piping connections and low pressure drop — no high head pump required. Simplified electrical connections with removable terminal block. Jacket slides on and off for access. Wall-mount bracket included.
Contact: Utica Boilers, 315-797-1310; www.uticaboilers.com.
eProduct 244
Westinghouse
Model: FG7SD/M gas furnace
Footprint (inches): 28 (length) by 14-25 (width) by 35 (height)
Serviceability features:
Low height makes this furnace easier to apply in low-ceiling applications and works well with taller, high-SEER coils. Diagnostic lights provide troubleshooting without counting flashes. A color-coded wire harness is designed for service and replacement.
Technical support: Available at 800-422-4328 Monday-Friday, 8 a.m.-4:30 p.m. Central. Technical literature via dealer log-in website or www.nordyneu.com.
Technical support materials: Wiring diagrams, replacement parts lists, installation instructions.
Noise-reduction features: Sealed and insulated blower compartment and sealed vestibule.
IAQ equipment supported: Integrated control board with connections for electronic air cleaner and humidifier.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: All furnaces are 100 percent fired and tested on the manufacturing line. Includes packaging with a corner post design to ensure that the product arrives damage-free.
Warranty information: With product registration, 10-year all parts and 10-year Quality Pledge to replace entire unit if the heat exchanger fails.
Special installation requirements: Manufacturer did not specify.
Contact: Nordyne, 636-561-7300; www.westinghousehvac.com.
eProduct 245
Model: FT4BI heat pump
Footprint (inches): 31 (length) by 31 (width) by 37-45 (height)
Serviceability features: Inverter-driven rotary compressor provides fully variable operation. Full-port brass ball valves provide low pressure drop and ease of service. The valves are actuated by quarter-turn full open to full close. Compressor and control access. Diagnostics provided by communicating controller.
Technical support: Available at 800-422-4328 Monday-Friday, 8 a.m.-4:30 p.m. Central. Technical literature and training videos are available on dealer log-in site and www.nordyneu.com.
Technical support materials: Technical specs, wiring diagrams, and installation instructions are available on www.nordyneu.com.
Noise-reduction features: Compressor sound blanket, composite base pan, and swept wing fan blade reduce unwanted noise. Operation is as low as 59 dB.
IAQ equipment supported: Air cleaners, humidifiers, UV lights, and iQ Zone zoning. A built-in humidity control activates humidifier equipment (if supplied), and reduces blower speed if indoor rh is greater than setpoint (default set at 60 percent).
Thermostat compatibility: Requires a special thermostat.
Replacement parts compatibility: Some shared parts, some unique.
Additional features: Fully variable-speed inverter-driven rotary compressor technology, and variable-speed indoor and outdoor motors. It operates near the nominal rated capacity at the thermostat setpoint and modulates as the temperature difference setpoint and room temperature change. The system may run at additional 18 percent capacity to provide rapid cooling.
Warranty information: Ten-year all-parts and 10-year Quality Pledge to replace the entire unit if its compressor fails within the first 10 years of operation to the original owner. All split-system products must be installed with a matched indoor air handler or indoor coil to qualify. Consumer product registration required within a limited period of time after installation.
Special installation requirements: Dealers must be factory certified before selling or installing an iQ Drive system.
Contact: Nordyne, 636-561-7300; www.westinghousehvac.com.
eProduct 246
Whirlpool
Model: WGFMM96 gas furnace
Footprint (inches): 29 (length) by 18-25 (width) by 40 (height)
Serviceability features: Airtight solid bottom for side-return applications; easier-cut tabs for removal in bottom air-inlet applications; standard, easier-install top venting (alternate flue/vent locations available); convenient left or right connections for gas and electric service; multiposition installation (upflow, horizontal left or right).
Technical support: Available at 866-944-7575 8 a.m.-5 p.m. Eastern Monday-Friday.
Technical support materials: Technical specs, installation instructions, and general product information at www.whirlpoolcomfort.com.
Noise-reduction features: Quiet, variable-speed circulator motor; fully insulated steel cabinet with DuraShield™ coating; extra-low, constant fan speed; quiet, two-speed induced-draft blower.
IAQ equipment supported: Compatible with most installed IAQ filtering systems.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: Heavy-duty Pro stainless steel heat exchanger; precision silicon nitride igniter; self-diagnostic control board with color-coded terminal connections and provisions for electronic air cleaners and other installed IAQ products; Resource Saver™ model (outperforms minimum federal energy standards by up to 20 percent); Comfort Commitment™ Best-in-Class warranty.
Warranty information: Limited lifetime unit replacement; limited lifetime heat exchanger; limited 10-year parts.
Special installation requirements: None.
Contact: Tradewinds LLC, 904-407-4470; www.whirlpoolcomfort.com.
eProduct 247
Williams Furnace Co.
Model: Ten86542 and 1086541 vent-free heater
Footprint (inches): 14 (length) by 8 (width) by 21 (height)
Serviceability features: These 10,000-Btuh vent-free infrared heaters have manually controlled thermostats available for either natural or liquid propane gas. Direct heat from the radiant plaques quickly warms people and objects in the room before heating the air.
Technical support: Contact local distributor.
Technical support materials: Installation instructions, troubleshooting, wiring diagrams, etc., included with each unit. Parts and part numbers available from local distributor or online.
Noise-reduction features: Vent-free heaters are said to be a reliable and convenient secondary heat source, and for those hard-to-heat areas of a home or business.
IAQ equipment supported: Manufacturer did not specify.
Thermostat compatibility: Manually controlled.
Replacement parts compatibility: Some shared parts, some unique.
Additional features: Manufacturer did not specify.
Warranty information: One-year parts.
Special installation requirements: Unsurpassed ease of installation. All hardware is included to mount the unit to the wall or the floor; no vent or chimney required — simply connect to gas source. Meets or exceeds all safety and performance standards; includes matchless ignition, safety pilot systems, and safety grille over heating elements. Dual-purpose safety pilot system protects against oxygen depletion and any interruption in the fuel supply.
Contact: Williams Furnace Co., 949-500-8039; www.e-wfc.com.
eProduct 248
York
Model: YZF Affinity single-stage heat pump
Footprint (inches): 37-42 (length) by 31-34 (width) by 40 (height)
Serviceability features: A slide-down control compartment allows access to control components, and angled service valves reduce overall installation time and costs. A full-end, full-service access panel ensures entry to internal components. When integrated with the Affinity communicating control, advanced control and diagnostic capabilities make servicing the unit easier.
Technical support: First level of support is provided by the distributor. Factory support is available to distributors and dealers by calling 877-874-7378, 7 a.m.-6 p.m. Eastern.
Technical support materials: A full technical guide and installation instructions including wiring diagrams, sizes, parts, accessories, part number and installation instructions, are available online or by request.
Noise-reduction features: Incorporates the QuietDrive™ System, a group of features engineered to reduce sound. A molded composite bulkhead isolates the compressor from the rest of the unit; a swept-wing fan design allows air to flow smoothly and efficiently across the fan tips.
IAQ equipment supported: Compatible with York brand indoor products, including filters, humidifiers, and UV lights.
Thermostat compatibility: Compatible with most thermostats.
Replacement parts compatibility: Shares replacement parts with other models.
Additional features: A new control board communicates with all key components in a home comfort system. This unit also utilizes the York Guard VI microprocessor defrost control system, which provides optimal comfort and monitors the overall system for reliable operation, automatically shutting the unit down if improper operating conditions occur.
Warranty information: Standard five-year limited parts, 10-year limited compressor. Premium System warranty includes a limited lifetime compressor when matched with an approved furnace or UPG air handler and coil. Extended 10-year limited parts when product is registered online within 90 days of purchase (for replacement), or closing (for new home construction).
Special installation requirements: Unit is the outdoor part of a heat pump system designed for serviceability and installation. These communicating heat pumps can identify themselves to the York communicating control, allowing for faster setup and more powerful diagnostics.
Contact: Johnson Controls, 414-524-5487; www.yorkhvacdealer.com.
eProduct 249
Publication date: 09/12/2011
